• Journal of Biomedical Engineering Research
• /
• v.24 no.2
• /
• pp.121-126
• /
• 2003

The purpose of this work was to assess and quantify whether the beneficial effects in long-term gas exchange at exciting frequency were obtained at different frequencies as well and then to develop a vibrating intravascular lung assist device(VIVLAD), for Patients suffering from acute respiratory distress syndrome(ARDS) or chronic respiratory problems. We investigate the optimal condition of the frequency band excited with new vibrator at state of limit hemolysis when blood hemolysis came to through a membrane vibration action. The experimental design and procedures were given for a device used to assess the effectiveness of membrane vibrations. Quantitative experimental measurements were performed to evaluate the performance of the device . and to identify membrane vibration dependence on blood hemolysis. We developed an analytical solution for the hydrodynamics of flow through a bundle of sinusoidally vibrated hollow fibers that is used to provide some insight into how wall vibrations might enhance the performance of the VIVLAD. In the result, it was measured that the effect of various excited frequencies in gas transfer rate and hemolysis from the maximum gas transfer rate at no vibration when the maximum gas transfer rates showed at module type 6, module type 6 consisted of 675 hollow fiber membranes The maximum oxygen transfer rate was caused by the occurrence of maximum amplitude and transfer of vibration to hollow fiber membranes when it was excited by the frequency band of 7Hz at each blood flow rate. because this frequency became the End mode resonance frequency of the flexible in blood flow. Also, when module type 6 was excited at an excited frequency of 7Hz. blood hemolysis was low. Therefore, we decided that the limit of hemolysis frequency is 7Hz . because maximum amplitude occurred at this frequency.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.2
• /
• pp.82-89
• /
• 2007

Glass-ceramics were fabricated by heat-treating a glass at $700^{\circ}C$/10hr which was obtained by melting a glass frit mixed with $40{\sim}80 wt%$ EAF dust at $1300^{\circ}C$/1hr. Dependence of crystal phase and bonding state change upon a compositional change and heat treatment condition were studied and the results was connected to the toxic characterization leaching procedure (TCLP) test data to investigate a chemical durability of the specimens. Increasing dust in a glass shifted the peak around $1000cm^{-1}$ to the lower frequency which was composed of two vibration peaks for the nonbridging oxygen at $960cm^{-1}$ and the bridging oxygen at $1050{\sim}1060cm^{-1}$. Also, the $B_2O_3$ structure of boroxol ring changed to a tetrhedral-, trigonal- and di-borate with dust addition. The Fe-O peaks in the glass-ceramics were observed which is consitent with XRD results of spinel formation. The surface of glass after TCLP test was severely cracked while there was no cracks on a glass-ceramics after TCLP test so the chemical durability of the glass-ceramics is superior than that of glass. The leaching concentration of Fe for the glass-ceramics containing EAF dust 80 wt% is 1/15 times lower than that of glass. The Zn leaching concentration fur the glass-ceramics containing dust < 70 wt% was higher than that of glass but its trend was reversed for the specimen of dust content > 80 wt% which could be concluded as correlated with occurrence of willemite phase.

• The Korean Journal of Physiology
• /
• v.29 no.2
• /
• pp.269-277
• /
• 1995

Membrane vesicles were prepared by differential centrifugation from epithelial cells of porcine trachea. Total activity of microsomal ATPases was measured spectrophotometrically by a coupled enzyme assay. The steady-state activity of the enzyme was $329{\pm}10$ nmol/min mg protein. Thapsigargin, a specific antagonist of intracellular $Ca^{2+}-ATPase$, inhibited about 50% of the activity, leaving $178{\pm}18\;nmol/min .mg$ protein (n=6), indicating that the $Ca^{2+}-ATPase$ is one of the major microsomal ATPases. The microsomes used in this study appeared to be tight-sealed vesicles since they showed saturation in $^{45}Ca^{2+}$ uptake experiments. Inositol 1,4,5-trisphosphate $InsP_{3}, 4\;{\mu}M$, an agonist of $InsP_{3}$-sensitive $Ca^{2+}$ release channel ($InsP_{3}$, receptor), and Ca-ionophore A23187 $(10\;{\mu}M)$ induced $^{45}Ca^{2+}$ releases of 20% and 50% of stored $^{45}Ca^{2+}$, respectively. The addition of $(10\;{\mu}M\;InsP_{3}$ also increased the microsomal ATPase activity from $282{\pm}8$ nmol/min mg protein to $334{\pm}21$ nmol/min . mg protein in the intact vesicles. Similar increase in the activity was observed by making microsomes leaky (uncoupling) using the Ca-ionophore A23187. ;$InsP_{3}-induced$ effects were blocked by either thapsigargin or heparin suggesting that: 1) the $InsP_{3}-induced$ increase in ATPase activity is mediated by microsomal $Ca^{2+}-ATPase$, and 2) dissipation of $Ca^{2+}$ gradient across the microsomal membrane is responsible for the $InsP_{3}-induced$ effect. In order to test the dependence of the $Ca^{2+}-ATPase$ activity on the activity of $InsP_{3}-induced$ the activity of ATPases was monitored in various concentrations of free $Ca^{2+}$ using $EGTA-Ca^{2+}$ buffers. The $Ca^{2+}$-dependent biphasic change is the well-known character of $InsP_{3} receptor but not of microsomal $Ca^{2+}-ATPase$ in non-excitable cells; however, the activity of microsomal ATPase appeared biphasic and a maxim진 activity of $397{\pm}36nmol/min\;.mg$ protein was obtained in the solution containing 100 nM free $Ca^{2+}$. Below or above this concentration, the activity of ATPases was lower. These results strongly support a positive correlation of microsomal $Ca^{2+}-ATPase$ to the $InsP_{3}$ receptors in epithelial microsomes.

