• Macromolecular Research
• /
• v.12 no.4
• /
• pp.374-378
• /
• 2004

The biodegradable and biocompatible poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), a copolymer of microbial polyester, was fabricated as nanofibrous mats by electrospinning. Image analysis of the electrospun nanofibers fabricated from a 2 wt% 2,2,2-trifluoroethanol solution revealed a unimodal distribution pattern of fiber diameters with an observed average diameter of ca. 185 nm. The fiber diameter of electrospun fabrics could be controlled by adjusting the electro spinning parameters, including the solvent composition, concentration, applied voltage, and tip-to-collector distance. Chondrocytes derived from rabbit ear were cultured on a PHBV cast film and an electrospun PHBV nano-fibrous mat. After incubation for 2 h, the percentages of attached chondrocytes on the surfaces of the flat PHBV film and the PHBV nanofibrous mat were 19.0 and 30.1 %, respectively. On the surface of the electrospun PHBV fabric, more chondrocytes were attached and appeared to have a much greater spreaded morphology than did that of the flat PHBV cast film in the early culture stage. The electro spun PHBV nanofabric provides an attractive structure for the attachment and growth of chondrocytes as cell culture surfaces for tissue engineering.

• Macromolecular Research
• /
• v.16 no.7
• /
• pp.626-630
• /
• 2008

Poly(vinyl pyrrolidone) was used successfully to control the size and distribution of silver nanoparticles generated on inorganic silica nanofibers. The inorganic nanofibers were electro spun using sol-gel chemistry of silicates, and the diameter of the prepared nanofibers was unaffected by adding up to 7% of poly(vinyl pyrrolidone). The silver ions, in the form of silver nitrate, were introduced into the silica nanofibers and reduced to metallic silver by ultraviolet irradiation with a subsequent thermal treatment. The size of the generated silver particles was decreased dramatically by adding poly(vinyl pyrrolidone). The size of the silver nanoparticles was 73 nm when no poly(vinyl pyrrolidone) was added but 23 nm with the addition of only 1% of poly(vinyl pyrrolidone). The extent of reduction could be checked by determining the concentration of silver ions leached into water from the silica nanofibers. After thermal treatment of the silica nanofibers, more than 99% of the silver remained in the nanofibers, indicating almost complete reduction of the silver ions to silver metal.

• Animal cells and systems
• /
• v.7 no.1
• /
• pp.35-41
• /
• 2003

The principal fibers used in constructing the cocoon in the garden spider, Argiope aurantia, are large-diameter fibers developed from tubuliform glands and small-diameter fibers presumed to be spun by the aciniform silk glands. Scanning electron micrographs of the large-diameter fibers on both surfaces of the cocoon clearly reveal their fine structural differences. While the silk fibers on the inner surface have smooth and homogeneous appearances, each fiber on the outer surface represents a multicomponent internal structure. Examination of each fibers using transmission electron microscope also provides additional evidence that the multicomponent fibers contain numerous electron lucent fibrils embedded in an amorphous electron dense matrix. It has been also revealed that two types of secretory granules presumed to be the precursors of tubuliform fibers are closely related to the production of distinct coloration in luminal contents - brownish and yellowish components. Moreover, these electron-dense granules, possibly precursor of fibrillar component, and electron-lucent granules, possibly precursor of matrix component, are densely packed and remain close to each other without fusion. It is critical evidence that the individual tubuliform fiber is not only heterogeneous and multicomponent but also takes place in a variety at manners throughout the length of the gland.

• Fibers and Polymers
• /
• v.7 no.3
• /
• pp.317-322
• /
• 2006

Reduction of yam hairiness by nozzles in ring spinning and winding is a new approach. Simulation of the airflow pattern inside the nozzles provides useful information about actual mechanism of hairiness reduction. The swirling air current inside the nozzles is capable of wrapping the protruding hairs around the yam body, thereby reducing yam hairiness. Since production rate of winding is very high and the process itself increases yarn hairiness any method to reduce the hairiness of yarns at this stage is a novel approach. A CFD (computational fluid dynamics) model has been developed to simulate the airflow pattern inside the nozzles using Fluent 6.1 software. In this study, both S- and Z-type nozzles having an axial angle of 500 and diameter of 2.2 mm were used for simulation studies. To create a swirling effect, four air holes of 0.4 mm diameter are made tangential to the inner walls of the nozzles. S- and Z-twisted yams of 30 tex were spun with and without nozzles and were tested for hairiness, tensile and evenness properties. The total number of hairs equal to or exceeding 3 mm (i.e. the S3 values) for yam spun with nozzle is nearly 49-51 % less than that of ring yams in case of nozzle-ring spinning, and 15 % less in case of nozzle-winding, while both the yarn types show little difference in evenness and tensile properties. Upward airflow gives best results in terms of hairiness reduction for nozzle-ring and nozzle wound yams compared to ring yarns. Yarn passing through the centre of the nozzle shows maximum reduction in S3 values.

