• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.286-288
• /
• 2006

The metallurgical and mechanical properties of fiction stir welded 304 austenitic stainless steel and AISI 1018 steel for fundamental study. Single-pass bead on plate weldments in the two steels were successfully achieved. The joints were evaluated by microscopy and hardness tests of the transverse cross section and transverse tensile tests.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1997년도 한국재료학회 추계학술발표회
• /
• pp.40-40
• /
• 1997

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2017년도 추계학술발표회
• /
• pp.34-34
• /
• 2017

• 대한조선학회논문집
• /
• 제45권5호
• /
• pp.530-537
• /
• 2008

Austenitic stainless steels(SUS 304, SUS 316), which are used for safety control valve of LNG carrier, are occasionally exposed in the cryogenic environment. In this regards, it is required to evaluate the mechanical characteristics under the low temperature environment. In this study, a series of uniaxial tensile test was carried out varying temperature for austenitic stainless steel. The phenomena of the strain-induced plasticity have been observed on the all temperature ranges. The critical value for threshold of 2nd hardening due to the phase transformation induced plasticity as well as the increase of hardening have been reported. The summarized experimental results would be used for the validation of numerical techniques applicable for the nonlinear hardening behavior of austenitic stainless steel under the cryogenic temperature environment.

• 한국주조공학회지
• /
• 제26권1호
• /
• pp.17-26
• /
• 2006

The substitution of cooling method from water quenching to air cooling after solution heat treatment was aimed for the development of a convenient and economical heat treatment process of duplex stainless steels without deterioration of mechanical and corrosion resistant properties for the industry. In order to achieve this goal, the mechanical properties and corrosion properties of a ASTM A890-4A duplex stainless steel were systematically investigated as functions of casting condition and cooling method after solution heat treatment. A 3-stepped sand mold and a permanent Y-block mold were used to check the effects of solidification structure and cooling rate after solution heat treatment. The microstructural characteristics such as the ferrite/austenite phase ratio and the precipitation behavior of ${\sigma}$ phase and carbides were investigated by combined analysis of OM and SEM-EDX with an aid of TTT diagram. Hardness and tension test were performed to evaluate the mechanical properties. Impact property at $-40^{\circ}C$ and corrosion resistance were also examined to check the possibility of the industrial application of this basic study. Throughout this investigation, air-cooling method was proved to effectively substitute for water-quenching process after the solution heat treatment, when the duplex stainless steel was sand mold cast with a thickness below 15 mm or permanent mold cast with a thickness below 20 mm.

• Nuclear Engineering and Technology
• /
• 제56권6호
• /
• pp.2131-2140
• /
• 2024

The chloride-induced stress corrosion cracking (CISCC) is one of the major integrity concerns in dry storage canisters made of austenitic stainless steels (ASSs). In this study, an advanced duplex stainless steel (DSS) with a composition of Fe-19Cr-4Ni-2.5Mo-4.5Mn (ADCS) was developed and its performance was compared with that of commercial ASS and DSS alloys. The chemical composition of ADCS was determined to obtain greater pitting and CISCC resistance as well as a proper combination of strength and ductility. Then, the thermomechanical processing (TMP) condition was applied, which resulted in higher strength than ASSs (304L SS and 316L SS) and better ductility than DSSs (2101 LDSS and 2205 DSS). The potentiodynamic polarization and electrochemical impedance spectra (EIS) results represented the better pitting corrosion resistance of ADCS compared to 304L SS and 316L SS by forming a better passive layer. The CISCC tests using four-point loaded specimens showed that cracks were initiated at 24 h for 304L SS and 144 h for 316L SS, while crack was not found until 1008 h for ADCS. Overall, the developed alloy, ADCS, showed better combination of CISCC resistance and mechanical properties as dry storage canister materials than commercial alloys.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권3호
• /
• pp.238-244
• /
• 2017

플라즈마 이온질화 기술은 특히 스테인리스강의 표면경도 향상을 통한 기계적 성질 개선을 위해 산업 전반에서 널리 사용되고 있다. 또한 저온처리가 가능할 뿐만 아니라 담금질 강, 가스 질화 또는 침탄에 비해 변형이 적으며, 높은 표면 경도와 부식 저항성을 향상시키는 이점이 있다. 많은 연구자들에 의해 $450^{\circ}C$ 이하의 온도에서 플라즈마 이온질화 처리 시 expanded austenite(S-상)에 의해 부식 저항성이 향상되는 것으로 나타났다. 이때 대부분의 실험은 HCl 또는 NaCl과 같은 염화물 용액에서 실시되었다. 그러나 전기화학적인 요인으로서 염화물 용액과 천연해수 사이에는 차이가 있다. 따라서 본 연구에서는 304 스테인리스강에 대하여 다양한 온도에서 플라즈마 이온질화 처리 후 천연해수 용액에서 전기화학적 특성 분석을 통해 결과적으로 내식성이 가장 우수한 최적의 플라즈마 이온질화 처리 온도 조건을 규명하였다.

