• Computers and Concrete
• /
• v.2 no.5
• /
• pp.367-380
• /
• 2005

Recent earthquakes have shown that many of existing buildings in Iran sustain heavy damage due to defective seismic details. To assess vulnerability of one common type of buildings, which consists of low rise framed concrete structures, three defective and three standard columns have been tested under reversed cyclic load. The substandard specimens suffered in average 37% loss of strength and 45% loss of energy dissipation capacity relative to standard specimens, and this was mainly due to less lateral and longitudinal reinforcement and insufficient sectional dimensions. A relationship has been developed to introduce variation of plastic length under increasing displacement amplitude. At ultimate state, the length of plastic hinge is almost equal to full depth of section. Using calibrated hysteresis models, the response of different specimens under two earthquakes has been analyzed. The analysis indicated that the ratio between displacement demand and capacity of standard specimens is about unity and that of deficient ones is about 1.7.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.184-193
• /
• 2015

This paper proposes a cost-efficient and automatic method for large data acquisition from a test chip without expensive equipment to characterize random process variation in an integrated circuit. Our method requires only a test chip, a personal computer, a cheap digital-to-analog converter, a controller and multimeters, and thus large volume measurement can be performed on an office desk at low cost. To demonstrate the proposed method, we designed a test chip with a current model logic driver and an array of 128 current mirrors that mimic the random process variation of the driver's tail current mirror. Using our method, we characterized the random process variation of the driver's voltage due to the random process variation on the driver's tail current mirror from large volume measurement data. The statistical characteristics of the driver's output voltage calculated from the measured data are compared with Monte Carlo simulation. The difference between the measured and the simulated averages and standard deviations are less than 20% showing that we can easily characterize the random process variation at low cost by using our cost-efficient automatic large data acquisition method.

• Journal of Korean Society for Quality Management
• /
• v.43 no.4
• /
• pp.589-606
• /
• 2015

Purpose: In developing new products, reducing performance variation is important for competitiveness factors such as quality, cost, and delivery. This paper aims at evaluating three performance variations; measurement, performance evaluation, and manufacturing variations, and then improving product and process design, focused on paper helicopter making case study. Methods: For measurement system analysis, gage R&R (repeatability and reproducibility), linearity, stability are evaluated. Since gage R&R are not satisfactory, the measurement system is improved by adopting voice memos application of iPhone and providing standard measurement procedure. To evaluate performance variation, product deterioration and environment factor (wind speed) is considered. Since the existing design is sensitive to these noise factors, a new product design is developed, which is proven to be robust to the noise factors. Finally, manufacturing variations are evaluated with five factors which can cause variation in flight time. To reduce the impact of three significant factors, three improvement methods are applied. Results: Three performance variations are evaluated and robust paper helicopter design is presented. Conclusion: To reduce measurement and process variations, improved measurement method and paper helicopter making procedure are proposed. A new product design is also presented which is robust to deterioration and environmental variation. This paper is expected to benefit students and practitioners who want to have hands-on knowledge on new product quality improvement.

• Journal of Sensor Science and Technology
• /
• v.13 no.6
• /
• pp.462-472
• /
• 2004

In this study, we measured the blood flow on arm by non-invasive method and implemented a system to measure variation of the blood flow by estimating bio-electrical impedance and arterial pressure according to cuff pressure. The implemented system measured impedance variation according to pressure variation applied by artificial cuff pressure on the measuring position. The system consisted of pressure measuring part and impedance measuring part using 4-electrode method. Pressure measuring part was composed of semiconductor pressure sensor and electronic circuit for signal processing of sensor output signal. In addition, impedance measuring part was composed of constant current source circuit and lock-in amplifier for detecting impedance signal. We conducted experiments of impedance measuring part using standard resistance for performance evaluation of the implemented system. In addition we experimented to estimate variation of the blood flow by measuring impedances of the experimental group. We estimated ratio of the blood flow resistance using mean arterial pressure and variation of the blood flow. As a result the ratio of the blood flow resistance and variation of blood flow were in an inverse relationship with each other and the correlation coefficient was -0.96776.

• Journal of Astronomy and Space Sciences
• /
• v.30 no.3
• /
• pp.175-178
• /
• 2013

Recently, two instruments of cosmic ray are operating in South Korea. One is Seoul muon detector after October 1999 and the other is Daejeon neutron monitor (Kang et al. 2012) after October 2011. The former consists of four small plastic scintillators and the latter is the standard 18 NM 64 type. In this report, we introduce the characteristics of both instruments. We also analyze the flux variations of cosmic ray such as diurnal variation and Forbush decrease. As the result, the muon flux shows the typical seasonal and diurnal variations. The neutron flux also shows the diurnal variation. The phase which shows the maximum flux in the diurnal variation is around 13-14 local time. We found a Forbush decrease on 7 March 2012 by both instruments. It is also identified by Nagoya multi-direction muon telescope and Oulu neutron monitor. The observation of cosmic ray at Jangbogo station as well as in Korean peninsula can support the important information on space weather in local area. It can also enhance the status of Korea in the international community of cosmic ray experiments.