• Textile Coloration and Finishing
• /
• v.34 no.1
• /
• pp.20-26
• /
• 2022

Centrifugal spinning is an emerging technique for fabricating micro-to-nano-fibers in recent years. To obtain fibers with the desired size and morphology, it is necessary to configure and optimize the parameters used in centrifugal spinning. In this study, it was controlled by changing the solution's concentration (7.5, 10, and 12.5 wt.%) and disk's rotational velocity (6,000, 8,000, and 10,000 rpm) to prepare centrifugal spun nano-filter. The morphological property, air permeability, and dust collection efficiency of the PVA/PP bi-layer nanoweb prepared by centrifugal spun PVA on the PP micron nonwoven substrate are studied using a field emission scanning electron microscope, an air permeability tester, and a filter tester equipment, and the analysis results indicate that it is suitable as a nano-filter when the concentration of PVA solution is 10 wt.% and the rotational velocity of the disk is 8,000 rpm. The resultant reduced diameter and uniform fibers also proved that an excellent dust collection efficiency filter could be made.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.98-101
• /
• 2005

The mechanical and thermal properties of PAN-based/Rayon-based carbon fabrics interply hybrid composite materials have been studied. Mechanical properties was improved with increasing amount of continuous PAN-based carbon fabrics. The erosion rate was calculated through torch test. The thermal conductivity of hybrid of spun PAN-based/continuous rayon-based carbon fabric is lower than others.

• Textile Coloration and Finishing
• /
• v.17 no.1
• /
• pp.38-44
• /
• 2005

Oxidation method was used to extract S-keratose from wool. Wool was treated with performic acid and soluble fraction(S-keratose) was collected by evaporating the solvent. S-keratose and Nylon 6 were dissolved in formic acid at the ratio of 100/0, 80/20, 50/50, 20/80, and 0/100, and S-keratose/Nylon 6 web of sub-micron size was made by electro-spinning technique. SEM, EA, FT-IR, XRD, and TGA were used to characterize the properties of S-keratose/Nylon 6 solutions and electrospun fibers. As the Nylon 6 content increased, viscosity, conductivity of the electrospinning solution and the diameter of spun fiber increased. Electrospun nonwoven webs have the same S-keratose/Nylon 6 ratios of the spinning solutions. The crystalline structures of S-keratose and Nylon 6 existed separately in the electrospun webs. Thermal stability of the webs increased due to Nylon 6 content.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1914-1916
• /
• 1997

광섬유 간섭계를 이용하여 급속응고 리본 및 박막의 자기변형을 측정하였다. 급속응고 리본인 METGLAS 2826MB의 자기변형값은 보고된 값과 매우 잘 일치하였다. 또한 광섬유에 박막코팅된 거대 자기변형재료의 하나인 Sm-Fe계 합금의 자기변형값을 측정하였다.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.2
• /
• pp.541-546
• /
• 2011

In this study, conjugate fibers were prepared from 1,4-cyclohexanedimethanol-modified polyethylene terephthalate (PET) resin using side by side conjugate spinning, sea-island type conjugate spinning, and split type conjugate spinning methods, and the properties of the conjugate fibers were investigated via several techniques. When viscosity increased, the tenacity of side by side conjugate fibers was increased, whereas elongation decreased. The sea-island conjugate fibers showed lower weight loss and surface color difference (K/S) values relative to that of regular PET fibers at the same conditions. The SEM results indicate that orange type spilt readily produced at a temperature range of 120 - 140$^{\circ}C$.

• Fibers and Polymers
• /
• v.6 no.2
• /
• pp.139-145
• /
• 2005

The paper reports the physical and mechanical properties of hand-woven carpets, which have been put under static force. Two groups of wool fibres, from two parts of Iran, were prepared to spin pile yams for the carpets. Each group of the fibres included both conventional and tanned wool. Then two yam counts, $N_m$ = 4/2 and 6/2, were spun for two different knot densities. After weaving the carpets, they were put under static force and their thickness variations were measured and plotted against time, in logarithm scale. The resiliency of the carpets piles after eliminating the static force, were measured and plotted against time, in logarithm scale, too. The results were compared to each other and analysed with respect to parameters such as the type and quality of the wool fibres as well as knot density of the carpets.