• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.4
• /
• pp.49-55
• /
• 1986

The authors carried out an experiment to determine the horizontal opening of the mid water trawl gear, which is the same as was used in the foreward experiment concerned to the attitude and opening efficiency of otter board. The trawl net .used in the experiment was designed to have a square sectional four-seamed body with two three-sepenlted wings. Each wing tip was rigged with a net pendant of 70 m long and the fore ends of the pendants were directly jointed to the otter pendant without inserting hand rope, and a front weight of 200 kg weigh was rigged with in front of the lowest wing tip. To determine the opening between otter boards ani between wing tips, two 50 KHz fish finders were set sideways on the otter board and on the port middle wing tip so as to detect the distance froa the finders to the starboard otter board and to the wing tip respectively, and the informations were transmitted to the indicators onboard the ship through water-tight cables. The results obtained can be summarized as follows: 1. The openings between otter borads were 43-45 m in case of the warp 100 m, 53-55 m in the war;> 150 m and 54-59 m in the warp 200 m. It was increased in linear according to the increase of towin; speed in the range of 1. 1-1. 8 mlscc. 2. The determined values of the openings between otter boards were greater than the estimated values. which were calculated by the opening between warps at the gallows of the ship and the length of tt~ warp, assuming that the warps from the top rollers to the otter boards were straight. The rates of the determined values to the estimated values were 1. 23-11. 0 in case of the warp 100 m, 1. 23-1. 12 in the warp 150 m and 1. 23-1. 15 in the warp 200 m respectively. The rates were almost the same at the slow towing speed of 1. 3 mlscc or so, then the higher the speed, the less the rate, and the longer the warp, the greater the rate. 3. The rates of the openings between otter boards to the total length of net pendant and the net (excluded cod end) showed 43-43% in case of the warp 150-200 m. It was a little smaller than th~ standard. which is 50%. in the common bottom trawl. 4. The determined openings between wing tips were 18-19 m in case of the warp 100m, 21-22 m in the warp 150 rn, They showed that the higher the speed, the greater the openings even though its range was no more than 1 m or so. 5. The rates of openings between otter boards to th~ openings betwee:l wing tips were almost invariably 38%. 6. The rates of openigs b2tween otter boards to the lenth of h~ad rope were 60-65% in cas': of th~ warp lOa-150m. It were much larg2r than th~ standard. which is 50%. in the common botto:n trawl.

• Korean Journal of Human Ecology
• /
• v.12 no.1
• /
• pp.75-84
• /
• 2003

The objective of this paper was to analyse the foot type of female university students by the direct and indirect measure of foot and the measures of foot outline. The results were as follow: 1. The length and the width of foot were small and ankle slender and the modification of the big toe slight. 2. The analysis on the 16 measure items revealed five factors; the first factor was related to the width and girth of foot, the second one to the length of foot, the third one to the transformation of the little toe, the fourth one to the height of foot, the fifth one to transformation of the big toe. 3. The grouping on the shape of foot revealed three types. The inline angle of foot was the smallest in average in the type 1, while it appeared to be middle in the other types. The wider foot shapes were grouped as type 2 because their inline and outline angles of foot were the biggest in average. In the type 3, the big toe was curved a lot, since it was the largest in average. 4. From the naked eye measuring method, classification from which toe was popped-out told that Egyptian foot was 30.9%, Greek foot 27.9%. On the other hand, the instrumental method showed that Egyptian foot was 57.3%, Squared foot 35.3% and Greek foot 7.4%. 5. The result from the analysis about the traits of foot shape by the degree of the arch formation of bottom foot, showed that 33.8% had the normal foot, 66.2% slightly flat foot or middle one. There was no one with rigid flat foot. 6. The shoes size they declared were that 240cm was 33.3%, 235cm 18.1% and 245cm 18.1%. The shape of their shoe heel were flat heel(34.8%), cuban heel(25.5%), and narrow straight heel(19.9%); and that of the shoe toe were round toe(25.4%), oval toe(20.4%) and squared toe(20.4%). 7. The discomforting parts when they wear shoes were the little toe(35.4%), the rear of foot(13.9%), and the width of foot(13.9%), which was related to their dislike of shoe with the pointed toe.

