• 한국지반환경공학회 논문집
• /
• 제18권9호
• /
• pp.11-18
• /
• 2017

수치해석기법을 이용한 말뚝의 거동특성 예측방법은 정재하시험비가 고가이기 때문에 공사 전 말뚝의 거동을 예측할 수 있다는 장점으로 설계단계에서 널리 이용되고 있지만 그 신뢰성에 대한 연구는 부족한 실정이다. 본 연구에서는 실제 현장에서 말뚝의 거동과 수치해석으로 예측한 말뚝의 거동을 비교함으로써 수치해석 기법의 신뢰성을 검증하였다. 지반과 말뚝의 상호작용에 의한 말뚝의 거동을 정확하게 파악하기 위하여 정재하시험이 수행되는 지반에서 시추조사, 현장원위치시험 등을 통해 지반특성을 확인하였고, 실규모 정재하시험을 수행하여 말뚝의 거동특성을 분석하였다. 정재하시험이 수행된 방식과 동일하게 수치해석을 모사하여 재하시험과 동일한 하중단계에서 말뚝의 거동을 수치해석으로 모사하여 현장시험 결과와 비교함으로써 수치해석 기법의 신뢰성을 검증하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.277-284
• /
• 2000

Using the large diameter (D ＝ 2,500mm, L ＝ 40m) batter steel pipe piles, designed as compression piles but used as reaction piles during the static compression load test of socketed test piles (D ＝ 1,000mm, L ＝ 40m), static pile load tests for large diameter instrumented rock-socketed piles were performed. The reaction steel pipe piles were driven 20m into the marine deposit and weathered rock layer and then l0m socketed with reinforced concrete through the weathered rock layer and into hard rock layer. Steel pipe and concrete in the steel pile part, and concrete and rebars in the socketed parts were instrumented to measure strains in each part. The pullout amounts of reaction pile heads were also measured with LVDT. During the static pile load test, total compressional load of about 20MN was loaded on the head of test piles, but load above 20MN was not loaded due to lack of loading capacity of loading system. Over the course of the study, maximum pullout amount up to 7mm was measured in the heads of reaction piles when loaded op to 10MN and 1mm of pullout amount was measured. More than 85% of pullout load was transfered in the residual weathered rock layer and about 10% in the soft rock layer, which was somewhat different transfer mechanism in the static compressional load tests.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.66-73
• /
• 2004

Prototype crushed-stone compaction pile(${\Phi}=700mm$) were constructed on specific test site. Static loading tests for crushed-stone compaction piles were performed. Based on the static loading test results, finite element analysis was performed using software PENTAGON 3D. Numerical analysis were done for the area replacement ratio($a_s$) of $20{\sim}70%$ and $a_s$ was varied as a step of 10%. In the single crushed-stone compaction pile, settlement was decreased as $a_s$ was increased. In the group pile, this tendency was similar. In the in-sit test and numerical analysis, as $a_s$ increased, the stress concentration ratio was increased. But $a_s$ in the numerical analysis were more than that of in-situ test, greatly.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.36-43
• /
• 2004

Most of pile foundations are fixed head condition, but lateral loading test for pile is performed under free head condition generally In this study, a lateral loading test for a large diameter drilled shaft was performed under the fixed pile head and the free pile head condition, where lateral displacement along the pile depth was measure. Test results and theoretical values were compared and analyzed.

• 한국지반공학회논문집
• /
• 제22권11호
• /
• pp.113-122
• /
• 2006

국내에서 말뚝 정재하 실험이 수많이 수행되고 있지만, 그 결과의 활용도가 낮아서 재하실험 방법과 분석방법 등에 대하여 재고할 필요성이 제기되고 있다. 본 연구에서는 두터운 연약지반 하부의 모래층에 PHC 말뚝 선단을 지지시킨 후 하중전이 정재하 실험을 수행하였다. 말뚝의 설치 이후에 장기간에 걸쳐 주면 마찰력을 측정하였으며, 국내에서 보편적으로 적용되고 있는 재하법과는 다른 급속재하법에 의하여 정재하실험을 실시하였다 그 실험결과를 이용하여 말뚝의 탄성계수, 잔류응력 및 참 지지력을 산정하였다. 결과적으로, 재하실험 전에 말뚝에 존재하는 잔류하중이 주면 마찰력과 선단지지력에 크게 영향을 미친다는 사실을 확인할 수 있었다. 또한, 점성토 지반에서의 장대말뚝에 대해서는 지반의 강도회복(setup) 효과가 매우 크다는 사실을 알 수 있었다.

