• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.280-285
• /
• 2000

A viscoelastic constitutive equation of rubber that is under small oscillatory load superimposed on large static deformation is proposed. The proposed model is derived through linearization of Simo's viscoelastic constitutive model and reference configuration transformation. The proposed constitutive equation is extended to a generalized viscoelastic constitutive equation that includes widely used Mormin's model as a special case using objective stress increment. Static deformation correction factor is introduced to consider the influence of Pre-strain on the relaxation function. The proposed constitutive model is tested fer dynamic behavior of rubber specimens with different carbon black contents. It is concluded from the test that the viscoelastic constitutive equation for filled rubber must include the influence of the static deformation on the time effects. The suggested constitutive equation with static deformation correction factor shows good agreement with test values.

• 한국지반공학회논문집
• /
• 제22권11호
• /
• pp.113-122
• /
• 2006

국내에서 말뚝 정재하 실험이 수많이 수행되고 있지만, 그 결과의 활용도가 낮아서 재하실험 방법과 분석방법 등에 대하여 재고할 필요성이 제기되고 있다. 본 연구에서는 두터운 연약지반 하부의 모래층에 PHC 말뚝 선단을 지지시킨 후 하중전이 정재하 실험을 수행하였다. 말뚝의 설치 이후에 장기간에 걸쳐 주면 마찰력을 측정하였으며, 국내에서 보편적으로 적용되고 있는 재하법과는 다른 급속재하법에 의하여 정재하실험을 실시하였다 그 실험결과를 이용하여 말뚝의 탄성계수, 잔류응력 및 참 지지력을 산정하였다. 결과적으로, 재하실험 전에 말뚝에 존재하는 잔류하중이 주면 마찰력과 선단지지력에 크게 영향을 미친다는 사실을 확인할 수 있었다. 또한, 점성토 지반에서의 장대말뚝에 대해서는 지반의 강도회복(setup) 효과가 매우 크다는 사실을 알 수 있었다.

• 한국지반공학회논문집
• /
• 제21권1호
• /
• pp.93-103
• /
• 2005

대구경 현장타설말뚝에 대하여 하중전이 측정을 수반한 정재하시험, 동재하시험 및 유한차분해석을 수행하여 주면 마찰력 거동특성에 대한 연구를 실시한다. 주면 마찰력은 말뚝과 지반의 상대변위와 직접적으로 관계되므로 임의의 심도에서 측정한 말뚝의 하중전이량과 유한차분해석에 의한 주면지반의 변위와 응력을 이용하여 거동특성을 분석한다. 하중전이측정결과에 의하면 현장타설말뚝 주면을 따라 발휘되는 극한단위주면 마찰력은 중간 깊이인 모래자갈층과 자갈층 상부에서 먼저 나타난다. 또한 동일한 현장타설말뚝에 대하여 동재하시험과 정재하시험을 실시한 결과 주면 마찰력과 선단지지력의 거동특성이 상이하게 평가되었으며, 그 차이점에 대하여 논의한다.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1999년도 Proceedings of the 1999 Annual Conference The Korean Society of Agricutural Engineers
• /
• pp.277-282
• /
• 1999

Recently , the use of steel fibers has been increased in flexural members and beams of concrete structures ; such as bridge decks, highway roads, runway of airport , buildings , ete.. An experimental investigation of the shear behavior of high-strength reinforced concrete beams using input steel fiber was conducted. However only a few experimental tests have been carried out under static loading . The static test was carried out to measure the ultimate load, the initial load of flexural and diagonal cracking , crack patters, fracture modes. The load versus strain and load versus deflection relation were obtained from the static test.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1384-1387
• /
• 2003

Pressurization test is usually required in aircraft full-scale static test. There are several test conditions including pressurization of cockpit, fuselage fuel tank, air inlet duct for T-50 full-scale static test. In this paper, the test conditions, equipment, piping analysis for the pressurization test are introduced. Tank simulation test is performed to verify the validity of piping analysis and to find good tuning parameters for the pressurization channel in the servo controller. Several test setup for pressurization of T-50 test is introduced. Test article volume is filled by form, $60%{\sim}80%$ volume is reduced for the T-50 full-scale static test. Pressurization system is connected to servo controller which also controls hydraulic actuator. Load and pressure control is synchronized by using the same servo controller during T-50 test. Typical control result for pressurization test condition is shown. Pressurization tests of T-50 full-scale static test was completed successfully.

