• 대한금속재료학회지
• /
• 제46권3호
• /
• pp.150-158
• /
• 2008

The temperature distribution of high speed tool steel rod has been studied during high speed hot rolling procedures. The tool steel rod shows severe temperature gradient during rolling procedures and the temperature at the center of rod are much higher than that at the surface of rod. This temperature gradient accumulated after every rolling procedure and the center of rolled rod could be remelt in some procedures to cause inside defects. In this study, the temperature distribution was simulated using finite element method and the processing parameters such as rolling speed, cooling condition, have been discussed to prevent the temperature increases at the center of rod.

• Journal of Mechanical Science and Technology
• /
• 제16권4호
• /
• pp.501-511
• /
• 2002

This paper presents a study of the effect of rolling temperature, roll gap (pass height), initial specimen size and steel grades of specimens on the roll force in round-oval-round pass sequence by applying approximate method and verifications through single stand pilot rod rolling tests. The results show that the predicted roll forces are in good agreement with the experimentally measured ones. The approximate model is independent of the change of roll gap, specimen size and temperature. Thus, the generality of the prediction methodology employed in the approximate model is proven. This study also demonstrates that Shida's constitutive equation employed in the approximate model needs to be corrected somehow to be applicable for the medium and high carbon steels in a lower temperature interval (700∼900$\^{C}$).

• 한국공간구조학회논문집
• /
• 제23권4호
• /
• pp.51-58
• /
• 2023

In this study, the displacement dependence, strength, and energy dissipation capacity of the steel rod damper were evaluated. The test variables are the number of steel rod dampers and the lateral deformation prevention details. From test results, it was evaluated that the displacement dependence conditions in the structural design code were satisfied. The maximum strength and energy dissipation capacity increased linearly as the number of steel rod increased. In addition, the maximum strength and energy dissipation capacity were evaluated by more than 20 times increased by using of the lateral deformation prevention details.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.27-36
• /
• 2004

Contemporary objectives for steel rod rolling processing are increasingly complex and often contrasting i.e. obtaining a desired product with optimum combination of properties such as strength, toughness and formability at lower cost. Low-alloy steel rods have been produced with several heat treatments for drawing and forging processes at room temperature. In order to reduce these heat treatments much of the researches concerning of high temperature mechanical behavior of steel rods have been conducted at wire rod mill of POSCO. In this present work, optimizations of rolling temperature and cooling rate for JS-SCM435 are performed to eliminate softening heat treatment(Low Temperature Annealing) for drawing process. The results from the optimization changed the microstructure of rods after rod rolling from Bainite with high tensile strength of 1000Mpa to Pearlite and Ferrite with appropriate strength of 750Mpa that is equivalent tensile strength after softening heat treatment.

• 한국공간구조학회논문집
• /
• 제22권4호
• /
• pp.49-57
• /
• 2022

In this study, based on the research results of the steel plate and steel rod dampers with rocking behavior, the moment and the drift ratio were compared and evaluated. As a test result evaluation, it was showed that the behavior of R15-200 and R15-140 was very good than other dampers. And the steel rod damper showed in-plane behavior to the loading direction, and was evaluated to prevent out-of-plane behavior that causes performance degradation.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권3호
• /
• pp.12-20
• /
• 2023

