• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.40-45
• /
• 2007

Modal analysis or modal test is a routine process to get the modal parameters of a dynamic system. The modal parameters include the natural frequencies, damping ratios and mode shapes. This paper presents a method that can derive the equations of motion for a dynamic system from the modal parameters obtained by the modal analysis or modal test. The present method based on the relation between the eigenvalues and eigenvectors of the state space equation derives the mass, damping and stiffness matrices of the system. The numerical verifications for the simple mass-spring-damper system and the cantilevered beam prove the efficiency and accuracy of the present method.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1708-1713
• /
• 2003

The acceptance test of KTX has been performed in Korea. During the test, lateral vibration of carbody over the accepted value called swat was found. KTX has 20 car trainsed formation whose trailer cars are linked by articulate bogies. So this study is performed to see the effects of long trainsed formation on vehicle dynamics and the train stability by 20 car vehicle model. Firstly the reliable vehicle model which shows well the tendencies appeared in the tests on the high speed test line is required to find the cause of lateral vibration and the countermeasure. Vehicle model was made for the analysis with VAMPIRE. The analysis results show that secondary air spring lateral stiffness is the most significant parameter to cause carbody lateral vibration. Mode analysis results show that he least damped mode shape is similar to the vibration pattern shown in the tests that the amplitude of the motion increases along the train set and decreases in the tail part. For the case of short train formation with 7 or 10cars, sway does not happen. But in the case of longer train formation with 16 or 20 cars, sway was found.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.6
• /
• pp.791-798
• /
• 2006

In order to investigate the NVOC (Natural Volatile Organic Compound) emissions from White Oak, the emission rates of isoprene were measured according to season, weather conditions, and the age of the tree. The analysis of seasonal emission rates showed that the emission rates were the highest during summer followed by spring and fall. The emission rates during summer were found to be nearly 8 times greater than those during fall. In addition, it was observed that the emission rates of isoprene depends on PAR and temperature. Moreover, the effect of age on the emission rates was studied, and the White Oak in the age range of $21{\sim}30$ had higher emission rates than that in the range of $41{\sim}50$. Accordingly, the current result indicates that the isoprene emissions are affected by both meteorological parameter and the age of a tree.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.7 no.2
• /
• pp.170-175
• /
• 1995

To investigate the variation of tidal front in the southwestern sea of Korea, tidal currents were simulated. Tidal front proposed by a criterion parameter (log H/U$^3$)=1.5-2.0 was found further offshore by about 30-50 km in spring tide than in neap tide. This variation is comparable with the observed about 20-60km by satellite image of sea surface temperature (SST). Observed front by satellite is further offshore by about 10-30km than calculated region in southwestern region.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.92-99
• /
• 2008

This paper describes an signal processing method for the hall sensorless position control of ETC control system using a BLDC motor. The proposed ETC control system, which is mainly consisted of a BLDC motor, a throttle plate, a return spring and reduction gear, has a position sensor with an analog voltage output on the throttle valve instead of BLDC motor for detecting rotor position of motor. So the additional commutation information is necessarily needed to control the mentioned ETC module. In order to estimate and determine the commutation state, it is proposed to properly manipulate the resolution of A/D converter considering the mechanical parameter, that is, the number of motor slot and the ratio of reduction gear. Through this method, the estimation of commutation state for operating the system is possible and the discrete signal for commutation is stably obtained. The validity of the method is examined through the experimental results.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.10a
• /
• pp.515-522
• /
• 2001

A simplified method is presented for the computation of eigenvalue and eigenvector derivatives associated with repeated eigenvalues. In the proposed method, adjacent eigenvectors and orthonormal conditions are used to compose an algebraic equation whose order is (n+m)x(n+m), where n is the number of coordinates and m is the number of multiplicity of the repeated eigenvalue. One algebraic equation developed can be computed eigenvalue and eigenvector derivatives simultaneously. Since the coefficient matrix of the proposed equation is symmetric and based on N-space, this method is very efficient compared to previous methods. Moreover the numerical stability of the method is guaranteed because the coefficient matrix of the proposed equation is non-singular, This method can be consistently applied to both structural systems with structural design parameters and mechanical systems with lumped design parameters. To verify the effectiveness of the proposed method, the finite element model of the cantilever beam and a 5-DOF mechanical system in the case of a non-proportionally damped system are considered as numerical examples. The design parameter of the cantilever beam is its width, and that of the 5-DOF mechanical system is a spring.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.14 no.2
• /
• pp.41-48
• /
• 2006

