• Steel and Composite Structures
• /
• v.3 no.3
• /
• pp.185-198
• /
• 2003

The concept of performance based seismic design has been gradually accepted by the earthquake engineering profession recently, in which the cost-effectiveness criterion is one of the most important principles and more attention is paid to the structural performance at the inelastic stage. Since there are many uncertainties in seismic design, reliability analysis is a major task in performance based seismic design. However, structural reliability analysis may be very costly and time consuming because the limit state function is usually a highly nonlinear implicit function with respect to the basic design variables, especially for the complex large-scale structures for dynamic and nonlinear analysis. Understanding statistical properties of the structural inelastic deformation, which is the aim of the present paper, is helpful to develop an efficient approximate approach of reliability analysis. The present paper studies the statistical properties of the maximum elastoplastic story drift of steel frames subjected to earthquake load. The randomness of earthquake load, dead load, live load, steel elastic modulus, yield strength and structural member dimensions are considered. Possible probability distributions for the maximum story are evaluated using K-S test. The results show that the choice of the probability distribution for the maximum elastoplastic story drift of steel frames is related to the mean value of the maximum elastoplastic story drift. When the mean drift is small (less than 0.3%), an extreme value type I distribution is the best choice. However, for large drifts (more than 0.35%), an extreme value type II distribution is best.

• Journal of Korea Foundry Society
• /
• v.15 no.5
• /
• pp.494-506
• /
• 1995

Test castings in plate, disc, and cubic shaped castings for 0.2wt.% carbon and stainless steel have been poured to examine the effects of the riser dimensions including riser neck on the casting soundness. Three empirical methods were chosen in risering of steel castings. A computer program of solidification analysis considering liquid and solidification contraction was developed to apply for riserdesign calculated by using their methods in plate, disc, and cubic shaped castings, and to calculate the position and dimension of shrinkage cavity in complex shaped casting. The potential of present method has been successfully demonstrated by comparing predicted cavity shapes with those obtained in a series of experimental castings. Three empirical methods can be used in a practical way to make a rapid estimation of tie minimum riser diameter, but they can not provide a criterion of casting soundness with shape and material on all occasions. The shape and position of shrinkage cavity can be successfully predicted both using the present method and using risering calculated by their methods regardless of the shape and cast material.

• Journal of the Korean Academic Society of Industrial Cluster
• /
• v.2 no.1
• /
• pp.1-13
• /
• 2008

Despite growing recognition of the significance of industrial clusters to regional economic success, there has been only limited attention paid to the effectiveness of cluster policies in old industrial regions. Many of these regions still retain functioning industrial clusters, or have clusters which are adopting new strategies as part of a process of regeneration. This paper argues that the effectiveness of cluster policies in old industrial regions depends upon the extent to which they recognise the evolutionary nature of industrial clusters. It reviews the literature on the transformation of old industrial regions in Europe, and examines how cluster policies have risen to prominence as a policy tool. These strands ate brought together in an exploration of cluster policies in old industrial regions. A brief case study is presented of the evolution of the steel industry supply chain in north east England. The conclusions focus upon the data requirements that form a starting point for informed policy intervention into presses of cluster evolution.

• Economic and Environmental Geology
• /
• v.33 no.5
• /
• pp.379-389
• /
• 2000

This study was focused on the investigation for the heavy metal contamination of soils derived from Yoecheon Industrial Complex in Chonnam Province. Total 201 soil samples including farmland, paddy, forest and playground soils were collected, extracted by 0.1N HCl and analyzed for Cd, Cu, Cr, Fe, Mn and Zn using AAS. Most pH values in soils were weak acidic ranges of 4-6, while some of them were over 8.0. Concentrations of Cd, Cu, Fe and Zn in the soils tend to be relatively high around the Au-Ag mine area, railroad stations and oil station, however, those of Cr, Mn and Pb show high at the northside of Pohang Steel Co (POSCO). Cadmium-Zn couples, and Cd-Zn and Zn-Cr couples have relatively good correlations in the farmland soils and paddy soils, respectively. Concentrations of Cd, Fe and Zn with depth tend to be higher in the top soils than in the bottom soils, but those of Cu and Pb do not show regular variations with depth.