• 한국구조물진단유지관리공학회 논문집
• /
• 제9권1호
• /
• pp.119-126
• /
• 2005

본 연구는 H형 및 Channel형 복공판의 정적 하중에 대한 성능을 규명하는데 그 목적이 있다. 보다 향상된 복공판의 성능이 요구되어짐에 따라 보강의 가능성 및 효율성을 파악하였고, 정적재하시험 및 구조해석을 통해 시험체의 개선효과를 비교 검토하였다. 정적재하시험을 통하여 응력과 처짐을 측정하였고, 이를 FEM 해석결과와 비교하였을 때 극한 하중 및 변위, 지간 중앙부와 상 하 플랜지의 휨응력 등에서 H형 복공판은 Channel형 복공판에 비해 약 3배 이상의 높은 강성을 보유하고 있는 것으로 나타났다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.290-292
• /
• 2004

In this paper, static and fatigue load tests for the specimens, components and carbody were carried out to investigate the strength of welded joints in aluminum rolling stock. Tensile load test results showed that the static strength of welded joint for heat-treated alloys is reduced significantly and fatigue strengths are scattered by the welding imperfections. Component and whole carbody fatigue test results showed agreements with the design fatigue strength standards for specimens of same joint detail. Test results revealed that full penetration welding and strict management of welding procedure are crucial for securing strength of welded joint in aluminum carbody.

• Wind and Structures
• /
• 제8권6호
• /
• pp.443-454
• /
• 2005

Wind loading is very important, even dominant in some cases, to large-span single-layer reticulated shells. At present, usually equivalent static methods based on quasi-steady assumption, as the same as the wind-resistant design of low-rise buildings, are used in the structural design. However, it is not easy to estimate a suitable equivalent static wind load so that the effects of fluctuating component of wind on the structural behaviors, especially on structural stability, can be well considered. In this paper, the effects of fluctuating component of wind load on the stability of a single-layer reticulated spherical shell model are investigated based on wind pressure distribution measured simultaneously in the wind tunnel. Several methods used to estimate the equivalent static wind load distribution for equivalent static wind-resistant design are reviewed. A new simple method from the stability point of view is presented to estimate the most unfavorable wind load distribution considering the effects of fluctuating component on the stability of shells. Finally, with comparisive analyses using different methods, the efficiency of the presented method for wind-resistant analysis of single-layer reticulated shells is established.

• 대한토목학회논문집
• /
• 제31권5C호
• /
• pp.163-170
• /
• 2011

본 연구에서는 국내 7개 현장에서 수행한 대구경 현장타설말뚝의 정재하시험 결과값을 이용하여 하중전이 함수식을 제안하였다. 하중전이실험이 수행된 대구경 현장타설말뚝의 정재하시험 결과로 부터 얻어진 축하중 분포도를 이용하여 단위주면 마찰력을 분석하였으며, 단위주면마찰력 자료에 기초하여 지반종류별 하중전이 함수식을 제안할 수 있었다. 단위주면하중전이 함수식에 의해 계산된 축하중분포도와 양방향 말뚝재하시험 시 측정된 축하중분포도를 비교하였다. 그 결과 제안된 하중전이함수에 의해 예측된 축하중분포도는 실험에서 구한 축하중분포도와 비교적 잘 부합되는 것으로 나타났다.

• Advances in aircraft and spacecraft science
• /
• 제2권3호
• /
• pp.345-365
• /
• 2015

This paper focuses on the design, fabrication, testing and analysis of a novel load-bearing element with energy dissipation capability. A single element comprises two von-Mises trusses (VMTs), which are sandwiched between two plates and connected to dashpots that stroke as the VMTs cycle between stable equilibrium states. The elements can be assembled in-plane to form a large plate-like structure or stacked with different properties in each layer for improved load-adaptability. Also introduced in the elements are pre-loaded springs (PLSs) that provide high initial stiffness and allow the element to carry a static load even when the VMTs cannot under harmonic disturbance input. Simulations of the system behavior using the Simscape environment show good overall correlation with test data. Good energy dissipation capability is observed over a frequency range from 0.1 Hz to 2 Hz. The test and simulation results show that a two layer prototype, having one soft VMT layer and one stiff VMT layer, can provide good energy dissipation over a decade of variation in harmonic load amplitude, while retaining the ability to carry static load due to the PLSs. The paper discusses how system design parameter changes affect the static load capability and the hysteresis behavior.