• Journal of Environmental Health Sciences
• /
• v.27 no.3
• /
• pp.21-26
• /
• 2001

This study was performed to define the physicochemical characteristics of food waste and food wastewater, and to find the effect of salinity variation experiment, the samples of 1, 2, 3 and 4 were prepared by the salinity of 1.0%, 1.5%, 2.0% and 2.5%, respectively. In experiment, aerobic composting reactors were operated by the model which was composed of half an hour's stirring and 2 hour's aeration per day, for 45 days. Seeds of vegetables of Chinese cabbage and red pepper were seeded at compost-free control, compost 1, 2, 3 and compost 4 for the sake of investigation of germination rate and growth rate of those. The followings are the conclusions that were derived from this study. 1. In food waste, the moisture content was 60%, organic compound content was 95%, total carbon was 47.5%, total nitrogen was 1.6%(therefore, C/N ratio was 30). The values of pH were 4.0 and 3.8 the values of salinity were 0.9% and 1.2%, and the values of conductivity were 7.8 mS/cm and 18.0 mS/cm, respectively. 2. In salinity experiment, the reduction rate of volume was increased(40%) when the salinity was decreased(1.0%). Also, the reduction rate of mass was increased(52%) when the salinity was decreased(1.0%). This fact denotes that salinity hinders the process of composting. 3. Germination rate and growth rate of Chinese cabbage are more excellent than those of red pepper(97.14%, 5.2:2.5 cm). 4. In Chinese cabbage, germination rate and growth rate at compost with the lowest salinity are more excellent than those at compost-free control(97:94%, 5.2:4.5 cm).

• Journal of the Korean Chemical Society
• /
• v.37 no.5
• /
• pp.477-482
• /
• 1993

The determination of trace level mercury in bio-materials has been investigated by the square wave anodic stripping voltammetry (ASV)-technique at glassy carbon electrode. Prior to analysis, the bio-materials were digested with HNO3/H2SO4 mixture and KMnO4 was added to complete the oxidation. The detection limit of the mercury varied greatly with deposition time, deposition potential, pH and stirring rate. When deposition is carried out for 240 sec with 400 rpm stirring at -1.0 volts vs. Ag/AgCl, the detection limit was below $0.5\;ppb\;(2.5{\times}10^{-9} M)$. The method is recommended for trace level mercury analysis of biomaterials because this procedure is time saving and has higher sensitivity.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.326-334
• /
• 2002

The purpose of this work was the producing of a biodegradable poly($\varepsilon$-caprolactone) (PCL) microcapsule and the analyzing of form and features for the manufacturing conditions which could be observed in a prospective drug delivery systems (DDS) through drug release. The effects of different stirring rates, stirring times and concentrations of emulsifier for the diameter and form of the microcapsules were observed using image analyzer (IA) and scanning electron microscopy (SEM). As a result, the microcapsules were made in wrinkle and spherical forms with a mean particle size of 40~300$\pm$20 $mu extrm{m}$. PCL microcapsules containing drugs were confirmed using FT-IR spectra. The role of interfacial adhesion between PCL and drug was determined by contact angle measurements. The drug release test of PCL microcapsules was characterized by UV/vis. spectra. It was found that the drug release rate of the microcapsules prepared with high concentration emulsifier was significantly fast.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.511-516
• /
• 2005

In this work, the crosslinked-chitosan microcapsules containing fragrant oil were prepared by oil-in-water-in-oil (O/W/O) multi-emulsion method. The effects of concentration of fragrant oil and stirring rates on the preparing of the microcapsules were investigated. The diameter and form of the microcapsules were observed by scanning electron microscope (SEM). As a result, the average particle size of microcapsules was decreased with increasing the stirring rate. The formation of chitosan microcapsules was comfirmed by FT-IR. The inclusion of fragrant oil into chitosan microcapsules was determined in the presence of specific peak of fragrant oil, i.e., $1,460cm^{-1}$, $2,960cm^{-1}$. Also, the release behavior or profile of fragrant oil from chitosan microcapsules was examined with UV/vis spectra. Released amounts of fragrant oil were increased with increasing as the content of fragrant oil and decreasing the pH.

