• Journal of the korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.24-39
• /
• 1982

It has already been known that quenching effect is influenced greatly by stirring and changing coolant's temperature on quenching. But according to the past investigations its effect has not been taken into consideration quantitatively in the cooling process. The purpose of this study is that the influence of flow rate and temperature on the quenching effect of cooling water as quenching medium is quantitatively examined by using the open channel. The stream of water in this study is turbulent flow. The temperature of the specimen made of pure copper is measured by CA thermocouple in the vicinity of the surface and recorded by an automatic recorder during the quenching process in city water. The results obtained are as follows; 1. The quenching effect of cooling water generally increases with Reynolds Number(characteristic length; specimen diameter)as shown in the experimental formula; but at the realm of Reynolds Number from 1.2 * 10$^{4}$ to 9.2 * 10$^{4}$, the increasing rate of quenching effect shows little increase. 2. The increasing rate of quenching effect was increased under the flow rate of 221 cm/sec. On the other hand, it was decreased below this flow rate. 3. The quenching effect was influenced by the water temperature and the flow rate. But it was rather dependent upon the former than the latter. 4. Although the quenching effect appeared loosely in the water temperature of 50.deg. C, it was shown that the quenching effect increased in the low flow rate of 31 cm/sec. comparing with the still water. 5. It is desirable to design the quenching system to be over 1.2 * 10$^{4}$ in Reynolds Number or over, 3000$cm^{-1}$ / in V/v in order to increase the quenching effect of the system using open channel.annel.

• Journal of the Korean Solar Energy Society
• /
• v.26 no.2
• /
• pp.19-25
• /
• 2006

Methane hydrate, non-polluting new energy resource, satisfies requirement and considered as a precious resource that can prevent the global warming. Fortunately, there are abundant resources of methane hydrate distribute in the earth widely. Therefore, developing the techniques that can utilize these gases effectively is highly desired. The work in this paper here is to develop a skill which can transport and store methane hydrate. As a first step, the equilibrium experiment was carried out by increasing temperatures in the cell at fixed pressures. The influence of gas consumption rates under variable degree of subcooling, stirring and water injection has been investigated formation to clarify kinetic characteristics of the hydrate. The results of present investigation showed that the enhancements of the hydrate formation in terms of the gas/water ratio are closely related to operational pressure, temperature, degrees of subcooling, and water injection.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3045-3049
• /
• 2007

This paper presents a numerical study to enhance the mixing of polyurethane resin in a container. In general, the properties of polyurethane resin vary with the production environment, such as temperature. However in this study we assumed that the dynamic viscosity of the polyurethane is kept constant at 15 [Pa s]. We computed the flow solution and visualized the mixing pattern for different shapes of mixers by using commercial code, ANSYS CFX. In order to quantify mixing, we employed the concept of mixing index by volume integration.

• Korean Chemical Engineering Research
• /
• v.55 no.5
• /
• pp.685-689
• /
• 2017

We studied the removal of zinc ions from synthetic brackish water by an adsorption method using natural Algerian Bentonite (NAB). The effect of the main physico chemical parameters-contact time, pH, temperature, ionic strength, clay weight and initial metal ion concentrations on the removal of $Zn^{+2}$-were investigated. The results showed that equilibrium was attained within 10 min of stirring time. The retention capacity of $Zn^{+2}$ increased with the increase of pH, the adsorbent dose and ionic strength. A modelization study showed that the adsorption follows Langmuir isotherm, while its kinetics was pseudo-second-order. Based on the results, it was concluded that NAB, which is natural and available, could be used as an alternative for the removal of zinc from saline aqueous solutions.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.60-63
• /
• 2003

Semi-solid forming is the process of stirring alloy during solidification, making the mixture of liquid and solid, solidifying it, reheating it to the solid-liquid coexistent temperature, and then injecting this semi solid slurry into dies. In the semi-solid die casting process, it is very important to find out the correlation of injection condition, microstructure and mechanical properties. Especially, an improper injection condition is the main cause of liquid segregation and non-homogeneous mechanical properties due to the difference of solid fraction according to the position of the products. To ensure the database requisite to the semi-solid die casting product, it is essential to acquire the mechanical properties considering liquid segregation to the injection condition. In this study, the effect of injection condition on liquid segregation, formability, microstructure and mechanical properties in a thin product was investigated.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.1
• /
• pp.62-69
• /
• 1999

In this study, the synthesis of PZT powder by bubble column reactor was investigated at various reaction conditions. As a result, the volume % of $NH_3$ gas used as a precipitator had no effect on the synthesis, but the more research is needed to control particle size.As a carrier gas, Ar, $O_2$ and air only increased the stirring effect but had no effect chemically on the synthesis. The calcination temperature of prepared PZT powder was about $500-600^{\circ}C$ and the meanparticle size of synthesized PZT powder was about $0.17{\mu}m$. The grain size of sintered body is about $0.5~3{\mu}m$ and this is similar with the value of commercial products.