• New & Renewable Energy
• /
• v.7 no.4
• /
• pp.30-36
• /
• 2011

The objective of this study is to investigate the effects of the refrigerant charge amount on the performance of a water-to-water ground source heat pump with a variation of compressor speed and the secondary fluid flow rate. The water-to-water ground source heat pump was tested by varying refrigerant charge amount from -40% to 20% of full charge. Compressor speed was changed from 30 Hz to 75 Hz and the secondary fluid flow rate was adjusted from 6 LPM to 14 LPM. For all test conditions, EWTs of an indoor heat exchanger and an outdoor heat exchanger were maintained at standard conditions of ISO 13256-2. The slope of the COP with the variation of charge amount is much steeper at undercharged conditions than that at overcharged conditions. For all compressor speed, the variation of the system performance according to charge amounts showed the similar trends. However, the optimum charge amount of the system increased a little with an increment of compressor speed. When the secondary fluid flow rate decreased, the system was optimized at higher refrigerant charge amount conditions.

• Natural Product Sciences
• /
• v.21 no.1
• /
• pp.14-19
• /
• 2015

Several $19{\alpha}$-hydroxyursane-type triterpenoids and hydrolysable tannins have beneficial effects on human health. Rubus crataegifolius (Rosaceae) has the cleft simple leaf whereas R. parvifolius has pinnate compound leaves. This research was aimed to find the variation in the contents of the triterpenoids and tannins between the infected versus uninfected leaves of R. coreanus and R. parvifolius and between young versus mature leaves. Triterpenoids and tannins were quantitatively analyzed by HPLC. Six triterpenoids including tormentic acid, euscaphic acid, 23-hydroxytormentic acid, coreanoside $F_1$, kaji-ichigoside $F_1$ and niga-ichigoside $F_1$ were used for standard compounds. Gallotannins and ellagitannins were quantitatively evaluated using the indicatives of methyl gallate and ellagic acid. The infected leaves of R. crataegifolius contained higher levels of triterpenoids and tannin than the uninfected leaves; however, lower quantity of total tannin was observed in the mature leaves than in the young leaves. Although the pinnate compound leaves of R. parvifolius exhibited similar tendency of those compositional variation with R. crataegifolius each other, its contents of triterpenoids do not considerably vary. Variation of the contents of triterpenoids and tannins were particularly distinct in R. crataegifolius by growth and infection.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.23-26
• /
• 1997

In exposuring x-rays, we can adjust three variables of kVp, mA and sec. The kVp is one of main factors affecting x-ray quality -peneterability. And miliampere-seconds is directly proportional to x-ray quantity. In this paper, we detected voltage variation of CdS, II-VI group semiconductor compounds, by kVp as the fundamental experiments of designing x-ray dosimeter. We exposured x-ray on the material from 40 to 100 kVp by increasing 2kVp using Shimadazu TH-500-125 Radio-Tex cx-s x-ray machine. We fixed miliampere -seconds to 100mA and 0.2 sec. After acquiring the raw data, we plotted the graph of kVp and voltage variation and figured slope value of 0.093 by regression. The standard deviation of voltage to kVp was 0.22. For the future study, the mAs variation study will be needed to investigate the connections between kVp and mAs in order to design x-ray dosimeter.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1656-1662
• /
• 2010

Automatic train control systems are divided into ATC, ATP and ATS systems etc. The ATP and ATS systems offer discontinuous information for train control. While the ATC systems provide continueous information for train control. There is a method for offering continuous information by AF track circuits. Magnetic fields are formed by current through rails in the AF track circuit systems. So, the continuous information is received by the magnetic fields on a on-board antenna. Coating materials on rails are researched to decrease defects such as head check, shelling, corrugation, squats and so on in Germany. Currently, a coating method of rail construction is proposed by using the ceramics in Korea. When deciding physical characteristic of ceramics, researches are required about variation of flux density by the ceramics. In case that the flux density is much lower than existing value, the information for train control is not transmitted to the on-board antenna. In this paper, inductance on rails is calculated and a model is presented about variation of the magnetic field intensity in the AF track circuit. Standard permeability of ceramics is proposed by analyzing the variation of magnetic field intensity. It is demonstrated by using Maxwell and Matlab program.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.10 no.3
• /
• pp.17-25
• /
• 1986

The objectives of this study are to investigate the variation of the sleeve form by changing arm movements and to study the relationship among the three aspects of sleeve (sleeve height, width and armhole girth) by changing arm movements. Plasrun gyps were used for this experimental research. The subjects of this study were elementary schoolgirls (9$\~$12 years old). Arm mevements were 4 types($0^{\circ},\;45^{\circ},\;90^{\circ},\;135^{\circ}$) to the vertical directions. The statistical methods used to analyze the data included mean, standard deviation, the Pearson's correlation coefficients and coefficients of determination. The results obtained from this study were as follows; 1. According to the arm movements, the sleeve form changed more in the front than in the back. 2. As the arm movements were increased vertically, the heights of sleeves and the girths of the armholes were decreased, and the widths of sleeves were increased. 3. Variation rates by changing arm movements were different according to the variation of arm movement, and were the highest in sleeve height. 4. There was a negative correlation between sleeve height and width, and a positive correlation between sleeve height and armhole girth.