• The Journal of the Korea Contents Association
• /
• v.16 no.9
• /
• pp.170-184
• /
• 2016

The research is our public rental housing policy are 'Why' Did you no choice but to make the route changes, according to previous governments neo-institutional one fine history of care institutions, Historical analysis method and historical comparison system was complementary to the borders of the principle of hacke to appear (248 hacker, 2004 :) that the path to the model attempts to analyze a mix of evolution. Our country has a high degree of exodus due to industrialization and urbanization have caused and here, by means of side effects to housing was becoming serious social problems. Has this to solve housing problems governments have any policy to take a look at the latest. 5, 16 5,16 Military Coup caused by the advent of the Third Republic ; lack of legitimacy of the regime established, the Korea Housing Corporation randomness that for over the cracks and a consensus on the critical period of Public Rental Housing begins to engage in further studies in this study reported paths of Lee Myung-bak administration during the course of evolution 'of nest housing', and government 'happy homes', Park Geun-hye, a diagnose and address the state of the public rental housing policy by comparison, the next of Public Rental Housing A desirable destination of the study to present.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.671-678
• /
• 2001

All solid-state thin film micro supercapacitor, which consists of $RuO_2$/LiPON/$RuO_2$ multi layer structure, was fabricated on Pt/Ti/Si substrate using a $RuO_2$ electrode. Bottom $RuO_2$ electrode was grown by dc reactive sputtering system with increasing $O_2/[Ar+O_2]$ ratio at room temperature, and a LiPON electrolyte film was subsequently deposited on the bottom $RuO_2$ electrode at pure nitrogen ambient by rf reactive sputtering system. Room temperature charge-discharge measurements based on a symmetric $RuO_2$/LiPON/$RuO_2$ structure clearly demonstrates the cyclibility dependence on the microstructure of the $RuO_2$ electrode. Using both glancing angle x-ray diffraction (GXRD) and transmission electron microscopy (TEM) analysis, it was found that the microstructure of the $RuO_2$ electrode was dependent on the oxygen flow ratio. In addition, x- ray photoelectron spectroscopy(XPS) examination shows that the Ru-O binding energy is affected by increasing oxygen flow ratio. Furthermore, TEM and AES depth profile analysis after cycling demonstrates that the interface layer formed by interfacial reaction between LiPON and $RuO_2$ act as a main factor in the degradation of the cyclibility of the thin film micro-supercapacitor.

• Journal of the Korean Magnetics Society
• /
• v.14 no.1
• /
• pp.33-37
• /
• 2004

Cu$_{0.1}$Fe$_{0.9}$Cr$_2$S$_4$ has been studied with Mossbauer spectroscopy, x-ray diffraction, vibrating sample magnetometer (VSM), and magnetoresistance (MR) measurement. The crystal structure was determined to be a cubic spinel with lattice parameter a$_{0}$=9.9880 $\AA$. The MR measurements show a semiconductor behavior below 110 K and metal behaved above 100 K. The temperature dependence of magnetization of Cu$_{0.1}$Fe$_{0.9}$Cr$_2$S$_4$ was reported. In addition to a large irreversibility between the zero-field-cooling (ZFC) and the field-cooling (FC) magnetization at applied field H=100 Oe, a cusp-like anomaly was observed in both the FC and ZFC curves. It shifted toward the lower temperature region with increasing magnetic field, and then showed convex type maximum at 110 K, under the applied field of 5 kOe. The Mossbauer spectra were measured from 15 K to room temperature. The asymmetric line broadening was observed for the sample Cu$_{0.1}$Fe$_{0.9}$Cr$_2$S$_4$, and it was considered to be dynamic Jahn-Teller relaxation. The charge state of Fe ions was ferrous in character. The unusual reduction of magnetic hyperfine field below 110 K was interpreted in terms of cancellation effect between the mutually opposite orbital current field (H$_{L}$) and Fermi contact field (H$_{C}$).