• Journal of Environmental Health Sciences
• /
• v.37 no.3
• /
• pp.182-192
• /
• 2011

Objectives: This study aims to identify the influential factors on the pulmonary function of targeted general residents in the areas surrounding Gwangyang Steel Mill. Methods: An PFT (Pulmonary Function Test) was conducted from May 2007 to November 2007 on 974 target residents (438 male, 536 female), including an exposed group (674 people) who resided within a radius of 5 km from Gwangyang Steel Mill in Gwangyang-si, Jeollanam-do and a control group (300 people) who resided outside a radius of 15 km. A survey related to personal characteristics, life habits, respiratory diseases and allergic symptoms, medical histories and living environments of the residents was also conducted to identify influential factors on pulmonary function. Results: As %$FEV_1$ and %FVC of the exposed group are 99.17% and 96.98%, respectively, and those of the control group are 105.47% and 101.91%, respectively, with the PFT values of the exposed group being lower than those of the control group (p<0.001), it turns out that the pollution in the industrial complex is likely to trigger a reduction in the pulmonary function of local residents. The odds ratio analysis result for asthma diagnosis history indicates that the odds ratios tend to be higher among surveyed residents who are living near above-average traffic volumes and are using beds, where it is statistically meaningful that especially the odds ratios are higher if the residences are closer to roads (p<0.01, CI=1.12-4.52). The factors that affect the FEV1 are identified as smoking, passive smoking, asthma diagnosis history, nasal congestion symptoms and allergic eye disease ($R^2$=0.154, p<0.001). The factors that affect the FVC are identified as smoking, passive smoking, asthma diagnosis history and allergic coryza ($R^2$=0.158, p<0.001). In addition, the analysis result for the relevance of air pollution levels to pulmonary function ($FEV_1$, FVC) shows that FEV1 and FVC tend to decrease as the concentration of $O_3$ increases. Conclusions: We believe that this study may provide preliminary data for the development of preventive measures for health effects on the residents and environmental health control measures for environmental pollution in the industrial complex area.

• Journal of Environmental Science International
• /
• v.13 no.6
• /
• pp.561-570
• /
• 2004

This study was carried out to survey the pollution of nonylphenol (NP) in surface sediments around Gwangyang bay and Yeosu sound. NP was suspected chemicals as endocrine disruption. Gwangyang bay is located on the mid south coast of Korea. It is a semi-closed bay which Yeosu petrochemical industrial complex, POSCO (Pohang Steel Company) and Gwangyang container harbor are there. The surface sediments were collected at 15 stations with gravity corer at October, 1999, February, May and August, 2000. Also, the stream and intertidal sediment were collected at 5 sites at August, 2000. Concentrations of NP in surface sediments were in the range of 6.89 to 202.70 ng/g dry wt.. Seasonal range (mean value) of NP is 13.98 to 30.48 (23.46) ng/g dry wt. at October, 10.35 to 54.91 (28.10) ng/g dry wt. at February, 29.05 to 202.70 (82.32) ng/g dry wt. at May and 6.98 to 83.40 (25.37) ng/g dry wt. at August. NP was seasonally fluctuated, and the highest mean value and range was detected at May, 2000. NP was highly distributed in the inner part of Gwangyang bay than Yeosu sound. Concentrations of NP in stream and intertidal sediments showed the highest value in downstream near Yeosu petrochemical industrial complex and Yondung stream. It suggests that the source of NP is industrial wastewater and municipal sewage.

• Journal of the Korean association of regional geographers
• /
• v.4 no.1
• /
• pp.77-98
• /
• 1998