• Journal of the Korean Chemical Society
• /
• v.45 no.4
• /
• pp.298-303
• /
• 2001

The trace-level mercury in bio-materials has been determinated by the anodic stripping square wave voltammetry (ASSWV)-technique at glassy carbon electrode. Prior to the analysis, the bio-materials were digested with $HNO_3/H_2SO_4$ mixture and KMnO4 was added to complete an oxidation process of the mixture. The detection limit of the mercury varied greatly with deposition time, deposition potential, pH and stirring rate. When the deposition was carried out for 240 sec on 400 rpm stirring at -1.0 volts vs. Ag/AgCl, the detection limit was below 0.5 ppb ($2.5{\times}10^{-9}M$). The accumulated mercury was high in the kidney and liver, and low in the brain according to the determination of mercury accumulation for a white rat by this method.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.5
• /
• pp.82-88
• /
• 2013

There are the stirring test and drain test in the daily performance test to determine the thermal performance of a domestic solar hot water system. The drain test is a test that measures the discharge heating rate while drain the hot water from the top of the storage tank and supply the city water to the bottom of the tank. From the perspective of the user, this drain test is more effective than the stirring test. In this study, the thermal performance were compared through the drain test for a passive type and an active type domestic solar hot water systems consisting of the same storage tank and collectors. At this point, a passive type was used the horizontal storage tanks, and an active type was used vertical storage tank. In the drain test, when the hot water drained up to the reference hot water temperature, an active type which have vertical storage tank represents excellent daily performance than a passive type which have horizontal storage tank regardless of weather conditions. The reason for this is because the vertical storage tank is advantageous to thermal stratification in the tank. After the drain test, the residual heat for the horizontal storage tank was much more than the vertical storage tank, but in the next day the amount of discharged heat were less than the those of vertical storage tank neither. Thus, the solar water heating system which have horizontal storage tank should be adopted preheating control method rather than separate using control method when connected with auxiliary heat source device.

• Journal of Surface Science and Engineering
• /
• v.45 no.5
• /
• pp.181-187
• /
• 2012

The Friction Stir Welding (FSW) has mainly been used for making butt joints in Al alloys. The development of Friction Stir Lap Welding (FSLW) would expand the number of applications. In this study, microstructures and mechanical properties of FSLW in A5052 alloy were investigated under varying rotating speed and probe length. Investigating the characteristics as FSLWed conditions were as below ; Failure Maximum load by shear fracture was increased proportional to the width of joint area, which was increased by input heat, stirring intensity in the case of 2.3 mm probe length. Tensile fracture occurred, and maximum load was determined due to side worm hole of joint area and softening of microstructure in the case of 3.0 mm probe length. In the case of 3.7 mm probe length, material hook and bottom worm hole were appeared at the end interface of joint area. The most sound FSLW condition with no defects was 3.0 mm probe length and 1500 rpm-100 mm/min. No defects were showed in 1500 rpm-100 mm/min and 1800 rpm-100 mm/min, but Vickers microhardness distribution in TMAZ/HAZ which was fracture zone was lower in 1800 rpm-100 mm/min than in 1500 rpm-100 mm/min. In this condition highest tensile strength, 215 MPa (allowable rate 78% of joint efficient) was obtained.