• Textile Coloration and Finishing
• /
• v.15 no.6
• /
• pp.39-46
• /
• 2003

The experiments about dyeing concentration, temperature and time were done using yellow, red and purple loess as natural inorganic dyes in order to verify a degree of dyeing, characteristics of color and fastness. The results were as following; 1. As a result of analyzing components of loess, purple loess was much than other loess in quartz component and coarse particles contained. This affected to the degree of dyeing. 2. The stronger dyeing concentration was, the more the degree of dyeing was improved, and yellow loess containing fine particles was the best in the degree of dyeing. 3. When it was dyed with raising up to $100^\circ{C}$ for 10 minutes after stirring for 20 minutes at $60^\circ{C}$, was better than on starting at $40^\circ{C}$ or $80^\circ{C}$ in the degree of dyeing. Also yellow loess was the best in these experiments. 4. Washing fastness of loess was low such as other natural dyes, but dyeing wasn't transferred to other textiles. On the other hand, light fastness of it was very excellent and rubbing fastness was relatively good as 3~3.5.

• Journal of Powder Materials
• /
• v.4 no.2
• /
• pp.106-112
• /
• 1997

$Cu-Al_20_3 $ composite powders were prepared by hydrogen reduction of $Cu^{2+}$ from ammoniacal copper sulfate solution on alumina core using autoclave. The copper reduction rate and the properties of copper layer were investigated using Scanning Electron Microscope(SEM), X-ray diffractometer, size and chemical analyzers. The reduction rate of $Cu^{2+}$ showed the maximum value when the molar ratio of [$NH_3$]/[$Cu^{2+}$] was 2. In order to prevent the agglomeration of Cu powder and ethane reduction rate, $Fe^{2+}$ and anthraquinone which act as catalysis were added in the solution. Catalysis was effectively chanced with the addition of two elemerts at a time. Optimum conditions obtained in this study were hydrogen reduction temperature of 205$^{\cire}C$, stirring speed of 500 rpm and hydrogen partial pressure of 300 psi. Obtained $Cu-Al_20_3 $ composite Powders were found to have the uniform and continuous copper coating layer of nodule shape with 3~5 $\mu$m thickness.

• Journal of Microbiology and Biotechnology
• /
• v.2 no.2
• /
• pp.108-114
• /
• 1992

The fermentative characteristics in ethanol production from lactose, with increased ethanol tolerance, of a fusant yeast strain constructed by protoplast fusion of Saccharomyces cerevisiae and Kluyveromyces fragilis were studied. The ethanol tolerance of this strain was increased to 8.0%, compared with the parent K. fragilis. During batch ethanol fermentation the optimal cultivation conditions for this fusant yeast were an initial pH of 4.5, a culture temperature $30^\circ{C}$. stirring at 100 rpm without aeration in 10% lactose medium (supplied with 1.0% yeast extract). Using this fusant strain in whey fermentation to ethanol, maximum ethanol production reached 3.41% (w/v) (theoretical yield; 66.7%) after a 48 hour cultivation period.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.362-370
• /
• 1996

Kalsilite (KAlSiO4) system undergoes a displacive phase transition from hexagonal phase with p63 space group to the phase with P63mc at 886$^{\circ}C$. The flux composition having kalsilite :K2O:B2O3=1:2:2 has enabled the growth of hexagonal kalsilite with the size of 0.5~1 mm at a slow cooling rate (0.3$^{\circ}C$/hr). On decreasing the cooling rate the size has increased and pyramidal (1011) faces are newly developed with the shape of (0001) and (1010) faces. Upon stirring (1011) faces are degraded. The space group of O1 and O2 are P21221 and C2221 respectively. Their orthorombic modification O1 and O2 are synthesized at relatively low and high temperature respectively.