• Microbiology and Biotechnology Letters
• /
• v.10 no.3
• /
• pp.227-232
• /
• 1982

The methods determining the growth rate of mold on beans were investigated in order to compare the growth of Aspergillus oryzae on lupinseed to that on soybean. The growth of A. oryzae on cooked whole or paste form of bean substrates was evaluated by the measurements of colony diameter and hyphae length of the mold. The mold showed characteristic lag times to form the colony on different types of substrate. The growth of colony diameter was coincided with the increase in $\alpha$-amino nitrogen content of the substrate when the moisture level of the substrates was similar each other. The colony diameter and the cultivation time after the lag period showed a straight line relationship, from which the growth rate was estimated. in general, lupinseed paste allowed faster growth of A. oryzae than soybean paste at the initial growth phase. The lag time to form the colony was 24.0 hrs on lupinseed paste and 44.4 hrs on soybean paste. The growth rate after colony formation was, however, 7.05 mm/day for lupinseed paste and 8.83mm/day for soybean paste, which indicated that the growth rate after the lag period was faster on soybean compared to lupinseed. The sporulation time of the mold was related to the lag time for the colony formation. The measurement of hyphae length on whole beans could be used as a simple and rapid method of estimating the growth property of mold on different substrates.11 showed that the growth of A. oryzae was partly hindered by the thick hull of the lupinseed.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.47 no.1
• /
• pp.25-35
• /
• 2020

The purpose of this study is to evaluate the morphological characteristics of the roots and roots canals of primary molar teeth using Cone-Beam Computed Tomography (CBCT). A total of 68 CBCT images of children aged 4 - 5 years was used for this study. A total of 160 molar teeth were analyzed. Various parameters such as the number of roots and canals, length of root and root canal, and the angulation and shape of the roots were analyzed. All maxillary primary molars had 3 roots. The presence of 2 root canals in 1 root was only observed in the mesiobuccal root of maxillary primary second molars. Most mandibular primary molars had 2 roots, and most mesial roots had 2 root canals. Concerning the length of the roots, the palatal root of the maxillary primary molar was found to be longest whereas the distobuccal root was shortest. In mandibular primary molars, the mesial root was longer than the distal root. In maxillary primary molars, the palatal root had the greatest angulation whereas the distal root has the greatest in mandibular molars. The root and root canals of maxillary primary molars were more curved in shape whereas mandibular primary molars were straight.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1327-1336
• /
• 2013

In this study, the effects of corrugated webs on the ultimate behavior of horizontally curved I-shaped girders are investigated. Because of the geometric characteristics of corrugated plates, corrugated webs can be used for enhancing torsional and warping stiffness of plate girders. Many researches have been conducted to study the effects of corrugated webs on the ultimate behavior of straight girders. But, the studies of the ultimate behavior of horizontally curved girders with corrugated webs, which generally show out-of plane behavior manly, have been rarely performed so far. By performing inelastic-nonlinear analysis, the ultimate behavior of curved girders with corrugated webs is studied in this paper. Laterally unsupported length and subtended angle of girders, and length of height of corrugation of webs are considered as the geometric parameters which would be expected to affect the ultimate behavior. By this analytical study with considering the geometric parameters, the changes of ultimate behavior and load carrying capacity of curved girders with corrugated webs are investigated. Also, the effects of corrugated webs on the increase of load carrying capacity for curved girders are studied with comparing to the capacity of general curved girders with flat webs. According to the analytical results, corrugated webs can be used to increase the ultimate load carrying capacity of curved girders, because of their high torsional and warping stiffness. But, it is also indicated that they may decrease the load carrying capacity of curved girders which have relatively small subtended angle or initial curvature, because of an accordion effect.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.4
• /
• pp.417-429
• /
• 2009

