• 한국공간구조학회논문집
• /
• 제8권5호
• /
• pp.83-93
• /
• 2008

국민소득수준의 향상에 따라 국내 건축물의 디자인 및 사용목적의 대한 다양성이 요구되고 있다. 대공간 구조물은 이러한 시대적 요구에 적합한 구조물로서 최근 대공간 구조물에 대한 설계 및 시공법에 관한 관심이 꾸준히 증가하고 있다. 트러스구조는 대공간 구조에 보편적으로 사용되는 구조시스템으로 트러스의 부재는 단면의 효율이 높은 강관을 사용하는 것이 일반적이다. 현재 국내에 유통되고 있는 강관은 생산처에 따라 다양한 제품이 생산되고 있으나 강관 소재의 출처 및 강관 자체의 실제 성능에 관한 연구는 미비한 실정이다. 이 연구는 국내에 유통되고 있는 일반구조용 각형강관, 원형강관 및 비계용 강관에 대하여 소재의 인장시험과 Stub-column 압축시험 및 기둥의 좌굴실험을 통해 강관의 소재성능 및 구조부재로서의 압축성능을 파악하는 것을 목적으로 한다. 소재시험결과, 구입처 구분 및 단면형상에 따른 강관 소재성능의 편차가 확인되었다. 기둥좌굴 실험결과, 각 실험체의 압축내력은 LSD 기준곡선에 만족하는 결과를 나타내었으며, SSRC 곡선1, ECCS-a곡선에 상회하는 결과를 나타내었다.

• 한국표면공학회지
• /
• 제54권5호
• /
• pp.248-259
• /
• 2021

This study examined the influence of post weld heat treatment (PWHT) conditions on corrosion behaviors of laser-welded super duplex stainless steel tube. Due to the high cooling rate of laser welding, the phase fraction of ferrite and austenite in the weld metal became unbalanced significantly. In addition, the Cr₂N particles were precipitated adjacent to the fusion line, which can be susceptible to the localized corrosion. On the other hand, the phase fraction in the weld metal was restored at a ratio of 5:5 when exposed to temperatures above 1060 ℃ during the post weld heat treatment. Nevertheless, the high beltline speed during the PWHT, leading to the insufficient cooling rate, caused a precipitation of σ phase at the interface between ferrite/austenite in both weld metal and base metal. This resulted in the severe corrosion damages and significant decrease in critical pitting temperature (CPT), which was even lower than that measured in as-welded condition. Moreover, the fraction of σ phase in the center region of post weld heat treated steel tube was obtained to be higher than in the surface region. These results suggest that the PWHT conditions for the steel tube should be optimized to ensure the high corrosion resistance by excluding the precipitation of σ phase even in center region.

• Steel and Composite Structures
• /
• 제38권1호
• /
• pp.17-31
• /
• 2021

Post-earthquake fire is a common disaster which causes serious safety issues to infrastructures. This study aims to investigate the residual loading capacities of circular concrete-filled steel tube (CFST) columns under post-earthquake fire experimentally and numerically. The experimental programme contains two loading steps - pre-damage cyclic loading at room temperature and transient state tests with constant compression loads. Three finite element models are developed and validated against the test results. Upon validation, a total of 48 numerical results were generated in the parametric study to investigate the effects of thickness and strengths of steel tube, axial compression ratio and damage degree on the fire resistance of circular CFST columns. Based on the analysis on experimental and numerical results, the loading mechanism of circular CFST columns is discussed. A design method is proposed for the prediction of fire resistance time under different seismic pre-damage and compression loads. The predictions by the new method is compared with the newly generated experimental and numerical results and is found to be accurate and consistent with the mean value close to the unity and a coefficient of variation around 1%.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.244-248
• /
• 2003

Recently social demands of fuel economy and environmental regulations require the development of light materials and new manufacturing technologies. In this point, the aluminum tube hydroforming process which is satisfied with good strength-to-weight ratio and recyclability is innovative concept. However the level of the aluminum tube hydroforming technology is low in comparison with that of steel tube hydroforming. In this paper, the hydroformability of aluminum tubes in different heat treatments is presented. Theoretical results for forming limits of the wrinkling and bursting are compared with experimental results of aluminum tubes.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.458-461
• /
• 2004

The column for Steel Framed Reinforced Concrete Structure (SFRCS) and the column for Reinforced Concrete Structure (RCS) could be the most common building structure. The increasing of the need for massive space hasaffected the size of building components for supporting the massive structure. However, the changing of components size makes inefficient space of building. Hence. to meet the need for acquiring efficient space comparing the budget and cost the new structure method, Concrete Filled Tube Steel (CFT), was developed. CFT is the structure for which steel tube instead of other materials such as wood for holding concrete is used. The most benefit of this one is to help in reducing the size of the building components and local buckling because of tube steel holding concrete. For this reason, this research will examine the probability of applying CFT on construction sites by using the concrete $(800kg/cm^2)$ especially for CFT through the data from the real size mock-up.

