• International Journal of Precision Engineering and Manufacturing
• /
• 제5권3호
• /
• pp.19-25
• /
• 2004

Pitch measurements of 150 nm one-dimensional grating standards were carried out using a contact mode atomic force microscopy with a high resolution three-axis laser interferometer. This measurement technique was named as the 'nano-metrological AFM'. In the nano-metrological AFM, three laser interferometers were aligned precisely to the end of an AFM tip. Laser sources of the three-axis laser interferometer in the nano-metrological AFM were calibrated with an I$_2$ stabilized He-Ne laser at a wavelength of 633 nm. Therefore, the Abbe error was minimized and the result of the pitch measurement using the nano-metrological AFM could be used to directly measure the length standard. The uncertainty in the pitch measurement was estimated in accordance with the Guide to the Expression of Uncertainty in Measurement (GUM). The primary source of uncertainty in the pitch-measurements was derived from the repeatability of the pitch-measurements, and its value was about 0.186 nm. The average pitch value was 146.65 nm and the combined standard uncertainty was less than 0.262 nm. It is suggested that the metrological AFM is a useful tool for the nano-metrological standard calibration.

• Journal of Environmental Health Sciences
• /
• 제20권1호
• /
• pp.28-38
• /
• 1994

The objective of this study were to measure concentrations of indoor pollutants in public transportation systems to provide importance of indoor air quality in transportation systems to policy makers. Indoor air quality of the pollutants (CO, CO$_2$, PM-10) and environmental sources (temperature, humidity) were measured at subway, seat-type bus, and city-type bus in the Seoul area from April to September 1992. The same pollutants and environmental sources were also measured at selected bus stops and subway stations during October 1991-September 1992. The mean concentrations of indoor pollutants in the public transportation systems were showed 115.5 $\mu$g/m$^3$ in PM-10, 6.8 ppm in CO, and 2167.9 ppm in CO$_2$, respectively. The mean values of PM-10 and CO showed below the U.S. 24 hour standard value of PM-10 and the Korea ambient CO standard, while the mean concentrations of CO$_2$ exceeded the Korea CO$_2$ standard. The highest levels of indoor concentration at public transportation systems were PM-10 of 134.6 $\mu$g/m$^3$ in the subway, CO of 8.9 ppm in the city-type bus, CO$_2$ of 2,511.1ppm in seat-type bus, respectively. The results showed that indoor air quality in bus and subway seemed likely to be affected by number of passengers and outdoor air infiltrated from exhausted gases of automobiles.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• 제10권5호
• /
• pp.43-51
• /
• 1996

An appropriate lighting standard for the museum is needed to minimize the deterioration of the exhibits by the light. To obtain the basic data for the standard, a system to measure the color change of the artifacts as a function of the radiation energy frequency was constructed. Xenon lamp is used as a light source, and the light is irradiated to the samples through serveral cut-off filters. Measuring the colors of the samples under each filters, color change of the samples is estimated for each frequency ranges of radiation energy. As a result, natural dyes show severe color change in a short time, but traditional papers shows relatively small color change. Using measured results, color change due to other light sources can be calculated and this will be the base of the standard.

• Journal of Korean Society of Disaster and Security
• /
• 제5권2호
• /
• pp.21-26
• /
• 2012

Disaster management standard has not been invigorated because it usually has documented qualities. Since its enactment and notification, there has been a lack of continual education and publicity that lead to poor awareness on disaster management. The purpose of this study investigates on activating the use of disaster management standards by disaster related agencies and organization during their work. It proposes details on how to distribute and promote disaster management standards, develop textbook, evaluation and feedback. Furthermore, it also developed an organizational structure and legal framework as measure for disaster management.

