• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.998-1001
• /
• 2004

ZnO, $SnO_2$ 타겟 각각의 RF 파워를 50 W, 38 W로 고정시킨 후 combinatorial RF magnetron sputtering법을 사용하여 기판 위치에 따라서 조성 구배를 주어 여러 가지 조성의 Zn-Sn-O(ZTO) 박막을 제작하였다. 시편의 열처리에 따른 물성 변화를 분석하기 위해 Rapid Thermal Annealer(RTA)을 이용하여 450, $650{^\circ}C$의 온도 및 $10^{-2}$ Ton의 진공 분위기에서 각각 1 시간 동안 열처리하였다. XRD 분석 결과 상온에서 제작된 ZTO 박막은 Sn 18 at%의 조성을 갖는 시편을 제외하고 모두 비정질상으로 나타났다. $450^{\circ}C$에서 열처리 후 구조적인 변화는 보이지 않았으나, 캐리어 농도와 이동도는 증가하였으며 Sn 54 at%의 조성에서 최고 $25.4cm^2/Vsec$의 전자 이동도를 나타내었다. $26{\leq}Sn$ $at%{\leq}65$의 조성 범위를 갖는 박막은 가시광 영역에서 80 % 이상의 투과도를 가졌으며 $650^{\circ}C$에서 결정화가 되면서 투과도가 증가하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.316-316
• /
• 2008

Using an evaporation method, $SiO_2$ was deposited as a buffer layer between a flexible PET substrate and a ITO film deposited by DC magnetron sputtering and electro-optical properties were investigated with thickness variance of $SiO_2$ layers. After coating a $SiO_2$ layer and a ITO film, the ITO/$SiO_2$/PET was heated up to $200^{\circ}C$ and the resistivity and the transmittance were measured by hall effect measurement system and UV/VIS/NIR spectroscopy. As a result of depositing a $SiO_2$ buffer layer, the resistivity increased and the transmittance and adhesion property were enhanced than ITO films with no buffer layers and the resistivity was lowered as $SiO_2$ thickness increased from 50 $\AA$ to 100 $\AA$. It was found that the transmittance was independent of annealing temperature variance in $150^{\circ}C{\sim}200^{\circ}C$ and the resistivity decreased as the temperature increased and especially decreasing rate of the resistivity was higher as the buffer layer thickness was thinner. So under optimized depositing of $SiO_2$ buffer layers and post-annealing of ITO/$SiO_2$/PET, ITO films with enhanced adhesion, electro-optical properties can obtained.

• ETRI Journal
• /
• v.38 no.2
• /
• pp.265-271
• /
• 2016

We analyzed the interface characteristics of Zn-based thin-film buffer layers formed by a sulfur thermal cracker on a $Cu(In,Ga)Se_2$ (CIGS) light-absorber layer. The analyzed Zn-based thin-film buffer layers are processed by a proposed method comprising two processes - Zn-sputtering and cracker-sulfurization. The processed buffer layers are then suitable to be used in the fabrication of highly efficient CIGS solar cells. Among the various Zn-based film thicknesses, an 8 nm-thick Zn-based film shows the highest power conversion efficiency for a solar cell. The band alignment of the buffer/CIGS was investigated by measuring the band-gap energies and valence band levels across the depth direction. The conduction band difference between the near surface and interface in the buffer layer enables an efficient electron transport across the junction. We found the origin of the energy band structure by observing the chemical states. The fabricated buffer/CIGS layers have a structurally and chemically distinct interface with little elemental inter-diffusion.

• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.115-120
• /
• 2003

We have developed laser micro-machining technology for fabrication of the micro thin-film inductors. After the thin layers of FM/M/FM films were coated to the silicon substrate by using the conventional sputtering method, the new laser machining was applied to the patterning process that used to be carried out by the semiconductor lithography procedure. A CW Nd:YAG laser operating in TEM$\sub$00/ mode was actively Q-switched to obtain the very short pulse of 200 ns. The laser micro-machining process with pulse energy and repetition rate have been optimized as 5 mJ/pulse and 5 kHz, respectively, to obtain the line resolution as fine as 20 $\mu\textrm{m}$.

• Journal of Sensor Science and Technology
• /
• v.5 no.4
• /
• pp.71-79
• /
• 1996

The mechanism of electrochemical polymerization of polypyrrole was analyzed using Q.C.A. via measuring the resonant frequency and resonant resistance of AT-cut quartz crystal, whose electrodes were fabricated with indium tin oxide by sputtering method. The quantity of polymerized polypyrrole was able to be calculated from the resonant frequency and the viscoelasticity of polypyrrole film from resonant resistance. We found that the elastic film is formed at the first stage of the polymerization, but transformed to viscoelastic film later and that this transition repeated at some point. From these results, it was confirmed that the rheological characteristics of electrochemically polymerized polypyrrole thin film can be analyzed using Q.C.A.

• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.81-86
• /
• 1997

Platinum thin films were deposited on $SiO_{2}/Si$ and $Al_{2}O_{3}$ substrates by DC magnetron sputtering for RTD (resistance thermometer devices) temperature sensors. The resistivity and sheet resistivity of these films were decreased with increasing the annealing temperature and time. We made Pt resistance pattern on $Al_{2}O_{3}$ substrate by lift-off method and fabricated Pt-RTD temperature sensors by using W-wire, silver epoxy and SOG(spin-on-glass). In the temperature range of $25{\sim}400^{\circ}C$, we investigated TCR(temperature coefficient of resistance) and resistance ratio of Pt-RTD temperature sensors. TCR values were increased with increasing the annealing temperature, time and the thickness of Pt thin films. Resistance values were varied linearly within the range of measurement temperature. At annealing temperature of $1000^{\circ}C$, time of 240min and thin film thickness of $1{\mu}m$, we obtained TCR value of $3825ppm/^{\circ}C$ close to the Pt bulk value.

• Journal of Sensor Science and Technology
• /
• v.29 no.4
• /
• pp.232-236
• /
• 2020

Three-dimensional (3D) multilayered Pt electrodes were fabricated to develop a porous electrode using a pattern-transfer printing process. The Pt thin films were deposited using a transferred sputtering pattern having a 250 nm line width on the substrate, and the uniform line patterns were efficiently transferred using our proposed method. Temperature-programmed desorption (TPD) analyses were used to evaluate the porosity of the electrodes. It was possible to distinguish between two resolved maxima at 168 and 227 ℃, which could be described in terms of desorption reactions on the Pt (111) planes. The results of the TPD analysis of the 3D and multilayered Pt electrodes prepared through transfer printing were compared to those of an electrode fabricated through screen printing using a commercial Pt-carbon paste commonly used as porous electrodes. It was confirmed that the 3D multilayered electrodes exhibited a desorption concentration approximately 100 times higher than that of the Pt-carbon composite electrode, and the desorption concentration increased by approximately 0.02 mg/mol per layer. The 3D multilayered electrode effectively functions as a porous electrode and a catalyst.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.201-206
• /
• 2000

Effects of the post-annealing temperature of CeO$_2$ buffer layers on the properties of YBCO films on CeO$_2$-buffered sapphire were investigated. 45 nm-thick CeO$_2$ buffer layer was prepared in-situ on r-cut sapphire using an on-axis rf magnetron sputtering method, which was later post-annealed at temperatures between 950$^{\circ}$C and 1100$^{\circ}$C in an oxygen-flowing environment. YBCO films were prepared on CeO$_2$-buffered sapphire (CbS), for which the surface morphology, crystal structures and electrical properties of the YBCO films were studied. YBCO films on post-annealed CbS appeared to have better properties than those on as-grown CbS with regard to the morphological, structural and electrical properties when the YBCO films were prepared on CeO$_2$ buffer layer post-annealed at temperatures of 1000 - 1050$^{\circ}$C. A TE$_{011}$ mode rutileloaded cylindrical cavity resonators was fabricated with the YBCO films placed as the endplates, for which the unloaded Q of the resonator was measured. It turned out that the resonator with the endplates prepared from the YBCO films on postannealed CbS at 1000 $^{\circ}$C showed the highest unloaded Q with the value more than 8 ${\times}$ 10$^5$ at 30 K and 8.6 CHz, revealing that the YBCO films on post-annealed CbS at 1000$^{\circ}$C the temperature could be the lowest among the YBCO films on post-annealed CbS.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.5
• /
• pp.251-255
• /
• 2009

Nanocomposites based on coupling $TiO_2$ matrix with nanosized noble metals (Pt,Au) particles exhibited promising photoelectrode properties. The $M/TiO_2$ (M=Pt,Au) nanocomposite thin films were deposited on quartz and ITO glass substrates using a co-sputtering method. $TiO_2$ in rutile form is the dominant crystalline phase for as-deposited nanocomposite films. Along with heat treatment up to $600^{\circ}C$, XRD peaks of the rutile phase as well as those of noble metal increased in intensity and decreased in width, indicating the growth of crystallites. The anodic photocurrents of $M/TiO_2$ (M=Au,Pt) thin films were observed not only in the UV range but also in the visible light range. The photocurrent of the nanocomnosite films extended to the visible light region by dispersion of nano-sized noble metal in the $TiO_2$ matrix.

• Korean Journal of Materials Research
• /
• v.21 no.9
• /
• pp.491-496
• /
• 2011

Transparent conducting oxides (TCOs) used in the antireflection layer and current spreading layer of heterojunction solar cells should have excellent optical and electrical properties. Furthermore, TCOs need a high work function over 5.2 eV to prevent the effect of emitter band-bending caused by the difference in work function between emitter and TCOs. Sn-doped $In_2O_3$ (ITO) film is a highly promising material as a TCO due to its excellent optical and electrical properties. However, ITO films have a low work function of about 4.8 eV. This low work function of ITO films leads to deterioration of the conversion efficiency of solar cells. In this work, ITO films with various Zn contents of 0, 6.9, 12.7, 28.8, and 36.6 at.% were fabricated by a co-sputtering method using ITO and AZO targets at room temperature. The optical and electrical properties of Zn-doped ITO thin films were analyzed. Then, silicon heterojunction solar cells with these films were fabricated. The 12.7 at% Zn-doped ITO films show the highest hall mobility of 35.71 $cm^2$/Vsec. With increasing Zn content over 12.7, the hall mobility decreases. Although a small addition of Zn content increased the work function, further addition of Zn content over 12.7 at.% led to decreasing electrical properties because of the decrease in the carrier concentration and hall mobility. Silicon heterojunction solar cells with 12.7 at% Zn-doped ITO thin films showed the highest conversion efficiency of 15.8%.