In general, spatial imbalance in regional growth is a major cause of social and political conflicts within a state. In Korea, this inequality has functioned as a threat to the state's integration. With the economic development policies by regional industrialization over the past three decades, most of the industrial activities have been concentrated in Seoul and Pusan metropolitan areas, which are surrounded by Kyonggi, Kyongnam provinces respectively. Compared to these areas, Chonnam and Chonbuk provinces have lagged behind in economic development. Therefore, in order to increase the regional economic development of the southwestern region in Korea, the central government has been enforcing several policies aimed at regional industrialization since the 1980s. The purpose of this study focuses on the regional economic impacts of a newly established industrial estate-Yulchon industrial complex- which would act as a regional growth center in the Kwangyang bay area. The Kwangyang bay area consists of several industrial estates such as Kwangyang Iron and Steel Co. and its related industrial complex, Chuam rural industrial estate, Yeochon industrial complex, and so on. In addition, the Kwangyang container port was constructed in 1997. The Kwangyang bay area has been changing to a new industrial district in the southwestern part of Korea as a result of industrialization policies which were activated by central government. The Yulchon industrial complex, which is expected to be completed in 2001, would draw many manufacturing plants. For example, Hyundai Motors Co. has a plan to locate a new automobile assembly plant within the estate. As the plan has high probability to be realized, it will be interesting to study the effects a new automobile assembly plant and its related production linkages have on the region. This study is to estimate the expected structural characteristics of automobile production activities in Yulchon. The following details will be discussed: the regional economic impacts of a new automobile industry in Yulchon industrial complex, the production linkage formation via hierarchical subcontracting systems, the alternative strategies to promote the growth of regional economies, and the scheme to improve the auto-parts and components industry in Kwangju and Chonnam provinces by establishing auto-mobile production function. Automoblie industry generally gives great influences on not only regional economies but the related industries, for example, the firms producing automotive components. If a new plant producing automobiles and its related firms producing components are to be established in Yulchon, they will affect on the regional development directions and change the regional characteristics of industrial structure. In order to increase the spread effects of the new industry in Yulchon industrial complex, almost all of the automobile production processes must be organized concurrently within a limited range of distance. There is an imperative that the co-operation system should be structured between the assembly firm and many firms producing its components. In addition to those, it would be required such as the effective division of labors between the firms, much more capabilities in the technical innovations, and the reconstruction of interrelationship between the labor unions and the firms' managers.

• Journal of Environmental Impact Assessment
• /
• v.24 no.6
• /
• pp.549-560
• /
• 2015

The priorities of siting restriction was derived from quantification of environmental hazard according to industrial classification based on 'Chemical Ranking and Scoring System(CRS)' which is handling the discharge characteristics of 31 industrial classifications regulated from locating at 'Industrial Complex in Rural Area(ICRA)'. CRS that is utilizing the data of 'Pollutant Release and Transfer Registers(PRTR)' is applied to determine human health risk and ecological risk which are calculated by discharged amount and materials $LC_{50}$ according to water, soil and air media based on industrial classification. From this process, exposure assessment and toxicity assessment for integrating the adverse environmental impact and the mitigation effect of environmental risk according to the development of environmental technologies into establishing the rational landuse management method for the 31 industrial classifications regulated from locating at ICRA was analyzed. From the assessment result of the siting restriction removal at ICRA for 31 industrial classifications, based on 2012 year reference 6 industries that includes Manufacture of Guilt Coloration Surface Processing Steel Materials, Manufacture of Biological Product, Manufacture of Smelting Refining and Alloys of Copper, Dyeing and Finishing of Fibers and Yarns, Manufacture of Other Basic Iron and Steel n.e.c., Rolling Drawing and Extruding of Non-ferrous Metals n.e.c. are calculated as having relatively lower environmental hazards, thus it is judged that the siting restriction mitigation at ICRA is possible for the 6 industrial classifications that are not discharging the specific hazardous water contaminants during manufacturing process.

• Steel and Composite Structures
• /
• v.14 no.4
• /
• pp.349-365
• /
• 2013

Structures consisting of concrete and steel parts, which are irregular in damping ratios are investigated. This investigation is a code-based seismic design of such structures. Several practical difficulties encountered, due to inherent differences in the nature of dynamic response of each part, and the different damping ratios of the two parts. These structures are irregular in damping ratios and have complex modes of vibration so that their analysis cannot be handled with the readily available commercial software. Therefore, this work aims to provide simple yet sufficiently accurate constant values of equivalent damping ratios applied to the whole structure for handling the damping irregularity of such structures. The results show that the equivalent damping ratio changes with the height of the building and the kind of the structural system, but it is constant for all accelerations values. Thus, available software SAP2000 applied for seismic analysis, design and the provisions of existing seismic codes. Finally, evaluation of different kinds of structural system used in this research to find the most energy dissipating one found by finding the best value of quality coefficient.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.11
• /
• pp.1165-1173
• /
• 2008

An water-reuse network design has drawn attention as a systematic method of reducing fresh water usage and increasing water-using efficiency. The final goal of an eco-industrial park(EIP) is accomplishing industrial sustainability and constructing water-reuse network can be a solution. When designing water-reuse network connecting various processes which consume water, the water pinch technology can be used frequently, since it simultaneously minimize freshwater usage and wastewater discharge. In this research water pinch technology is applied to develop an effective water-reuse network in an EIP. Three scenarios based on different reusing strategies were developed. The results show that the final water-reuse network can reduce the total fresh water usage more than 30%, while the water expenses decrease by 20%. It can be concluded that water pinch technology is an effective tool to optimize water-reuse network among different industrial facilities.