• Journal of the Korean Ceramic Society
• /
• v.13 no.2
• /
• pp.8-16
• /
• 1976

The conductive transparent film is prepared by spraying thin salt solution. In stannic chloride solution as a base solution, various dopants such as Al, Co, Cu and Ni were dissolved respectively as a chloride state and then the films were made by spraying solutions on hot glass plates. The properties of them were compared with those of the stannic salt single component film. The films doped with copper oxide and nickle oxide were improved by decreasing their sheet resistivity and temperature coefficient of resistivity. In comparison with the sheet resistivity and temperature coefficient of resistivity of stannic oxide single component film, being 2.5 K ohm/$\textrm{cm}^2$ and -1650ppm/$^{\circ}C$ respectively, its values of the film containing 15 mol % of copper oxide and formed at 40$0^{\circ}C$ were 2.5K ohm/$\textrm{cm}^2$ and -920ppm/$^{\circ}C$ respectively. The film containing 15 mol % of nickel oxide and formed at 50$0^{\circ}C$ has shown its sheet resistivity and temperature coefficient 0.7 K ohm/$\textrm{cm}^2$ and -940ppm/$^{\circ}C$ respectively.

• Journal of the Korean Ceramic Society
• /
• v.12 no.2
• /
• pp.10-14
• /
• 1975

Bodies whose compositions are in the ternary system BaCO3-TiO2-SnO2 containing from 5 to 90 mol % stannic oxide were prepared to improve the thermal characteristics of barium titanate dielectrics. Bodies having dielectric constant (K) of 2100 at 1 KHz, low negative temperature coefficients of 1500ppm up to about 9$0^{\circ}C$, Curie Temperature of 2$0^{\circ}C$, and dissipation factor of 0.2-0.4% were obtained with addition of 15 mole % stannic oxide.

• 전기의세계
• /
• v.20 no.4
• /
• pp.23-30
• /
• 1971

The photovoltaic behaviors ahve been observed with a sandwich-type cell, consisting of a junction between .betha.-carotene and stannic oxide conducting layer to provide a junction electrode. In the stannic oxide and .betha.-carotene junction it was found that its electromotive forse decreased to a value smaller than the original one. This is due to a space charge formation. Photovoltage reached approximately 40mV with an irradiation energy of 250Kcal/M$^{2}$hr. It appeared that a magnitude of the photovoltaic response was proportional to the logarithm of irradiance. The time constant of the photovoltaic effect was shown to be approximately 0.7 sec. The wavelength dependence of the photovoltaic behavior was very anomalous. It is assumed that such an anomalous photoresponse depends on a internal capacitance due to some bubble during process to make a cell.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.1
• /
• pp.34-41
• /
• 2003

Effects of additives and plating conditions of high speed electroplating were investigated. The Sn content in electrodeposit was highly decreased with increasing current density from $10A/dm^2$ to $50A/dm^2$, and the current efficiency on the cathode was decreased. The carbon content in the electrodeposit was decreased with increasing current density from $10A/dm^2$ to $30A/dm^2$, however the carbon content was highly increased in the range of $40A/dm^2$$∼50A/dm^2$. The formation of tetravalent tin and stannic oxide sludge was prevented by the addition of gallic acid in the bath. The changing of Sn content in the electrodeposit is caused by the addition of gallic acid.

• Journal of the Korean Ceramic Society
• /
• v.12 no.1
• /
• pp.5-11
• /
• 1975

Thick film resistor paste was made utilizing oxide materials such as SnO, SnO＋Sb2O3, and SnO＋Zn. The oxide materials were mixed respectively with Q-12 glass powder and finally suspended in ethyl cellulose dissolved in ethyl cellosolve. Thick film resistor was made by screen printing the paste on the alumina substrate and firing it at a suitable temperature. Among thick films made from the resistor paste, the thick film containing 85% SnO and fired at $600^{\circ}C$ demonstrated the finest electrical properties showing 10 K ohm in sheet resistance, 110 ppm/$^{\circ}C$ in TCR. In general, TCR of the thick films made from the oxide-mixture paste is good in linearity, therefore it is suggested the oxide-mixture paste is utilized as the negative thermistor.

• Korean Journal of Materials Research
• /
• v.3 no.4
• /
• pp.319-326
• /
• 1993

The effects of $SnO_2$ crystallite size on the powder characteristics, the resistance in air and the sensitivity to 0.5 vol % $H_2$, CO-air mixture were observed. The size of SnO, powder was controlled by calcining temperature variation ($500^{\circ}C$ ~$1100^{\circ}C$) of $\alpha$-stannic acid fabricated from $SnCl_4 \cdot xH_2O$. Its crystallite size. evaluated from TEM image, was in the range of 8-54nm. With the reduction of crystallite size, the adsoption peak of $H_2O$ on FTIR curve became more clear while the lattice parameters were invariable. As the crystallite size decreased, with elements of thick film, the temperatures showing a minimum resistance in air and a maximum sensitivity to H, gas reduced. The temperature variations were assigned to the changes of activation energy of the active adsorbates, and it was suggested that the decrease of activation energy can be one of the reasons for the' sensitivity increase with the' fine powder.

• Journal of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.102-109
• /
• 1987

Some characteristics of $SnO_2$ film which was deposited on a slide glass substrate, using dibutyl tin diacetate and oxygen, by the chemical vapor deposition were observed. The optimum condition for the preparation of the film was found to be at 420$^{\circ}C$ of substrate temperature for 20 min of deposition. Important optical, electrical, and structural features of the film were examined. It was found that the typical $SnO_2$ film on the untreated substrate was 4000${\AA}$ in thickness, transmitted 90% of the visible liglit, and provided 5800 ohms/${\square}$ of the sheet resistance. It was also found that the surface treatments of the slide glass by acid leaching were beneficial. The film structure was found to be a mixture of polycrystalline tetragonal stannic oxide confirmed by the X-ray diffraction and to be spherical fine grains concluded by the scanning electron microscopy.

• Korean Journal of Materials Research
• /
• v.25 no.1
• /
• pp.27-31
• /
• 2015

This paper proposes a novel way of fabricating aligned porous Sn by freeze-drying of camphene slurry with stannic oxide ($SnO_2$) coated Sn powders. The $SnO_2$ coated Sn powders were prepared by surface oxidation of the initial and ball-milled Sn powders, as well as heat treatment of tin chloride coated Cu powders. Camphene slurries with 10 vol% solid powders were prepared by mixing at $50^{\circ}C$ with a small amount of oligomeric polyester dispersant. Freezing the slurry was done in a Teflon cylinder attached to a copper bottom plate cooled at $-25^{\circ}C$. Improved dispersion stability of camphene slurry and the homogeneous frozen body was achieved using the oxidized Sn powder at $670^{\circ}C$ in air after ball milling. The porous Sn specimen, prepared by freeze-drying of the camphene slurry with oxidized Sn powder from the heat-treated Sn/tin chloride mixture and sintering at $1100^{\circ}C$ for 1 h in a hydrogen atmosphere, showed large pores of about $200{\mu}m$, which were aligned parallel to the camphene growth direction, and small pores in their internal walls. However, $100{\mu}m$ spherical particles were observed in the bottom part of the specimen due to the melting of the Sn powder during sintering of the green compact.