• Nuclear Engineering and Technology
• /
• v.55 no.1
• /
• pp.63-70
• /
• 2023

Ultrasound-assisted dissolution of U₃O₈ powder in carbonate solution was explored to determine if and how ultrasound act during the dissolution. The variation of U₃O₈ solid particles and uranyl complexes under ultrasound treatment and magnetic stirring was observed in carbonate media. The results show that the use of ultrasound can increase the solubility and dissolution rate of U₃O₈ powder than that under magnetic stirring. The crush of U₃O₈ particles and the reduction of the activation energy (Ea, kJ/mol) of U₃O₈ dissolution reaction were observed, which both play an important role in the ultrasonic-assisted dissolution of U₃O₈ in carbonate-peroxide solution. Meanwhile, there is no observation of the ultrasound effect on the distribution of uranyl species and hydrolysis of uranyl complexes during the ultrasound treatment in carbonate-peroxide solution. Although the generation of ·OH radicals under ultrasound (22 ± 2 kHz) was observed, the oxidation of ·OH had little effect on the dissolution of U₃O₈ in the carbonate-peroxide solution system.

• Journal of the korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.24-39
• /
• 1982

It has already been known that quenching effect is influenced greatly by stirring and changing coolant's temperature on quenching. But according to the past investigations its effect has not been taken into consideration quantitatively in the cooling process. The purpose of this study is that the influence of flow rate and temperature on the quenching effect of cooling water as quenching medium is quantitatively examined by using the open channel. The stream of water in this study is turbulent flow. The temperature of the specimen made of pure copper is measured by CA thermocouple in the vicinity of the surface and recorded by an automatic recorder during the quenching process in city water. The results obtained are as follows; 1. The quenching effect of cooling water generally increases with Reynolds Number(characteristic length; specimen diameter)as shown in the experimental formula; but at the realm of Reynolds Number from 1.2 * 10$^{4}$ to 9.2 * 10$^{4}$, the increasing rate of quenching effect shows little increase. 2. The increasing rate of quenching effect was increased under the flow rate of 221 cm/sec. On the other hand, it was decreased below this flow rate. 3. The quenching effect was influenced by the water temperature and the flow rate. But it was rather dependent upon the former than the latter. 4. Although the quenching effect appeared loosely in the water temperature of 50.deg. C, it was shown that the quenching effect increased in the low flow rate of 31 cm/sec. comparing with the still water. 5. It is desirable to design the quenching system to be over 1.2 * 10$^{4}$ in Reynolds Number or over, 3000$cm^{-1}$ / in V/v in order to increase the quenching effect of the system using open channel.annel.

• Journal of the Korean Ceramic Society
• /
• v.39 no.6
• /
• pp.550-557
• /
• 2002

TiO$_2$ particles coated on fly ash composites for use in photocatalyst were synthesized by the precipitation dropping method and heated at $700^{\circ}C$ for 2 h. The pH of reaction solution, the addition rate of NH$_4$HCO$_3$, the stirring speed, the reaction temperature and the concentration of TiC1$_4$ had a pronounced effect on the nature of precipitated TiO$_2$ particles on the surface off fly ash and the crystal structure of precipitated TiO$_2$ particles. At an addition rate of NH$_4$HCO$_3$; 1.0 ml/min, the pH of the reaction solution; 6, the stirring speed; 1,000 rpm and the reaction temperature; 8$0^{\circ}C$, about 10 nm of TiO$_2$ particle size and homogeneous precipitated layer on the surface of a fly ash was achieved. On the contrary, at an addition rate of NH$_4$HCO$_3$; 0.3,0.5 ml/min, the pH of the reaction solution; 2 and 11, the stirring speed; 300~500 rpm and the reaction temperature; lower than 5$0^{\circ}C$:, Inhomogeneous precipitated layer was developed on a fly ash. TiO$_2$ particles with anatase phase was formed as-dried precipitation at the low concentration of Tic14, the high addition rate of NH$_4$HCO$_3$ and the high reaction temperature, the crystalline fraction of anatase increased with raising heat-treatment temperature and rutile phase began to formation at 80$0^{\circ}C$. The crystal size of TiO$_2$ particles increased with raising the heat-treatment temperature, the crystal size was showed about 21 m at $700^{\circ}C$. Anatase type of TiO$_2$ coated on the fly ash heated at $700^{\circ}C$ for 2 h showed 1.25 g/cm$^3$of particle density, 82.8% of strength and 69.5 Lab of whiteness and can be used as a photocatalyst.