Absorption performance at the vertical interface between refrigerant vapor and liquid solution of $LiBr-H_{2}O$ solution was enhanced by the waves formed due to the interfacial shear stress. The present study investigated experimentally and analytically the improvements of absorption performance in a falling film by wavy film flow. The dynamic parameter was the film Reynolds numbers ranged from 50 to 150. The energy and diffusion equations were solved simultaneously to find the temperature and concentration profiles at the interface of liquid solution and refrigerant vapor. Absorption characteristics due to heat and mass transfer were analyzed for the falling film of the LiBr aqueous solution contacted by refrigerant vapor in the absorber. Absorption performance showed a peak value at the solution flow rate of $Re_{f}>100$. Absorption performance for the wavy film flow was found to be greater by approximately 10% than that for uniform film flow. Based on numerical and experimental results, the maximum absorption rate was obtained for the wavy flow caused by spring insert. The difference between the measured and the predicted results were ranged from 5.8 to 12%.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.20 no.5
• /
• pp.301-310
• /
• 2016

There are differences in seismic behavior between non-skewed bridges and skewed bridges due to in-plane rotations caused by pounding between the skewed deck and its abutments during strong earthquake. Many advances have been made in developing design codes and guidelines for dynamic analyses of non-skewed bridges. However, there remain significant uncertainties with regard to the structural response of skewed bridges caused by unusual seismic response characteristics. The purpose of this study is performing non-linear time history analysis of the bridges using abutment-soil interaction model considering pounding between the skewed deck and its abutments, and analyzing global seismic behavior characteristics of the skewed bridges to assess the possibility of unseating. Refined bridge model with abutment back fill, shear key and elastomeric bearing was developed using non-linear spring element. In order to evaluate the amplification of longitudinal and transverse displacement response, non-linear time history analysis was performed for single span bridges. Far-fault and near-fault ground motions were used as input ground motions. According to each parameter, seismic behavior of skewed bridges was evaluated.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.584-589
• /
• 2001

This paper presents the dynamic parameter design optimization of a suspension seat system using the genetic algorithm. At first, an equivalent 1-D.O.F. mass-spring-damper model of a suspension seat system was constructed for the purpose of its vibration analysis. Vertical vibration response and transmissibility of the equivalent model due to base excitations, which are defined in the ISO's seat vibration test codes, were computed. Furthermore, seat vibration test, that is ISO's damping test, was carried out in order to investigate the validity of the equivalent suspension seat model. Both analytical and experimental results showed good agreement each other. For the design optimization, the acceleration transmissibility of the suspension seat model was adopted as an object function. A simple genetic algorithm was used to search the optimum values of the design variables, suspension stiffness and damping coefficient. Finally, vibration ride performance test results showed that the optimum suspension parameters gives the lowest vibration transmissibility. Accordingly the genetic algorithm and the equivalent suspension seat modelling can be successfully adopted in the vibration ride quality optimization of a suspension seat system.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.718-723
• /
• 2003

The acceptance test of KTX has been performed in Korea. During the test lateral vibration of carbody over the accepted value called sway was found. Many activities have been taken to find the cause of the vibration and the counter-measure. KTX has 20 car trainset formation whose trailer cars are linked by articulate bogies. So this study is performed to see the effects of long trainset formation on vehicle dynamics and the train stability by 16 car vehicle model. Firstly the reliable vehicle model which shows well the tendencies appeared in the tests on the high speed test line is required to find the cause of lateral vibration and the countermeasure. Vehicle model was made for the analysis with VAMPIRE. The analysis results show that secondary air spring lateral stiffness is the most significant parameter to cause carbody lateral vibration. Mode analysis results show that the least damped mode shape is similar to the vibration pattern shown in the tests that the amplitude of the motion increases along the train set and decreases in the tail part. The lateral vibration was appeared at the speed range between 100km/h and 200km/h and disappeared at the low speed and the high speed.