• Steel and Composite Structures
• /
• 제15권6호
• /
• pp.679-703
• /
• 2013

This paper presents experimental investigations of the fundamental behavior of concrete filled steel tube (CFT) beam-columns under fire loading. A total of thirteen specimens were tested to determine the axial force-moment-curvature-temperature behavior of CFT beam-columns. The experimental approach involved the use of: (a) innovative heating and control equipment to apply thermal loading and (b) digital image correlation with close-range photogrammetry to measure the deformations (e.g., curvature) of the heated region. Each specimen was sequentially subjected to: (i) constant axial loading; (ii) thermal loading in the expected plastic hinge region following the ASTM E119 temperature-time T-t curve; and (iii) monotonically increasing flexural loading. The effects of various parameters on the strength and stiffness of CFT beam-columns were evaluated. The parameters considered were the steel tube width, width-tothickness ratio, concrete strength, maximum surface temperature of the steel tube, and the axial load level on the composite CFT section. The experimental results provide knowledge of the fundamental behavior of composite CFT beam-columns, and can be used to calibrate analytical models or macro finite element models developed for predicting behavior of CFT members and frames under fire loading.

• 한국강구조학회 논문집
• /
• 제18권5호
• /
• pp.625-631
• /
• 2006

구조재의 잔류응력(residual stress)은 외부에서 하중이 작용하지 않는 상태에서도 구조물 내부에 존재하는 응력으로 건설현장에서 구조물을 설치, 조립하는 경우에 발생하게 되며 특히 용접이나 과부하에 의한 구조물의 설치 후에도 발생할 수 있다. 이에 본 연구에서는 600MPa급 mega structure용 강관제작 상의 프레스 및 용접에 의한 잔류응력의 영향을 파악하고자 홀드릴링 변형게이지법(Hole-Drilling Strain Gage Method)을 이용하여 용접선 부근을 중심으로 총 59개소를 측정하여 잔류응력의 분포 및 크기를 평가하였다.

• Steel and Composite Structures
• /
• 제10권3호
• /
• pp.261-279
• /
• 2010

Generally, a box tube, which is used for an existing square CFT structure, is made by welding four plates. The manufacturing efficiency of this steel tube is poor, and it also needs special welding technology to weld its internal diaphragm and the through diaphragm. Therefore, an interior-anchor-type square steel tube was developed using the method of cold-forming thin plates to prevent welding of the stress concentration position, and to maximize the section efficiency. And, considering of the flow of beam flange load, the efficiency of erection and the weldability of the diaphragm to thin walled steel column, the external diaphragm connection was selected as the suitable type for the welded built-up square CFT column to beam connection. And, an analytical study and tests were conducted to evaluate the structural performance of the suggested connection details and to verify the suggested equations for the connection details. Through this study, the composite effect of the internal anchor to concrete, the resistance and stress distribution of the connections before and after the existing column is welded to the beam, the effective location of welding in connection were analyzed.

• Steel and Composite Structures
• /
• 제38권5호
• /
• pp.547-562
• /
• 2021

This paper aims to explore the mechanical behavior and moment-rotation model of blind bolted joints between concrete-filled double skin steel tubular columns and steel-concrete composite beams. For this type of joint, the inner tube and sandwiched concrete were additionally identified as basic components compared with CFST blind bolted joint. A modified moment-rotation model for this type of connection was developed, of which the compatibility condition and mechanical equilibrium were employed to determine the internal forces of basic components and neutral axis. Following this, load transfer mechanism among the inner tube, sandwiched concrete and outer tube was discussed to assert the action area of the components. Subsequently, assembly processes of basic coefficients in terms of their stiffness and resistances based on the component method by simplifying them as assemblages of springs in series or in parallel. Finally, an experimental investigation on four substructure joints with CFDST columns for validation purposes was carried out to capture the connection details. The predicted results derived from the mechanical models coincided well with the experimental results. It is demonstrated that the proposed mechanical model is capable of evaluating the complete moment-rotation relationships of blind bolted CFDST column composite connections.

• Structural Engineering and Mechanics
• /
• 제49권3호
• /
• pp.297-309
• /
• 2014

Under lateral loads Framed Tube (FT) system exhibits reduction of cantilever efficiency due to the effect of shear lag. Braced Tube (BT) represents a valuable solution to overcome shear lag problems by stiffening the exterior frame with diagonal braced members. This study investigates the effect of shear lag on BT and FT under wind load. Shear lag and top-level displacement results are compared with previous findings by researchers on FT and BT systems. The investigation of the effect of various configurations in BT on the reduction the shear lag is another objective of this study. The efficiency of each structure is evaluated using the linear response spectrum analysis to obtain shear lag. STADD Pro software is used to run the dynamic analysis of the models. Results show there is relatively less shear lag in all the BT configurations compared to the FT structural system. Moreover, the comparison of the obtained result with those derived by previous studies shows that shear lag is not proportional to lateral displacement. With respect to results, optimum BT configuration in term of lower shear lag caused by lateral loads is presented.