• Journal of Environmental Science International
• /
• v.4 no.5
• /
• pp.123-123
• /
• 1995

The treatment performances of anaerobic-aerobic activated sludge process were investigated under various operation conditions. The treatment system proposed in this study gave a relatively stable performance against hourly change of the flow rate and showed a satisfactory removal of nitrogen and phosphorus compounds under experimental conditions. The recycle ratio of mixed liquor from aerobic to anaerobic region and peak coefficient primarily controlled the extent of nitrogen removal. The recycle ratio had the optimum values which were determined by the microbial activities of nitrification and denitrification. The behavior of the treatment unit could be simulated by using the kinetic equations and reactor models which considered the treatment units as complete mixing tanks.

• Journal of the Korean Society of Safety
• /
• v.12 no.1
• /
• pp.9-18
• /
• 1997

This paper is a study on the dynamic characteristics of truncated cone type squeeze film damper(SFD) bearing and rotor system. This model can alter the radial oil film gap which Is Important to the performance of rotor-bearing system and manufactured easily to change the shape concept of traditional circular type SFD bearing. In theoretical analysis, the oil film pressure distribution, the oil film force, the film damping coefficient and the eccentricity ratio, etc. were induced with regard to the film inertia effect. The film damping coefficients and optimum design parameters are calculated. When unbalance parameter U is greater than 0.2, the nonlinear vibration such as "Jump" phenomena appears in the vicinity of rotor critical speed. At this time, the increases of bearing parameter U, journal distance S, Reynolds number Re can control this unstable vibration. The experimental results show that SFD hearing and rotor system which are designed according to the design parameters in the stable region are operated stably in rotational speed 9,600rpm without nonsynchronous behavior.

• Earthquakes and Structures
• /
• v.13 no.3
• /
• pp.279-288
• /
• 2017

Having the ability to keep on yielding stable solutions in problems involving high potential of instability, composite time integration methods have become very popular among scientists. These methods try to split a time step into multiple sub-steps so that each sub-step can be solved using different time integration methods with different behaviors. This paper proposes a new composite time integration in which a time step is divided into two sub-steps; the first sub-step is solved using the well-known Newmark method and the second sub-step is solved using Simpson's Rule of integration. An unconditional stability region is determined for the constant parameters to be chosen from. Also accuracy analysis is perform on the proposed method and proved that minor period elongation as well as a reasonable amount of numerical dissipation is produced in the responses obtained by the proposed method. Finally, in order to provide a practical assessment of the method, several benchmark problems are solved using the proposed method.

• Journal of Korean Neurosurgical Society
• /
• v.45 no.5
• /
• pp.300-302
• /
• 2009

The authors present a rare case of severe vasospasm following the rupture of arteriovenous fistula. On initial CT scan, hematoma in the corpus callosum and left inferior frontal region with surrounding cerebromalacia and all ventricles without apparent subarachnoid hemorrhage were seen. Angiograms showed arterivenous fistula but did not show cerebral vasospasm. Thirteen days after admission the neurological state of patient suddenly deteriorated and bilateral motor weaknesses developed. Following angiograms revealed severe narrowing on the supraclinoid portion of bilateral internal carotid arteries, bilateral anterior cerebral arteries and bilateral middle cerebral arteries. Transluminal angioplasty and intra-arterial papaverine infusion were performed. The patient remained stable with moderate neurologic deficits.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.938-943
• /
• 1998

The induction motor of the electric vehicles is controlled based on the vector control method to obtain good torque control characteristics. In the conventional vector control system, the field exciting current should be kept on a constant value to keep a stable flux level. This method has a liability that core loss becomes increasing at the light load region. To solve this liability, the efficiency maximizing control method of the vector controlled induction motor is proposed in thid paper. We developed light weight water cooled 60kW induction motor drive system which adopts our method and fabricated a conversion electric car for actual vehicle test. We demonstrate the usefulness of drive system by comparing its driving mode with conventional field oriented system and an efficiency maximizing controlled induction motor.

• Journal of Communications and Networks
• /
• v.10 no.1
• /
• pp.1-4
• /
• 2008

This paper reports the design of a multiwavelength fiber laser source that utilizes a linear cavity of hybrid Brillouin/Erbium fiber laser (BEFL). The output power, threshold power and free running cavity modes were investigated against the pump powers. The structure exhibited low threshold operation of 4 mW at 2.3 mW injected Brillouin pump power. The optimization of Brillouin pump wavelength, power and Erbium gain led to a maximum possible number of channels generated. Simultaneous and stable operation of 21 channels with 10.88 GHz channels spacing were obtained from this architecture at 1 mW injected Brillouin pump power and 90 m W Erbium doped fiber pump power in the 1555 nm region.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.16 no.3
• /
• pp.208-215
• /
• 2016

The lithography hotspot detection process is crucial for semiconductor design development process. But, the lithography hotspot detection using optical simulation method takes much time and it slowdown the layout design development cycle. Though the geometry based approach is introduced as an alternative, it still revealed low detection performance and sophisticated framework. To solve this problem, we introduce a deep convolutional neural network based hotspot detection method. Our method made better results in ICCCAD 2012 dataset. To reach this score, we used lots of technical effort to improve the result in addition to just utilizing the nature of convolutional neural network. Inspection region reduction, data augmentation, DBSCAN clustering helped our work more stable and faster.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.323-330
• /
• 1999

The conventional analysis for the numerical computation of fluid film thickness with elastic deformation of contact region. is performed by Newton-Rephson method for its 18st convergence characteristics. However, both high load and relatively low sliding velocity frequently make it impossible for Newton-Rahpson method to get both converged and stable solutions. In particular, this method cannot provide converged Solution under the condition of high load above 1.0 GPa which frequently occurs in line contact of EHL problem. Multigird multi-level method for the solver of non-linear partial differential equation including solid deformation is preferred to Newton-Rshpson method for better convergence and stability and is applied to line contact EHL behavior in this study.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.572-577
• /
• 1996

Stereolithography is a process used to rapidly produce stereolithographic parts directly from three dimensional CAD models. However, design methodologies necessary to create components to be built by stereolithography are different from those required by conventional machining processes. A case in point is the nescessity of support structures, which are used to support a component during the building the build but are removed once building and curing are complete. Support structures are required to anchor the component to the platform and to prevent sagging or disortion. This paper deals with the specially maintained SupportMap data structure to find some region which need support structures. Interferences between support structures and parts, as well as among support structures are checked and statically stable regions are searched to remove the surplus support structures. Cross shaped tooth profiles are designed for easy eliminating the support structures.

• Applied Science and Convergence Technology
• /
• v.24 no.2
• /
• pp.41-46
• /
• 2015

Transparent conductive oxides (TCOs) are essential material in optoelectronics such as solar cells, touch screens and light emitting diodes. Particularly TCOs are attractive material for infrared cut off film due to their high transparency in the visible wavelength range and high infrared reflectivity. Among the TCO, Indium tin oxide has been widely used because of the high electrical conductivity and transparency in the visible wavelength region. But ITO has several limitations; expensive and low environmental stability. On the other hands, fluorine doped tin oxide (FTO) is well known for low cost, weather ability and stable in acidic and hydrogen. In this study, two different magnetron sputtering techniques with RF and DC modes at room temperature deposition of FTO thin film was conducted. The change of oxygen content is influence on the topography, transmittance and refractive index.