본 연구에서는 영구 교좌장치가 설치되는 교량의 교각 상부에서 FCM에 의한 상부공 시공에 주로 적용하고 있는 "내부 프리스트레싱 긴장재에 의한 임시 고정시스템"에서 강봉에 도입한 긴장력의 변화와 주두부의 기울음 특성을 분석하여 안정성 확보 방안에 대한 기초자료를 제시하였다. 상기 시스템은 시공 중 불균형 모멘트에 의하여 발행하는 상향력에 저항하기 위하여 교각과 교각 상부의 PSC BOX 내부에 연직으로 강봉을 설치한 후 상부에서 인장 및 정착하기 때문에, 그 동안 강봉에 도입한 긴장력의 변화와 주두부의 기울음 정도를 확인하기 어려웠다. 따라서, 강봉의 길이 변화 및 주두부 변위에 대한 계측 및 분석은 미세 측정이 가능한 FBG 센서를 활용하여 각 세그먼트 진행의 전후에 수행하였다. 강봉의 계산 인장력과 잔존 인장력을 비교한 결과 안전율은 모든 교량에서 저하하였다. 그 원인은 주로 강봉의 정착 과정에서부터 1세그먼트 완료까지의 초기 긴장력 손실로 확인되어 이에 대한 대책을 제시하였다. 주두부의 미세 기울음 특성을 분석한 결과 안전율이 충분히 확보된 교량에서도 세그먼트의 진행에 따라 미세 기울음이 증가되는 양상을 보였으며, 세그먼트 진행 단계별로 콘크리트 타설 전,후의 차이도 뚜렸하게 확인되었다. 또한, 모든 교량에서 미세 기울음의 증가는 강봉의 긴장력 손실과 밀접한 관계를 보이며 기울음 측면과 반대 측면의 응력 감소가 더욱 크게 나타났다. 이러한 현상의 원인은 불균형모멘트에 의하여 기울음 측면과의 반대 측면의 강봉에 상향 인장력이 발생하여 강봉의 응력 차이를 유발시킨 때문으로 판단된다.

• Steel and Composite Structures
• /
• 제48권3호
• /
• pp.321-333
• /
• 2023

This paper proposes a comprehensive investigation on lateral stiffness of corner-supported steel modular frame using splice connection. A full-scale modular frame with two stacked steel modules under lateral load is tested. Ductile pattern in the transfer of lateral load is found in the final failure mode. Two types of lateral stiffness, including tangent stiffness and secant stiffness, are defined from the load-displacement due to the observed nonlinearity. The difference between these two types of stiffness is found around 20%. The comparisons between the experimental lateral stiffness and the predictions of classical methods are also conducted. The D-value method using hypothesis of independent case is a conservative option for predicting lateral stiffness, which is more recommended than method of contraflexural bending moment. Analyses on two classical short-rod models, including fix-rod model and pin-rod model, are further conducted. Results indicate that fix-rod model is more recommended than pin-rod model to simplify splice connection for simulation on lateral stiffness of modular frame in elastic design stage.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권6호
• /
• pp.1-9
• /
• 2020

본 연구에서는 벽체의 록킹 거동을 고려한 내진보강 기법을 개발하였다. 록킹 거동은 벽체 수직 축을 중심으로 좌우로 회전하는 것으로, 개발 시스템은 변위 큰 부분에 댐퍼 등을 설치하여 에너지를 소산 시키는 방법이다. 댐퍼는 강봉 댐퍼를 사용하였으며, 강봉 지름 및 길이(형상비)를 변수로 선정하였다. 실험결과 댐퍼길이 260mm 경우 우수한 내진 성능을 보유한 것으로 평가되었다.

• 한국정밀공학회지
• /
• 제13권11호
• /
• pp.124-131
• /
• 1996

The dynamic material property of Mn-B ally high-strength steel is investigated through the rod impact test which is one of simple test methods for the analysis of the material behavior under high-strain-rate. Rod impact test is performed to produce the deformed shape of rod and analyzed by the one-dimensional theory based on conservation law and the two-dimensional hydrocode AUTODYN-2D. The dynamic yield stress is determined and compared with the static yield stress to investigate the strain-rate sensitivity of Mn-B alloy high-strength steel.

• 한국공간구조학회논문집
• /
• 제15권1호
• /
• pp.47-55
• /
• 2015

This paper shows the simplified equation to predict the ultimate moment capacity and corresponding rod stress in reinforced concrete beam with external post-tensioning rods. Because the stress of external post-tensioning rod depends on the beam deflection, the previous analytical model for post-tensioned beams requires a tedious iteration process. Also, the stress equations in ACI code or other researchers' models are suitable only for internal tendons in concrete beams. In this study, given the lack of analytical approaches to predict the nominal stress of the external unbonded rod, a simple and robust equation has been proposed for externally post-tensioned concrete beams. It is concluded that the proposed equation predicted the stress of external steel rods in post-tensioned concrete beams reasonably well.