• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.5
• /
• pp.393-400
• /
• 2013

The air supply system has a significant effect on the efficiency of polymer electrolyte membrane fuel cell (PEMFC) systems. The performance and efficiency of automotive PEMFC systems are greatly influenced by their air supply system configurations. This study deals with the system simulation of automotive PEMFC systems using MATLAB/Simulink framework. In this study, a low-pressure operating PEMFC system adopting blower sub-module (turbo-blower) is modeled to investigate the effects of stack operating temperature and air stoichiometry on the parasitic power and efficiency of automotive PEMFC systems. In addition, the PEMFC net system efficiency and parasitic power of air supply system are mainly compared for the two types (low-pressure operating and high-pressure operating) of automotive PEMFC systems under the same net power conditions. It is suggested that the obtained results from this system approach can be applied for establishing the novel operating strategies for FC vehicles.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2067-2069
• /
• 1998

A prototype semiconductor switch for the command resonant charging system has been developed for a line type modulator, which charges parallel pulse forming network(PFN) up to voltage of 5 kV at repetition rates of 60 Hz. A phase controlled power supply provides charging of the 4.7 ${\mu}s$ filter capacitor bank to voltage up to 5 kV. A solid state module of series stack array of sixe matched SCRs(1.6 kV, 50 A) is used as a command charging switch to initiate the resonant charging cycle. Both resistive and RC snubber network are used across each stage of the switch assembly in order to ensure proper voltage division during both steady state and transient condition. A master trigger signal is generated to trigger circuits which are transmitted through pulse transformer to each of the 6 series switch stages. A pulse transformer is required for high voltage trigger or power isolation. This paper will discuss trigger method, protection scheme, circuit simulation, and test result.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.7
• /
• pp.1302-1308
• /
• 2010

In this study, Zigbee Sensor Node to transmit harmful gases CO and $CO_2$ information using wireless communication within the ground and underground structures were developed. Wireless communication protocol was used Zigbee Stack included IEEE 802. 15.4 MAC protocol. For wireless transmission of detected harmful gas signal from ADC of MCU was implemented Zigbee Sensor Node that was developed protocol using Serial-Port-Profile(SPP) here. The proposed Zigbee Sensor Node was verified transmission distance from experiments. Transmission distance was into 90m in experiments. Distance experiments were measured at 10m intervals using sine & pulse wave input signal at indoors. The proposed Route Sensor Node was applied mesh routing protocol. When built up USN(Ubiquitous Sensor Network)using Route Sensor Node, transmission distance was not limited. On the experimental results, harmful gas values between direct measurements and USN measurements were consistent. The semiconductor CO sensor and N-DIR $CO_2$ sensor module as a harmful sensor was used. Therefore, the proposed Zigbee Sensor Node was verified about reliability and validity to build USN for transmission of harmful gas information.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.2
• /
• pp.91-101
• /
• 2012

A 200 W portable polymer electrolyte membrane fuel cell (PEMFC) system is developed. The PEMFC system consists of an air-cooled fuel cell stack module, a fuel supply subsystem, a power management subsystem, and a control electronics subsystem. The control logic is designed for the stable system operation. The system-level performance evaluation discloses that the present PEMFC system provides a rated power output of 200.5 W at 13.4 V with the maximum balance-of-plant (BOP) efficiency of 72%, and maximum system efficiency based on lower heating value (LHV) is 37% at 120.7 W system power output.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.5
• /
• pp.484-492
• /
• 2012

The TMS(Thermal Management System) heater in a fuel cell vehicle has been developed to prevent a decline of fuel cell durability and cold start durability. Main functions of the COD(Cathode Oxygen Depletion) heater are depletion of oxygen in a cathode as heat energy and consumption of electric power for rapid warming up of a fuel cell stack. This paper covers subjects including the design specification of a heater, heater controller for detection of overheat and reliability assessment including coolant pressure cycle test of a heater. To verify the design concept, burst pressure and deformation analysis of plastic housing were carried out. Also, temperature distribution analysis of heater surface and coolant inside of housing were carried out to verify the design concept. By designing the plastic housing instead of a steel housing, the 30% weight lightening and 50% cost reduction were attained. A module-based design of a TMS system including a heater or reducing the watt density of a heater is a problem to be solved in the near future work.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.68-78
• /
• 2019