• Journal of Integrative Natural Science
• /
• 제1권2호
• /
• pp.79-83
• /
• 2008

As a new standard for performance measurement, NEMA NU2-2001 was presented recently. In this study, I investigated the spatial resolution, sensitivity, scatter fraction, and noise equivalent count ratio (NECR) in order to know the information of physical characteristics and system performance of GE discovery ST using this new standard. Bismuth germinate crystals ($6{\times}6$ array, $6.3mm{\times}6.3mm{\times}30mm$) were used in discovery ST (energy window:375-650 keV, coincidence window:11.7 nsec). To measure the sensitivity, five aluminum sleeves (Data Spectrum Corp., Chapel Hill, NC., USA, thickness:1.25 mm)-NEMA sensitivity phantom- filled with F-18 solution were used. Successive measurements in 2D and 3D acquisition mode were made with a line source at the center of transaxial field of view and 10 cm off from the center until the count was over 500,000. Spatial resolution was estimated using a point source (F-18, 0.1 mCi) at different locations in the FOV. Scatter fraction and NECR was tested using a NEMA scatter phantom. Dynamic data were acquired for 7 half-lives using F-18 solution. And true to background ratio was averaged at last three frames when the random rate was as small as ignorable for the calculation of scatter fraction. We anticipate this overall evaluated results could be used for the quality assurance and optimized image acquisition for clinical research.

• Journal of the Korea Safety Management & Science
• /
• 제7권4호
• /
• pp.141-163
• /
• 2005

The international SPICE (Software Process Improvement and Capability determination) Project ISO/IEC 15504(SPICE : Software Process Improvement and Capability determination) is an emerging International Standard on SPA(Software Process Assessment). A prime motivation for developing this standard has been the perceived need for an internationally recognized software process assessment framework that pulls together the existing public and proprietary models and methods. A SPICE assessment can be considered as one of representative SPA model since assessors assign ratings to indicators and metrics to measure the capability of software process. But this models doesn't provide a systematic measurement procedures and dynamic method for SPI(Software Process Improvement). Through the evaluation of SPICE is capable of providing a substantiated basis for using the notion of capability, as well as providing information for nacessary improvements to the standard using 6sigma process. As a result, this paper propose a measurement procedure and guidelines for application of 6sigma process to guarantee the reliability in SPI and suggest the structure to support SPI on overall organization.

• Journal of the Korean Society of Safety
• /
• 제28권1호
• /
• pp.18-23
• /
• 2013

The purpose of this study were to develop and validate a prototype slipmeter used on-site floor. The developed slipmeter was dreg sled type. It measured static coefficient of friction(SCOF). The developed slipmeter was evaluated with ASTM 2508-11 which use four different standard surfaces(polished granite, glazed porcelain, vinyl composite tile, and ceramic tile). The SCOF was then measured with developed slipmeter under the three different contaminants and seven different floors. The test results of slipmeter were also compared with those of BOT-3000, floor surface roughness, and human perception. The test results revealed that developed slipmeter successfully ranked all four standard surfaces and differentiated among standard surfaces with varying degrees of slipperiness. The developed slipmeter couldn't properly measure slipperiness under the two kind of floors(polished tile, ground steel plate) and one kind of contaminant(glycerol). The test results of developed slipmeter had stronger correlation with those of BOT-3000 and floor roughness under the water and detergent solution than under the glycerol. The test results of developed slipmeter also showed stronger correlation with those of BOT-3000 and surface roughness than those of human perception. The newly developed slipmeter had been found to give consistent results under the test conditions except for two kind of floors(polished tile, ground steel plate) and one kind of contaminant(glycerol).

• Journal of the Korean Society of Industry Convergence
• /
• 제25권2_2호
• /
• pp.299-307
• /
• 2022

Wireless earphones, along with smart devices, are the most sought-after products by consumers. Compared to general earphones, wireless earphones do not have twisted wires and are easy to use, so various types of products are currently on the market. However, information on quality is somewhat lacking, so consumers tend to purchase products according to brand awareness, and manufacturers are delivering information to consumers using different standards for each product because there is no standard for quality control. In particular, the playback time of wireless earphones is a factor that directly affects consumers' purchases, so a standard measurement method is needed to properly measure it. In this paper, we present a method for measuring the audio playback time of wireless earphones derived from domestic wireless earphone status survey, commercial product measurement test, and research analysis, and a developed standard measurement method. In addition, this paper proposes a measurement result reporting format to provide accurate information to consumers and induce a fair competitive environment for each product to manufacturers.

