• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.54-54
• /
• 2008

$Eu^{2+}$, $Nd^{3+}$ co-doped $BaAl_2O_4$ are known as a long afterglow phosphor. We found that $Eu^{2+}$-doped $BaAl_2O_4$ showed ptotoconductivity in the range of UV and visual light. In this study, $BaAl_2O_4$:Eu thin film has been prepared by RF sputtering method and a sensing characteristics to UV and visual light was performed. Only $Eu^{2+}$ and $Nd^{3+}$ co-doped $BaAl_2O_4$ powders and targets for deposition were prepared by a convention solid state method, and the deposition was performed in a reducing $H_2$-Ar mixture gas on Si substrates. The observation of crystalline phase and morphology of the sputtered film were performed using XRD, EDX. The photoluminescence and photocurrent to UV and visual light were measured simultaneously using 300W-Xe solar simulator as a light source. It was confirmed that the photocurrent induced by irradiation of light showed a linear relationship to the light intensity.

• Journal of the Korean Ceramic Society
• /
• v.35 no.8
• /
• pp.871-877
• /
• 1998

$CuInSe_2$ thin films have been formed by two-step method in which Cu-In alloy layer was first deposited and then it was selenized. Cu-In alloy layers were deposited by co-sputtering method at ambient tem-perature. XRD analysis showed that both of $Cu_{11}In_{9}$ and CuIn$_2$ phases were formed from these films. $Cu_{11}In_{9}$ peak intensity was increased increased with varying the composition from In-rich to Cu-rich. The metallic layers were selenized either in low pressure of 10 mTorr or in atmospheric pressure(AP) Less compounds of Cu-Se and In-Se were observed during the early stage of selenization and also $CuInSe_2$ thin films selenized in vacuum showed lower roughness larger grain size and better crystallinity than those in AP.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.450-450
• /
• 2006

Organic light-emitting diodes (OLED) as pixels for flat panel displays are being actively pursued because of their relatively simple structure, high brightness, and self-emitting nature [1, 2]. The top-emitting diode structure is preferred because of their geometrical advantage allowing high pixel resolution [3]. To enhance the performance of TOLEDs, it is important to deposit transparent top cathode films, such as transparent conducting oxides (TCOs), which have high transparency as well as low resistance. In this work, we report on investigation of the characteristics of an indium tin oxide (ITO) cathode electrode, which was deposited on organic films by using a radio-frequency magnetron sputtering method, for use in top-emitting organic light emitting diodes (TOLED). The cathode electrode composed of a very thin layer of Mg-Ag and an overlaying ITO film. The Mg-Ag reduces the contact resistivity and plasma damage to the underlying organic layer during the ITO sputtering process. Transfer length method (TLM) patterns were defined by the standard shadow mask for measuring specific contact resistances. The spacing between the TLM pads varied from 30 to $75\;{\mu}m$. The electrical properties of ITO as a function of the deposition and annealing conditions were investigated. The surface roughness as a function of the plasma conditions was determined by Atomic Force Microscopes (AFM).

• Journal of the Korean institute of surface engineering
• /
• v.46 no.5
• /
• pp.187-191
• /
• 2013

Niobium nitride (NbN) films were deposited on AISI 304 stainless steels by inductively coupled plasma (ICP) assisted dc magnetron sputtering method at different ICP powers, and the effects of ICP power on the phase formation, mechanical and chemical properties of the films were investigated. X-ray diffraction analysis (XRD) and field emission scanning electron microscopy (FESEM) were used to analyze the crystal structure and micro-knoop hardness was used to measure the hardness of the films. Also, 3-D mechanical profiler and a ball-on-disk wear tester were used to measure the thickness of the films and to estimate wear characteristics, respectively. The thickness of the films decreased but their hardness increased with increasing ICP power, and it was confirmed that only cubic ${\delta}$-NbN(200) remained at high ICP power. At lower ICP powers, a mixture of the hexagonal ${\delta}^{\prime}$-NbN and cubic ${\delta}$-NbN phases was obtained in the films and the hardness decreased. The corrosion potential value increased gradually with increasing ICP power, but the changes of ICP power did not significantly influence the overall corrosion resistance.

• Korean Journal of Metals and Materials
• /
• v.46 no.4
• /
• pp.249-256
• /
• 2008

0.5 wt% Al doped ZnO thin films (AZO) were prepared on glass substrates using RF magnetron sputtering method. Thin films were grown at substrate temperature of $250^{\circ}C$, RF power of 75W, working pressure of 10 mTorr, by changing the $O_2/Ar$ pressure ratio from 0% to 16.7%. The effects of oxygen partial pressure during the deposition process on structural and optical properties of the films were investigated using XRD, SEM, AFM, EPMA and UV-visible spectroscopy. All the AZO thin films were grown as hexagonal wurtzite phase with the c-axis preferred out-of-plane orientation. The surface roughness and grain size of AZO films decreased with increasing oxygen ratio from 10.6 nm to 3.2 nm and 94.9 nm to 30.9 nm, respectively. On the other hand, the transmittance and band gap energy of the AZO films increased from 84.7% to 92.6% and 3.24 eV to 3.28 eV, respectively with increasing the $O_2/Ar$ pressure ratio.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.3
• /
• pp.5-8
• /
• 2007