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.102-108
• /
• 2013

In manufacturing of solution-processed organic electronic devices, a spin coating method is frequently used, but which has a big problem. Solvent in a solution has a decisive effect such as physical and chemical damage for successive solution-based film deposition. Such a severe damage by solvent restricts for fabricating building blocks of multi-layered films from solutions. In this work, it will be shown that a proper combination of well-known solvents gives a chance to fabricate multi-layered film, also this new method was applied to make organic field effect transistor. Two types of bottom gate, bottom contact transistors were fabricated, one of which is fabricated by conventional single spin coating method, the other fabricated by double spin coating method. Compared with the electrical characteristics in a single spin coated transistor, the leakage current between source and gate electrode was decreased, ON state current was increased, and the extracted saturation mobility was multiplied more than 2.7 time for double spin coated transistors. It is suggested that the multiple coated gate dielectric structure is more desirable for high performance organic ferroelectric field effect transistors.

• Journal of The Korean Association For Science Education
• /
• v.25 no.3
• /
• pp.400-410
• /
• 2005

According to the cognitive conflict process model, student anxiety factor is known to have both positive and negative effects on student response behaviors in a conflict situation for conceptual change learning. However, there is little research that reveals what type of anxiety, either constructive or destructive, is related when conducting step-by-step experiments to resolve cognitive conflicts. This study attempted to learn the characteristic of explanatory hypothesis according to anxiety type after conducting five step-by-step experiments related to action and reaction concept. Results found that students who belonged to the types of 'conviction in logical misconception', 'insisting on additional variables', and 'reasonable modification' suggested explanatory hypothesis close to physical nature. On the other hand, those who showed the other five types of anxiety ('compatible predictions', 'dependence on others', 'fusion of past experience', 'lack of confidence', and 'conflict with past experience') suggested temporary supported hypothesis or simple explanatory hypothesis according to student intuition and simple observation. These results indicate that students in the above-mentioned five categories need more external interactions with instructors based on the type of anxiety related to student behavior. In addition, the results present student characteristics which instructors should be more attentive to when using step-by-step experiments to resolve cognitive conflicts.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.145-145
• /
• 2008

High-k materials have been paid much more attention for their characteristics with high permittivity to reduce the leakage current through the scaled gate oxide. Among the high-k materials, $ZrO_2$ is one of the most attractive ones combing such favorable properties as a high dielectric constant (k= 20 ~ 25), wide band gap (5 ~ 7 eV) as well as a close thermal expansion coefficient with Si that results in good thermal stability of the $ZrO_2$/Si structure. During the etching process, plasma etching has been widely used to define fine-line patterns, selectively remove materials over topography, planarize surfaces, and trip photoresist. About the high-k materials etching, the relation between the etch characteristics of high-k dielectric materials and plasma properties is required to be studied more to match standard processing procedure with low damaged removal process. Among several etching techniques, we chose the inductively coupled plasma (ICP) for high-density plasma, easy control of ion energy and flux, low ownership and simple structure. And the $BCl_3$ was included in the gas due to the effective extraction of oxygen in the form of $BCl_xO_y$ compounds. During the etching process, the wafer surface temperature is an important parameter, until now, there is less study on temperature parameter. In this study, the etch mechanism of $ZrO_2$ thin film was investigated in function of $Cl_2$ addition to $BCl_3$/Ar gas mixture ratio, RF power and DC-bias power based on substrate temperature increased from $10^{\circ}C$ to $80^{\circ}C$. The variations of relative volume densities for the particles were measured with optical emission spectroscopy (OES). The surface imagination was measured by scanning emission spectroscope (SEM). The chemical state of film was investigated using energy dispersive X-ray (EDX).

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.2
• /
• pp.21-32
• /
• 1996

The performance of the energy density control algorithm for controlling a broadband noise is evaluated in a one-dimensional enclosure. To avoid noncausality problem of a control filter, which often happens in a frequency domain optimization, analyses presented in this paper are undertaken in the time domain. This approach provides the form of the causally constrained optimal controller. Numerical results are presented to predict the performance of the active noise control system, and indicate that imp개ved global attenuation of the broadband noise can be achieved by minimizing the energy density, rather than the squared pressure. It is shown that minimizing the energy density at a single location yields global attenuation results that are comparable to minimizing the potential energy. Furthermore, unlike the squared pressure control, the energy density control does not demonstrate any dependence on the error sensor location for this one-dimensional field. A practical implementation of the energy-based control algorithm is presented. Results show that the energy density control can be implemented using the two sensor technique with a tolerable margin of performance degradation.