• 토지주택연구
• /
• 제7권4호
• /
• pp.281-289
• /
• 2016

압축 부재인 PHC 말뚝(직경 600mm)도 강선의 부착력을 높이면 83.6~91.6tonf의 극한 인장력에 대해 구조적으로 저항할 수 있는 것으로 실험결과 나타났다. 이러한 시험결과에 안전율을 고려하여 적절한 허용값을 제시하면 부상방지 앵커를 대체하거나 절감시킬 수 있는 것으로 기대되었다. 이를 위해서는 구조적 인장성능과 함께 실제 지반에 시공된 매입말뚝의 인발저항 거동이 규명되어야 한다. 본 연구에서는 현장에 시공된 실제 매입말뚝의 인발거동 특성을 파악하기 위하여 정적 인발재하시험을 실시하여 주면마찰력 산정식과 비교하였다. 또한, 간편하게 인발저항력을 평가하기 위하여 PDA를 이용한 동재하시험을 실시하여 정적 인발재하시험 결과와 비교하였다. 그 결과, 매입말뚝의 시멘트풀이 충분히 경화한 후인 15일 후에는 LH 주면마찰력 산정식의 마찰력과 정적인발재하시험결과가 잘 일치하였고 동재하시험에서 구한 마찰력과도 비교적 잘 일치하는 것으로 나타났다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.8-10
• /
• 2013

Inorganic binding material was made by recycled resource and its applicability as pile-filling material was examined. The result was that the material had same liquidity with the liquidity of OPC and high reactivity with site soil. According to dynamic/static loading tests by site test-construction, the inorganic binding material met both design bearing capacity and settlement. Since the inorganic binding material showed same or better performance than OPC, the utilization possibility of the inorganic binding material made of recycled resource as pile-filling material was verified.

• Geomechanics and Engineering
• /
• 제12권4호
• /
• pp.611-626
• /
• 2017

The research reported herein is concerned with the model testing of piles socketed in soft rock which was simulated by cement, plaster, sand, water and concrete hardening accelerator. Model tests on a single pile socketed in simulated soft rock under axial cyclic loading were conducted and the bearing capacity and accumulated deformation characteristics under different static, and cyclic loads were studied by using a device which combined oneself-designed test apparatus with a dynamic triaxial system. The accumulated deformation of the pile head, and the axial force, were measured by LVDT and strain gauges, respectively. Test results show that the static load ratio (SLR), cyclic load ratio (CLR), and the number of cycles affect the accumulated deformation, cyclic secant modulus of pile head, and ultimate bearing capacity. The accumulated deformation increases with increasing numbers of cycles, however, its rate of growth decreases and is asymptotic to zero. The cyclic secant modulus of pile head increases and then decreases with the growth in the number of cycles, and finally remains stable after 50 cycles. The ultimate bearing capacity of the pile is increased by about 30% because of the cyclic loading thereon, and the axial force is changed due to the applied cyclic shear stress. According to the test results, the development of accumulated settlement is analysed. Finally, an empirical formula for accumulated settlement, considering the effects of the number of cycles, the static load ratio, the cyclic load ratio and the uniaxial compressive strength, is proposed which can be used for feasibility studies or preliminary design of pile foundations on soft rock subjected to cyclic loading.

• Advances in concrete construction
• /
• 제10권1호
• /
• pp.49-59
• /
• 2020

Precast concrete elements in accelerated bridge construction (ABC) extends from superstructure to substructure, precast pile foundation has proven a benefit for regions with fragile ecological environment and adverse geological condition. There is still a lack of knowledge of the seismic behavior and performance of the precast pile foundation. In this study, a 1/8 scaled model of precast pile foundation with elevated cap is fabricated for quasi-static test. The failure mechanism and responses of the precast pile-soil interaction system are analyzed. It is shown that damage occurs primarily in precast pile-soil interaction system and the bridge pier keeps elastic state because of its relatively large cross-section designed for railways. The vulnerable part of the precast pile with elevated cap is located at the embedded section, but no plastic hinge forms along the pile depth under cyclic loading. Hysteretic curves show no significant strength degradation but obvious stiffness degradation throughout the loading process. The energy dissipation capacity of the precast pile-soil interaction system is discussed by using index of the equivalent viscous damping ratio. It can be found that the energy dissipation capacity decreases with the increase of loading displacement due to the unyielding pile reinforcements and potential pile uplift. It is expected to promote the use of precast pile foundation in accelerated bridge construction (ABC) of railways designed in seismic regions.

• 한국지반공학회논문집
• /
• 제34권5호
• /
• pp.5-17
• /
• 2018

본 연구에서는 풍화암에 근입된 강관 매입말뚝의 안전율 제안을 위하여 정재하시험과 동재하시험을 수행하였다. 현장재하시험은 직경이 0.508, 0.457m 인 시험말뚝을 제작하여 정재하시험(14회)과 동재하시험(EOID 14회, Restrike 14회)을 실시하였다. 이때, 재하시험은 시험말뚝 시공완료 후 (1)초기동재하시험(EOID)을 수행하였으며, (2)시공완료 28일 후 정재하시험을 시행하였으며, (3)정재하시험 완료 후 15일 후에 재항타동재하시험(Restrike)을 실시하였다. 본 연구 결과 Davisson 판정법의 동재하시험을 이용한 지지력 산정 결과 정재하시험 대비 재항타동재하시험은 약 15% 낮게 나타났다. 정재하시험과 동재하시험의 지지력 분석을 통하여 안전율을 비교하였고, 최종적으로 동재하시험 안전율을 기존 2.0에서 1.75로 수정 제안하였다.