• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1993.04a
• /
• pp.135-140
• /
• 1993

The optimum weight design of structure is to determine the combination of structural members which minimize the weight of structures and satisfy design conditions as well. Since most of loads and design variables considered in structural design have uncertain natures, the reliability-based optimization techniques need to be developed. The aim of this study is to estabilish the general algorithm for the minimum weight design of transmission tower structure system with reliability constraints. The sequential linear programming method is used to solve non-linear minimization problems, which converts original non-linear programming problems to sequential linear programming problems. The optimal solutions are produced for various reliability levels such as reliability levels inherent in current standard transmission tower cross-section and optimal transmission tower cross-section obtained with constraints of current design criteria as well as selected target reliability index. The optimal transmission towers satisfying reliability constraints sustain consistent reliability levels on all members. Consequently, more balanced optimum designs are accomplished with less structural weight than traditional designs dealing with deterministic design criteria.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.5
• /
• pp.529-538
• /
• 2006

Separating a reentry vehicle into warhead and body is a conventional and efficient means of producing a huge decoy and increasing the kinetic energy of the warhead. This procedure causes the radar to track the body, whose radar cross section is larger, and ignore the warhead, which is the most important part of the reentry vehicle. However, the procedure is difficult to perform using standard tracking criteria. This study presents a novel tracking algorithm by integrating input estimation and modified probabilistic data association filter to solve this difficulty in a clear environment. The proposed algorithm with a new defined association probability in this filter provides a good tracking capability for the warhead ignoring the radar cross section. The simulation results indicate that the errors between the estimated and the warhead trajectories are reduced to a small interval in a short time. Therefore, the radar can produce a beam to illuminate to the right area and keep tracking the warhead all the way. In conclusion, this algorithm is worthy of further study and application.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.63-66
• /
• 2005

Six RC pier were tested under a constant axial load and a cyclically reversed horizontal load to investigate the performance of RC piers used in the high strength concrete and the high strength rebar. It is designed with a hollow section according to the Korean Bridge Design Standard. The variables of the test were concrete strength, rebar strength, a ratio of lap splice and a ratio of transvere rebar. The test results show that the performance of a RC Pier; failure mode, crack pattern, maximum load and ductility.

• Korean Journal of Veterinary Research
• /
• v.56 no.1
• /
• pp.53-55
• /
• 2016

A 1-year-old Korean domestic short-haired cat presented with skin hyperextensibility and a severely macerated wound on the skin of the dorsal part of the neck. Diagnostic studies including histopathology and skin extensibility index revealed congenital cutaneous asthenia (Ehlers-Danlos syndrome). In this cat, the skin wounds and defects were successfully managed with standard wound management and cosmetic surgery. Although skin hyperextensibility is persistent, the cat has lived well without other complications to date. To the best of our knowledge, this is the first report of cutaneous asthenia in a cat in Korea.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.17 no.3
• /
• pp.100-106
• /
• 2009

As an effort to prevent environmental problems caused by ozone depletion and global warming, alternative refrigerants are being developed, and one of the candidates is carbon dioxide. To overcome slightly low efficiency of $CO_2$ refrigeration system, air-conditioning cycle using an ejector was suggested. Ejector compensates throttling loss in an expansion device by reducing compression work. In this study, the ejector refrigeration cycle using $CO_2$ as a refrigerant is investigated to understand the effect of the mixing section diameter and refrigerant charge amount on the performance. If mixing section diameter is too large or too small, either cases show low performance. The optimum refrigerant charge amount which gives the best performance is found for standard operating conditions. The air-conditioning cycle was analyzed for several operating conditions.