• Journal of Korean Port Research
• /
• 제10권2호
• /
• pp.17-29
• /
• 1996

It is required to consider pricing and non-pricing factors and external economy in order to achieve the objects of physical distribution system in a port. Recently, among the three factors, much attention has been paid to non-pricing factor in the system. Although physical distribution service in a port(PDSP)has been frequently mentioned in documents and literature related to port and shipping studies, few study on it has not been systematically and scientifically made due to the following problems; $\circ$ there are not proper criteria to evaluate level and quality of PDSP and as a result it is difficult to set up a unified standard for doing so. $\circ$ algorithms to evaluate problems with complex and ambiguous attributes and multiple levels in PDSP are not available. This thesis aims to establish a paradigm to evaluate PDSP and to abvance existing decision making methods to deal with complex and ambiguous problems in PDSP. To tackle the first purpose, extensive and thorough literature survey was carried out on general physical distribution service, which is a corner stone to handle PDSp. In addition, through interviews and questionnaire to the expert, it have extracted 82 factors of physical distribution service in a port. They have been classified into 6 groups by KJ method and each group defined by the expert's advice as follows; a. Potentiality b. Exactness c. safety d. Speediness e. Convenience f. Linkage Prior to the service evaluation, many kinds of its attributes must be identified on the basis of rational decision owing to complexity and ambiguity inherent in PDSP. An analytical hierarchy process (AHP) is a method to evaluate them but it is not applicable to PDSP that have property of non-additivity and overlapped attributes. Therefore, probablility measure can not be used to evaluate PDSP but fuzzy measure is required. Hierarchical fuzzy integral method, which is merged AHP with fuzzy measure, is also not effective method to evaluate attributes because it has vary complicated way to calculate fuzzy measure identification coefficient of attributes. A new evaluation algorithm has been introduced to solve problems with multi-attribute and multi-level hierarchy, which is called hierarchy fuzzy process(HFP).Analysis on ambiguous aspects of PDSP under study which is not easy to be defined is prerequisite to evaluate it. HFP is different from algorithm existed in that it clarified the relationship between fuzzy measure and probability measure adopted in AHP and that it directly calculates the family of fuzzy measure from overlapping coefficient and probability measure to treat and evaluate ambiguous and complex aspects of PDSP. A new evaluation algorithm HFP was applied to evaluate level of physical distribution service in the biggest twenty container port in the world. The ranks of the ports are as follows; 1. Rotterdam Port, 2. Hamburg Port, 3. Singapore Port, 4. Seattle Port, 5. Yokohama Port, 6. Long beach Port, 7. Oakland Port, 8. Tokyo Port, 9. Hongkong Port, 10. Kobe Port, 11. Los Angeles Port, 12. New york Port, 13. Antwerp Port, 14. Felixstowe Port, 15. Bremerhaven Port, 16. Le'Havre Port, 17. Kaoshung Port, 18. Killung Port, 19. Bangkok Port, 20. Pusan Port

• Journal of the Korean Academy of Esthetic Dentistry
• /
• 제7권1호
• /
• pp.64-70
• /
• 1998

Recently as the interest on Esthetic Dental Prosthesis is arising, the domains of Esthetic Dentistry is being widely investigated. Esthetic Dental Prosthesis is influenced greatly by the shape, color, tooth arrangement of the teeth and the facial features(including the lips). So the degree to which these characters harmonize will be the professional esthetical standard while the satisfaction of the patient will be another esthetical measure. The reason for this is that each and every one of us has a different standard of what is considered beautiful. Of course it doesn't mean that every standard is correct. Then what does Esthetical Prosthesis mean and what should the standard be? This must be defined as a prosthesis that satisfies the basic requirements - margin, contour, occlusion, and at the same time it should restore the shape, color, and tooth arrangement which the client(patient) would love to have. As Esthetic Prosthesis contains its subjective meaning a great deal, it shouldn't be simply distinguished between the beauty of the teeth itself or ugliness. Also in some case, it needs surgical treatment to make it harmonious in the whole aspect so that one may keep the feeling of satisfaction and security. Then what is the shape, color, tooth arrangement that each individual wants? There is an indefinite variety. For example, considering arrangement both regular and irregular is considered beautiful by each different individual. Regular arrangement may be the standard of beauty for some, while irregular arrangement may be thought of as natural looking and beautiful. That is why there must be enough communication with the patient and an agreement be made at the clinic before a diagnostic plan and actual surgery. The treatment plan as mentioned above must be sent to the dental laboratory. In this research, by using case studies, I am going to the importance and appropriateness of the data and information for the dental technician's esthetic prosthesis.