The emergence of high voltage conversion applications has resulted in a trend of using semiconductor device series associations. Series associations allow for operation at blocking voltages, which are higher than the nominal voltage for each of the semiconductor devices. The main challenge with these topologies is finding a way to guarantee the voltage balance between devices in both blocking and switching transients. Most of the methods that have been proposed to mitigate static and dynamic voltage unbalances result in increased losses within the device. This paper introduces a new series stack topology, where the voltage unbalances are reduced. This in turn, mitigates the switching losses. The proposed topology consists of a circuit that ensures the soft switching of each device, and one auxiliary circuit that allows for switching energy recovery. The principle for the topology operation is presented and experimental tests are performed for two modules. The topology performs excellently for switching transients on each of the devices. The voltage static unbalances were limited to 10%, while the activation/deactivation delay introduced by the lower module IGBT driver takes place in the dynamic unbalances. Thus, the switching losses are reduced by 40%, when compared to hard switching configurations.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.2382-2392
• /
• 2014

In this paper, a new data frame structure for wavelength routing in optical ring access network(ORAN) is designed and the functions of each field in the frame are defined. In addition, the IP packet transmission to the network layer corresponding to the newly proposed structure of the protocol stack is newly presented. Tha data transmission protocol design techniques of ORAN was proposed. IP packet and broadcasting packet transmission within the sub-network, and the IP packet transmission to other sub-network was shown through the process illustration. In the process, the encapsulation and framing process of the wavelength information to routing has been described in detail. And each step takes place in a packet transfer process is demonstrated. A ring type optical access network protocol is not yet research field. ORAN data transfer protocol to send/receive module structure of a subscriber node and a control node of the two rings which analyzed the results are shown. The high-speed Internet solution is proposed that by using wavelength routing the packet transport protocol for ORAN is designed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.842-848
• /
• 2011

A fabricated hybrid control board using multi-communication is designed with a low power 8-bit microcontroller, ATxmega128A1. The microcontroller consists of 8 UART (Universal asynchronous receiver/transmitter) ports, 2 kbytes EEPROM, 128 kbytes flash memory, 8 kbytes SRAM. The 8 URAT ports are used for a multi-communication modem, a GPS module, etc. The EEPROM is used for saving a configuration for running programs, and the flash memory of 128 kbytes is used for storing a F/W (Firm Ware), and the 8 kbytes SRAM is used for stack and for storing memory of global variables while running programs. If we use the multi-communication of CDMA, TRS and RF to remotely control Aid to Navigation, it is able to remove the communication shadow area. Even though there is a shadow area for an individual communication method, we can select an optimal communication method. The compatibility of data has been enhanced as using of same data frame per communication device. For the test, 8640 of data have been collected from each buoy during 30 days in every 5 minutes and the receiving rate of the data has shown more than 85 %.

• Membrane Journal
• /
• v.12 no.4
• /
• pp.226-239
• /
• 2002

A process simulation model of pervaporation process has been developed as a design tool to analyse and optimize the dehyhration of organic solvents through a commercial scale of pervaporative plate-and-frame modules that contain a stack of membrane sheets. In the simulation model, the mass balance, the heat balance and the concentration balance are integrated in a finite elements-in-succession method to simulate the overall process. In the integration method, a feed channel between membrane sheets in the modules was taken as differential unit element volume to simplify calculation procedure and shorten computing time. Some of permeation parameters used in the simulation model, were quantified directly from the dehydration experiment of ethanol through $AzeoSep^{TM}$-2002 membrane which is a commercial pervaporation membrane. The simulation model was verified by comparing the simulated values with experimental data. Using the model, continuous and batch pervaporation processes were simulated, respectively, to acquire basic data for analysing and optimizing in the dehydration of ethanol through the membrane. Based on the simulation results, a comparison between the continuous and the batch pervaporation processes would be discussed.

• Journal of Korea Multimedia Society
• /
• v.8 no.11
• /
• pp.1472-1482
• /
• 2005

In this paper, we propose a socket interface layer for large-scale multimedia servers that adopt TCP/IP Offload Engines (TOE). In order to provide legacy network applications with binary level compatibility, the socket interface layer intercepts all socket-related system calls to forward to either TOE or legacy TCP/IP Protocol stack. The layer is designed and implemented as a kernel module in Linux. The layer is located between BSD socket layer and INET socket layer, and passes the application's socket requests to INET socket layer or TOE. The layer provides multimedia servers and web servers with the following features: (1) All standard socket APIs and file I/O APIs that are supported (2) Support for binary level compatibility of existing socket programs (3) Support for TOE and legacy Ethernet NICs at the same time.