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.349-356
• /
• 2002

For two kinds of 25Cr-20Ni stainless steels, STS310J1TB and STS310S with and without a small amount of Nb and N, creep behavior has been studied in a stress and temperature range from 147 to 392 MPa and from 923 to 773 K with a special reference to tertiary creep. The average creep life of STS310J1TB was about 100 times longer than that of the STS310S. The apparent activation energy for the initial creep rate was 330 kJ/mol in STS310J1TB, while that of the STS310S was 274kJ/mol in a power law creep region and 478 kJ/mol in a region of power law breakdown (PLB). The activation energy for STS310S below PLB is close to the for self-diffusion. When compensating for the temperature dependence of the Young's modulus and the omega value, it was found that the apparent activation energy for STS310J1TB was reduced to the activation energy for diffusion of chromium atom in gamma steel. The stress exponent of STS310S was about 12.3 above PLB and 5.1 in a power law creep region. Notwithstanding that the creep condition for STS310J1TB was in a power law creep region, its stress exponent was 7.9 larger than that of STS310S corresponding to the same creep conditions. This was ascribed to the presence of fine precipitates in STS310J1TB.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권5호
• /
• pp.678-685
• /
• 2010

STS304와 22APU 스테인리스강에 가스 텅스텐 아크용접을 하였다. 이 경우 두 강의 용접부의 부식특성을 전기화학적 방법으로 검토하였다. STS304 용접금속의 경도(Hv-250)는 22APU 강(Hv-217) 보다 상대적으로 높은 값을 보였다. 22APU의 용접금속과 STS 304의 열영향부의 부식전류 밀도는 다른 용접부위와 비교하여 각각 높은 값이 관찰 되었으며, 이것은 예민화 온도 영역에 있는 STS 304의 열영향부와 22APU의 용접금속에 형성된 크롬탄화물로 크롬결핍이 더욱 활성태의 양극으로 쉽게 부식된 것에 기인하는 것으로 사료된다. 그리고 이들 두 강의 용접금속과 열영향부는 크롬결핍상태에 있는 입자 사이 경계의 선택부식으로 입계부식을 나타내었다. 결과적으로 다른 용접방법의 적용이나 적절한 용접봉 사용은 두 강의 용접부에 대한 내식성을 개선하기 위해서 필요한 것으로 사료된다.

• 비파괴검사학회지
• /
• 제34권3호
• /
• pp.241-247
• /
• 2014

본 연구는 고온강도와 화학적 안전성으로 산업기계 구조물의 주요 소재로 사용되고 있는 AISI316 오스테나이트기 스테인레스강의 장시간 등온열처리에 따른 초음파 비선형성 특성을 평가하였다. 장시간 등온열처리는 정해진 시간을 변수로 전기로에서 가속열처리를 수행하였다. 미세조직적으로 정밀분성을 통하여 장시간 열처리에 따른 초음파 비선형성의 변화와 미시적 손상거동을 면밀히 평가하였다. 초음파 비선형성은 1000시간까지 급격하게 감소하고 이후 서서히 감소하였다. 표면조직적으로 입계의 모양이 다각형에서 원형으로 변하며 특히, 1000시간에서는 쌍정이 모두 분해되었다. 입계에 존재하던 델타페라이트는 1000시간에서 관찰되지 않으며 ${\sigma}$상으로 지속적인 변태가 진행되었다. 결과적으로 열처리 초기에는 보이드나 전위의 소멸 그리고 쌍정의 소멸로 초음파 비선형성은 급격히 감소를 하고 이후에는 입계에 $Cr_{23}C_6$석출물의 생성과 ${\sigma}$상 생성으로 초음파 비선형성은 미소하지만 지속적으로 감소한 것으로 판단된다.