Since the introduction of the concept of osseointegration in dental implants, high long-term success rates have been achieved and accepted as viable option for the treatment of fully and partially edentulous patients. Although the use of domestic implants have increased dramatically, there are few studies on domestic implants with clinical and objective long-term data. 96 endosseous implants placed in 31 patients at Wonkwang University Sanbon Dental Hospital were examined to determine the effect of various factors on implant survival rate and marginal bone loss, through clinical and radiographic results. The design of endosseous implant used to this study is straight with the microthread.(GS II RBM Fixture) 1. 3 fixtures were lost, resulting in 96.9% cumulative survival rate. 2. Survival rate in fifties was significantly lower (93.6%) and no significant difference in marginal bone loss was found according to gender. 3. Survival rates were 95.6% in the maxillary molar area and 97.3% in the mandible molar area. 4. No significant difference in survival rate was found according to presence of bone grafts, type of prostheses, implant position, and length and diameter of implant. 5. A factor influencing marginal bone loss was presence of type of prostheses, while facters such a length, diameter of fixture and bone grafts had no statistically significant effect on crestal bone loss. This study indicates the amount of marginal bone loss around implant has maintained a relative stable during follow-up periods.

• Korean Journal of Weed Science
• /
• v.9 no.2
• /
• pp.141-148
• /
• 1989

Echinochloa species collected from 13 places of Korea appeared to be morphologically very different. They were classified by Yabuno's seed morphology method into two species such as Echinochloa oryzicola and Echinochloa crus-galli which have two varieties such E. crus-galli var, cuss-galli and var, praticola. Among them, E. oryzicola was morphologically similar to Oryza sativa, but it had small leaf length with straight from, no awn, late heading and little interspecific variance. As compared with E. oryzicola, E. eras-galli var. crus-galli, and var, praticola showed a great variance exerting so difficulty in classifing them morphologically, particularly a great variance in leaf length, tiller number and grain size. E. oryzicola species showed the more sensitive response to butachor and thiobencarb herbicides than E. eras-galli var. praticola and var. eras-galli. However, E. eras-galli var. praticola was themore sensitive one to pretilachloa herbicide than such as E. oryzicola and E. eras-galli var. eras-galli, indicating that Echinochloa species might have a selective response to the annual herbicides tested.

• Journal of Korean Society of Transportation
• /
• v.20 no.7
• /
• pp.95-105
• /
• 2002

Under a specific roadway alignment condition by design-speed standards, safety of the roadway is determined by an actual operating speed of a driver. This research takes first lanes of four-lane(hi-direction) rural highways as target facility. It also takes the straight and curved lanes of the selected highways for in-depth study. This study used NC-97 to detect speeds of passenger cars whose speeds are not affected by front vehicles. This research analyzed properties of 85th percentile operating speed at upstream of horizontal and through curves under various alignment conditions. The results show that 53∼65 Percent of drivers drive faster than the posted speed-limit (80KPH) by 14∼20 KPH on average. It also shows that the 85th-percentile operating speeds are the lowest at the middle point of curve length when curve radius is smaller. However, they are lowest at 1/4 point of curve length when curve radius is greater. Along roadways where curve radius is small, difference between upstream speed and the speed along the curve is considerably large. On the other hand. the speed difference is setting smaller as the curve radius is increasing. According to the results, significant variables affecting the 85th percentile operating speeds are curve radius and the 85th-Percentile operating speeds of upstream curves.

