• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.118-121
• /
• 2006

Stick-slip of belt-pulley system produces vibration which results in the noise problem. Experimental study was carried out to investigate the phenomenon of stick-slip with simple v-belt system. The optical displacement sensor detected the vibration caused by the stick-slip of which the frequency was significantly dependant on tension of the belt. The rotation speed of putties also affected the frequency and magnitude of the stick-slip vibration. Existence of misalignment between the driven and drive pulleys made some difference in the stick-slip frequency, but not much. Further study is necessary to identify the generation of noise from the stick-slip vibration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.214-215
• /
• 2009

The friction is inevitable and unpredictable phenomena, so most mechanical systems are designed to low friction effect by using bearings and lubricants. However, the slip-stick actuator applies the friction force to its movement. The slip-stick mechanism is applied the piezoelectric actuator to overcome short displacement. Fast response of piezoelectric actuator is also good characteristic for the slip-stick mechanism. However, the piezoelectric actuator with slip-stick mechanism isn't common, because its cost and driving voltage are too high. In this paper, a voice-coil actuator with slip-stick mechanism is introduced. The cost and the driving voltage of a voice-coil actuator are much less than the piezoelectric actuator. And a dynamic vibration amplifier is proposed to adjust the dynamic performance of the actuator. By the results of numerical analysis, the feasibility of a dynamic vibration amplifier is verified.

• Journal of KSNVE
• /
• v.10 no.3
• /
• pp.451-456
• /
• 2000

In this paper a discrete time model for the identification of nonlinear vibration system with stick-slip friction is proposed. The proposed model can handle the highly nonlinear behavior of the friction such as stick-slip phenomenon and Stribeck effect. The basic idea of the proposed model is as follows : If the nonlinearity of the system can be predicted as a simple function then this nonlinear function term cab be directly used in the discrete time model. By doing this the number of nonlinear terms in the model can be much less than those of NARMAX model which is widely used nonlinear discrete model. The simulation result shows that the proposed model can estimate the response of the nonlinear vibration system with stick-slip friction very well with less computational effort.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.250-251
• /
• 2014

This paper investigates the stick-slip phenomena on spinning shaft. The modeling of the shaft is considered only torsional direction with nonlinear friction. The friction is adopted a negative friction-velocity slope. Based on the model, a nonlinear equation of motion is derived and analyze the stick-slip phenomena. In order to analyze the time dependent response, the nonlinear formulations are numerically solved by nonlinear Newmark method. The numerical results reveal the stick-slip phenomena on the spinning shaft system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.830-832
• /
• 2014

In this study, friction stick-slip vibration're interpretation of the phenomenon, we used a statistical model of friction. In a previous study using a definite friction factor, but to a dynamic simulation using a constantly changing during the integration time by a Monte Carlo simulation method, not the average coefficient of friction and the dynamic friction coefficient and a constant value in this study.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.1
• /
• pp.49-59
• /
• 2024

Recently, the electric vehicle market is gradually growing due to strengthened environmental regulations and high oil prices. also, in internal combustion engine vehicles, the sensitivity of Buzz, Squeak, Rattle (BSR) noise is increasing as engine Noise, Vibration, and Harshness (NVH)-related noise is reduced and technology for shielding noise coming from outside is developed. In this study, the stick-slip noise that occurs in Panoramic Curved Display (PCD) of automobile was analyzed for the correlation between the surface energy of polymer plastic and the polar component. For polar polymer materials, Acrylonitrile Butadiene Styrene (ABS) and PolyCarbonate-Acrylonitrile Butadiene Styrene (PC-ABS), compound materials were fabricated and evaluated. As a result, when the polar component of the polymer plastic was 3.86 mN/m or higher, stick-slip motion occurred, and as the absolute transition slope increased in the friction behavior over time, the possibility of stick-slip noise increased and the value of the friction coefficient The greater the difference, the greater the strength of the stick-slip noise.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.296-303
• /
• 2002

Tribology, in other words, interacting surfaces in relative motion, is essential in life. The relative motion on surfaces may cause some problems with heat, vibration, noise, and so on. Unwanted vibrations by friction, which may arise during the operation of machines, are costly in terms of reduction of performance and service life. All these phenomena inolve stick-slip. The telescopic boom operations involves stick-slip oscillations like slideways. Unwanted stick-slip oscillations on telescopic boom operations cannot achieve smooth sliding and many developers of that machine makes a lot of effort to remove or reduce it. So this paper presents stick-slip oscillation with pressure of the hydraulic cylinder which drives booms, and attempts a theoretical approach for the numerical analysis for its stick-slip condition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.4
• /
• pp.19-29
• /
• 1995

This paper discusses the stick-slip phenomenon of the driveline system of a vehicle in consideration of friction. Friction is operated on the between of flywheel and clutch disk. The expressions for obtaining the results have been derived from the equation of motion of a three degree of freedom frictional torsion vibration system which is made up driving part(engine, flywheel), driven part(clutch, transmission) and dynamic load part(vehicle body) by applying forth-order Rungekutta method. It was found that the great affect parameters of the stick-slip or stick motion were surface pressure force between flywheel and clutch disk, time decay parameter of surface pressure force and 1st torsional spring constant of clutch disk when driveline system had been affected by friction force. The results of this study can be used as basic design data of the clutch system for the ride quality improvement of a car.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.230-236
• /
• 2008

In this paper, a model-based stick-slip compensation for the micro-positioning is proposed using an enhanced stick-slip model based on statistical rough surface contact model. The smart structure is comprised with PZT (lead (Pb) zirconia (Zr) Titanate (Ti)) based stack actuator incorporating with the PID (Proportional-Integral-Derivative) control algorithm, mechanical displacement amplifier and positioning devices. For the stick-slip compensation, the elastic-plastic static friction model is used considering the elastic-plastic asperity contact in the rough surfaces statistically. Mathematical model of system for the positioning apparatus was derived from the dynamic behaviors of structural parts. PID feedback control algorithms with the developed stick-slip model as well as feedforward friction compensator are formulated for achieving the accurate positioning performance. Experimental results are provided to show the performances of friction control using the developed positioning apparatus.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.11
• /
• pp.1134-1142
• /
• 2008

In this paper, a model-based stick-slip compensation for the micro-positioning is proposed using an enhanced stick-slip model based on statistical rough surface contact model. The smart structure is comprised with PZT(lead (Pb) zirconia(Zr) Titanate(Ti)) based stack actuator incorporating with the PID(proportional-integral-derivative) control algorithm, mechanical displacement amplifier and positioning devices. For the stick-slip compensation, the elastic-plastic static friction model is used considering the elastic-plastic asperity contact in the rough surfaces statistically. Mathematical model of system for the positioning apparatus was derived from the dynamic behaviors of structural parts. PID feedback control algorithms with the developed stick-slip model as well as feedforward friction compensator are formulated for achieving the accurate positioning performance. Experimental results are provided to show the performances of friction control using the developed positioning apparatus.