All three buffer layers of $Y_2O_3$, YSZ, and $CeO_2$ have been deposited on the biaxially textured metal substrates using rf-sputtering method, The first 50-70nm thick $Y_2O_3$ films were grown epitaxially on biaxially textured metal substrates as a seed layer and followed by the diffusion barrier ${\sim}100nm$ thick YSZ and subsequent capping layer ${\sim}200nm$ thick $CeO_2$ deposited epitaxially on top of $Y_2O_3$ seed layer. The epitaxial orientation of all three layers were all (100) grown with rocking curve Full Width at Half Maximum(FWHM) of $4-5^{\circ}$ and in plane phi-scan FWHM of $6-8^{\circ}$ using X -ray diffraction analysis. The NiO phases formed during the $Y_2O_3$ seed layer deposition seem to degrade the crystallinity and roughen the surface morphology of the following layer observed by AFM(Atomic Force Microscopy). The buffered tapes were used as substrates for long length YBCO coated conductors with high critical current density $J_c$. The five multi-turn of metal tapes was employed to increase the thickness of films and production rate to compensate the low growth rate of rf-sputtering method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.588-593
• /
• 2023

The advantage of OTFT technology is that large-area circuits can be manufactured on flexible substrates using a low-cost solution process such as inkjet printing. Compared to silicon-based inorganic semiconductor processes, the process temperature is lower and the process time is shorter, so it can be widely applied to fields that do not require high electron mobility. Materials that have utility as electrode materials include carbon that can be solution-processed, transparent carbon thin films, and metallic nanoparticles, etc. are being studied. Recently, a technology has been developed to facilitate charge injection by coating the surface of the Al electrode with solution-processable titanium oxide (TiOx), which can greatly improve the performance of OTFT. In order to commercialize OTFT technology, an appropriate method is to use a complementary circuit with excellent reliability and stability. For this, insulators and channel semiconductors using organic materials must have stability in the air. In this study, carbon-doped Mo (MoC) thin films were fabricated with different graphite target power densities via unbalanced magnetron sputtering (UBM). The influence of graphite target power density on the structural, surface area, physical, and electrical properties of MoC films was investigated. MoC thin films deposited by the unbalanced magnetron sputtering method exhibited a smooth and uniform surface. However, as the graphite target power density increased, the rms surface roughness of the MoC film increased, and the hardness and elastic modulus of the MoC thin film increased. Additionally, as the graphite target power density increased, the resistivity value of the MoC film increased. In the performance of an organic thin film transistor using a MoC gate electrode, the carrier mobility, threshold voltage, and drain current on/off ratio (I_on/I_off) showed 0.15 cm²/V·s, -5.6 V, and 7.5×10⁴, respectively.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1501-1503
• /
• 1999

The $(Sr_{0.85}Ca_{0.15})TiO_3$(SCT) thin films are deposited on Pt-coated electrode$(Pt/TiO_2/SiO_2/Si)$ using RF sputtering method. Ag, Cu, Al, Pt films for the formation of top eletrode were doposited on SCT thin films by thermal evaporator and sputtering. The effects of top electodes have be studied on SCT samples with a variety of top electrode materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.63-63
• /
• 2009

Many researchers have been studied as active and transparent electrode using ZnO (Zinc oxide) inorganic semiconductor material due to their good properties such as wide band-gap and high electrical properties compared with amorphous-Si. In this study, we fabricated ZnO films by the RF magnetron sputtering method at a low temperature for a channel layer in thin-film transistor (TFT) and investigated the characteristics of sputtered ZnO films. Also, the electrical properties of TFT using ZnO channel layer such as field effect mobility(${\mu}$), threshold voltage ($V_{th}$), and $I_{on/off}$ ratio are investigated for the application of the display and electronic devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.120-120
• /
• 2009

Ga doped ZnO (GZO) transparent conductive films were deposited on the glass substrates at room temperature by facing target sputtering (FTS) method. The sputtering targets were 100 mm diameter disks of GZO($Ga_2O_3$ 3.w.t%) and Zn metal. The GZO thin films were deposited as a various $PO_2$ (oxygen gas content). Base pressure was $2{\times}10^{-6}torr$, and a working pressure was 1mTorr. The properties of thin films on the electrical and optical properties of the deposited films were investigated by using a four-point probe (Chang-min), a Hall Effect measurement (Ecopia) and an UV/VIS spectrometer (HP). The minimum resistivity of film was $6.5{\times}10^{-4}[{\Omega}-cm]$ and the average transmittance of over 80% was seen in the visible range