• Steel and Composite Structures
• /
• v.47 no.1
• /
• pp.135-145
• /
• 2023

This study presents a numerical investigation into the hysteretic behavior of cold-formed austenitic stainless steel square hollow section (SHS) brace members using a commercial finite element (FE) analysis software ABAQUS/Standard. The initial/post buckling and fracture life of SHS brace members are comprehensively investigated through parametric studies with FE models incorporating ductile fracture model, which is validated against the existing laboratory test results collected from the literature. It is found that the current predictive models are applicable for the initial buckling strengths of SHS brace members under cyclic loading, while result in significant inaccuracy in predictions for the post-buckling strength and fracture life. The modified predictive model is therefore proposed and the applicability was then confirmed through excellent comparisons with test results for cold-formed austenitic stainless SHS brace members.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.3
• /
• pp.788-792
• /
• 2013

A shortcoming of using transmission electron microscopy (TEM) for structural analysis via electron diffraction is the relatively large error of the measurements as compared to X-ray diffraction. To reduce these errors, various internal standard methods from earlier studies have been widely used. We developed a new device to facilitate the application of internal standard methods in preparation of TEM grids used for nanopowder analysis. Through the application of a partial mask on the TEM grid, both the internal standards and the research materials can be loaded on the same grid. Through this process, we conducted a TEM analysis that compared synthetic hydroxyapatite (HAp) nanopowder to bone apatite from a bovine femur. We determined that the accuracy of the d-spacing measurements of the HAp and bone powders could be improved to better than 1% after statistical treatments of the experimental data. By applying a quarter mask, we loaded four different nanoparticles on a single TEM grid, with one section designated for the internal standard.

• International Journal of Quality Innovation
• /
• v.6 no.3
• /
• pp.132-152
• /
• 2005

Today's society requires companies to act more and more effectively for the general good, by respecting human rights and the environment. Innovative and enlightened companies try to meet this need through the adoption of several initiatives. Accordingly, the International Standard Organisation is now working on attempts to unify these initiatives and to formulate an internationally recognised standard, providing guidance to companies on social responsibility. Currently the SA8000 international standard is the most often used tool-based on Corporate Social Responsibility (CSR) philosophy - which guarantees the respect of fundamental workers' rights. Since 2003, Italy holds the world record for its number of SA8000 certified companies. This paper discusses the findings of a two-stage survey of the Italian SA8000 certified companies carried out over the last two years. The focus of the survey is on both reasons and effects of the implementation of SA8000 standard. In the first stage the rate of response was very high while in the second stage it was satisfactory. The results provide a clear picture of the companies and their degree of achievement and awareness of the fundamental principles of human resource management. A section of the survey deals with some issues related to the Public Sector.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.563-568
• /
• 2008

The Green Building Certification is issued through self-assessment of applicant, assessment of assessment members and deliberation committee members. These assessments are carried out based on a standard provided Ministry of land transport and maritime affairs and environment. However, opinion difference of assessment standards could be occurred due to diversity of understanding for a standard or subjectivity of committee member. In this paper, We discussed the primary cause of score difference after analyzed assessment standard for the site, transportation, energy and resources, ecological environment, indoor environment in five different Apartment Houses located in Seoul. At a result, score difference was at least 3 points in each section except indoor environment and total score difference of housing complex is by 10 points. To improve these problems, educational program should be activated and guide for assessment standard should be published.

• Journal of Korean Association for Spatial Structures
• /
• v.22 no.4
• /
• pp.59-70
• /
• 2022

In SRC column, the closed hoops are applied with the same detail of both 135° standard hooks to expect the same performance as hoops of RC columns. This standard detail is actually complicated to construct, thus, two separating rebars are connected in the form of a square shape and welded over the overlapping section. But this is also complicated in construction practice. Therefore, this study describes experimental results regarding cyclic behaviors shown with alternative hoops cramped by the steel clip type-binding device instead of welding and standard specimen. As a result of the experiment, the specimens with alternative hoops of the SRC column showed comparable performance to the specimens with closed hoops. Therefore, it can be evaluated that the alternative hoops applied with the rebar confinement clips in the SRC column can replace the closed hoop.