• Korean Journal of Veterinary Research
• /
• v.30 no.1
• /
• pp.1-8
• /
• 1990

The present study was focussed mainly on the morphological changes of the glandular tubules in the large intestine according to age of piglets. Samples were taken from large intesine of 1-, 10-, 20-, 35- and 45-day-old piglets, 2 to 3 piglets in each age group. The intestinal samples were fixed in 10% neutral formalin solution, dehydrated, and then paraffin sections were stained with H-E. The results observed were summarized as follows: 1. The mucosal glands in the cecum and colon tend to be unbranched simple straight tubular glands, or often two or more branched simple stright tubular glands. 2. The number of the longitudinal folds and the number of the crypts per cross section of piglet colons, respectively, were 1-day-old piglets-$3.8{\pm}0.8$, $92.1{\pm}6.9$; 10-day-old piglets-$7.1{\pm}1.1$, $164.2{\pm}10.3$; 20-day-old piglets-$15.2{\pm}0.8$, $178.5{\pm}6.8$; 35-day-old piglets-$19.3{\pm}3.0$, $454.9{\pm}25.3$; 45-day-old piglets-$20.6{\pm}3.1$, $524.6{\pm}37.2$, and the regression equation between age and these two number were $\hat{Y}=0.40X+4.32$ and $\hat{Y}=10.4X+51.52$, respectively. 3. The length and cell number per single side wall of a glandular tubule in the colon section were 1-day-old piglets-$196.3{\pm}7.1{\mu}m$, $40.0{\pm}3.3$; 10-day-old piglets-$236.0{\pm}34.5{\mu}m$, $47.9{\pm}5.3$; 20-day-old piglets-$262.8{\pm}39.6{\mu}m$, $54.3{\pm}9.0$; 35-day-old piglets-$291.75{\pm}48.3{\mu}m$, $56.9{\pm}4.9$; 45-day-old piglets-$364.8{\pm}61.5{\mu}m$, $67.7{\pm}7.4$, respectively, and the regression equation between age and these two data were $\hat{Y}=3.45X+193.8$ and $\hat{Y}=0.56X+41.0$, respectively. 4. The overall percentages of the cell number and length of glandular tubules in piglet colons were the pit and isthmus-$75.3{\pm}11.1%$, $78.8{\pm}12.3%$; gland-$24.7{\pm}5.4%$, $21.2{\pm}5.3%$, respectively. 5. The length and cell number of single side wall of glandular tubules in cecal sections were 1-day-old piglets-$190.3{\pm}31.1{\mu}m$, $37.6{\pm}4.8$; 10-day-old piglets-$235.6{\pm}25.3{\mu}m$, $46.2{\pm}3.6$; 20-day-old piglets-$295.3{\pm}45.6{\mu}m$, $52.0{\pm}6.2$; 35-day-old piglets-$351.3{\pm}28.3{\mu}m$, $60.4{\pm}8.5$; 45-day-old piglets-$366.3{\pm}48.5{\mu}m$, $64.7{\pm}8.2$, respectively, and the regression equation between age and these two data were $\hat{Y}=4.11X+196.6$ and $\hat{Y}=0.60X+38.9$, respectively.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.28 no.1
• /
• pp.41-57
• /
• 1983

The effect of temperature 'during the reduction division stage on the Indica-Japonica rice varieties were studied in artificial temperature-controlled cabinets (Bioclimatic Laboratory). Varieties used were indica-japonica crosses (Suweon 264, Suweon 258, Milyang 29), indica (IR36, Lengkwang) and japonica rice (Jin-heung). The results obtained from this study are summarized as follows. The most sensitive stage to low temperature, the tetrad stage, was observed in each variety with the following auricle distance: Jinheung, -12cm; IR36, -3cm; Suweon264, -9cm; Suweon258, -3cm; Milyang29, -6cm and Lengkwang, +1cm. The tetrad stage occured when the palea elongation was about 50 to 60% of the final palea length at flowering stage in all varieties. The percentage of degenerated spikelets at tetrad as influenced by low-temperature treatment was very low in Jinheung and Lengkwang, but very high in IR36. In indica-japonica crosses only the 7-days treatments had a very high percentage. Between the 4-day and 7-day treatments as well as among all varieties, clear differences were observed in the low temperature induced sterility of 'special spikelets' (upper position grains at tetrad). In the 7-day treatments except in Lengkwang, all varieties showed very high sterility. It appears that the treatments is over the critical limit for treatment. However in the 4-day treatments, the intervarietal differences in sterility were very clear. In Jinheung, sterility was 46.8%; IR36, 67.6%; Suweon264, 60.9%, Milyang29, 62.2%; Lengkwang, 27.8%. A close relationship was observed between fertility and auricle distance. The lowest fertility of special spikelets was at the tetrad stage and the first contraction phase. Before and after the stage there was an increase in fertility. The palea length elongated nearly in a straight line from the spikelet formation stage to flowering. And there was a high correlation between palea length and auricle distance. distance.