• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.811-813
• /
• 2002

This paper deals with the design of vaccum pump using moving magnet type linear oscillaory actuator based on the design procedure and the characteristic analysis. To improve the starting characteristic, the optimum spring constant is detected and redesigned. The parameter was calculated by Finite Element Method(FEM). In order to dynamic characteristic analysis, Time difference method with voltage and kinetic equation is used. The propritey of the improved model is verified through the experimental.

• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.3
• /
• pp.81-90
• /
• 1988

In recent, the requirement of remote control of hychaulic system is in- creasing. The actuator unit whose output position is proportional to input electrical signal needs a pressure reducer and a dump valve. The pressure reducer provides a constant regulated pressure and filters contaminants. The dump valve supplies proper pressure to the pressure reducer and unloads when the system is not operated. In this thesis, dump valve and pressure reducer with auxiliary function are studied. The choke in the pressure reducer prevents actuator from supplying higher pressure than necessary pressure at beginning, and the spring constant affects on the dynamic characterisics. In dump valve, it is proved that diameter of servo-slide hold and choke diameter of dump plunger affects on damping response.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.5
• /
• pp.419-424
• /
• 2017

The purpose of this study is to develop a virtual testbed capable of predicting the functional performance of a linear electromagnetic actuator for a high voltage relay in order to reduce its development costs and time. The virtual testbed is defined by a multiphysics coupling approach in order to consider the complex interactions of multi-domains such as the solenoid model of electromagnets, the mass-spring-damper model of mechanical systems, the electric circuit model for an external control unit, and the thermal model for predicting temperature variations. The performances of the existing high voltage relay were estimated by the virtual testbed, and then the effectiveness and validation of the proposed testbed were discussed in comparison with the experimental test results. This study showed that the virtual testbed can be applied in design, optimization, and investigation of high voltage relays.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1089-1092
• /
• 1995

A planar vibratory gyroscope using electrostatic actuation and electromagnetic detection is proposed. The gyroscope has large sensitivity and can be fabricated by using surface micrimachining, bulk micromachining and conventional machining technology. In this paper, the gyroscope and the electromagnetic detecting system equations are derived to determine the output characteristics for the planar vibratory gyroscope using electrostatic acturation and electromagnetic detection. The maximum output is obtained when the driving frequencyequals to the detecting frequency. The resonant frequencies of the resonator are determined by the beam stiffness, i.e. the material constants and spring dimensions. The dimensions of the beams are determined using the analytic vibration modelling. The expected resonant frequencies are 200Hz both and the sensitivity is 62mV/deg/sec with 4000 electronic circuit amplifying coefficient for an AC drive voltage of 3V bias voltage of 15V and DC field current of 50 mA.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.755-758
• /
• 1997

In the recent years, as the research and the development of micro and precision machinery become active, the interest of micro actuators using SMA(Shape Memory Alloy) has been increased. The dynamic characteristic analysis of SMA is necessary for actuator application and many common researches report the material characteristics of SMA sufficiently. However, the research of dynamic characteristics is very deficient. In this paper, the helical spring is fabricated with NiTi SMA wire of high resistivity The force, response speed, temperature, and displacement are measured by digital force gauge, infrared thermometer, and laser displacement sensor so that the dynamic characteristics of this SMA actuator is analyzed.

• Smart Structures and Systems
• /
• v.14 no.4
• /
• pp.541-558
• /
• 2014

This paper proposes a new design of shape memory alloy (SMA) wire actuated gripper for open mode operation. SMA can generate smooth muscle movements during actuation which make them potentially good contenders in designing grippers. The principle of the shape memory alloy gripper is to convert the linear displacement of the SMA wire actuator into the angular displacement of the gripping jaw. Steady state analysis is performed to design the wire diameter of the bias spring for a known SMA wire. The gripper is designed to open about an angle of $22.5^{\circ}$ when actuated using pulsating electric current from a constant current source. The safe operating power range of the gripper is determined and verified theoretically. Experimental evaluation for the uncontrolled gripper showed a rotation of $19.97^{\circ}$. Forced cooling techniques were employed to speed up the cooling process. The gripper is simple and robust in design (single movable jaw), easy to fabricate, low cost, and exhibits wide handling capabilities like longer object handling time and handling wide sizes of objects with minimum utilization of power since power is required only to grasp and release operations.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.7
• /
• pp.36-42
• /
• 2002

This paper presents two actuators for levitation using repulsions of permanent magnet and two magnetic levitation tables using the actuators. Here, one actuator for levitation consists of one fixed magnet and one moving magnet, and the other actuator consists of two fixed magnets and one moving magnet. The moving part of the magnetic levitation table contains the moving magnets. repulsive forces caused by the permanent magnets are linearized, and then the equation of motion of the moving part of the table is derived. Using the equation of motion, stability conditions of the moving part are deduced. The stability conditions are analyzed for positional relations of the moving magnets and the minimum number of active control required for stable system. As a result, in the each case of magnetic levitation tables, the requirements for stabilization are expressed by the positional relations and the number of the active controls.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.2
• /
• pp.112-117
• /
• 2012

This paper presents a new stopper mechanism for precision stage by using the Piezoelectric element actuator. The new stage including a new stopper mechanism has the precision positioning mechanism that was been developed for generation displacements with nanometer accuracy and a millimeter dynamic range simulataneouly. The stage is composed not of the mechanical two stopper but of only one Piezoelectric element actuator. The characteristics for the new stage and the stopper have been evaluated experimentally. As the results, we can know that the linearity error characteristics of stage is 30nm in the $20{\mu}m$ measurement range. In addition, the experimental results are confirmed the possibility of the movement in millimeter range.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.168-175
• /
• 2003

In this research, a bridge-type flexure hinge mechanism is developed and optimized to amplify the displacement of a multilayer piezostack. Developed hinge mechanism has three-dimensional structure to reduce link size, so it have high amplification ratio with respect to small size. A flexure hinge is assumed to be 6 degree-of-freedom spring elements and matrix methods are used to model a hinge mechanism. To verify derived matrix model, a displacement and frequency experiments are performed. The analysis result shows that the displacemental error between matrix model and experiments is below 10 percents and the deformation of hinge in parasitic direction should be considered In hinge modeling. Using developed matrix model, an optimal design is performed to maximize the performance of hinge mechanism.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.4
• /
• pp.1-5
• /
• 2011

Electronics in modern life have become more miniaturized and precise and new technology of electronic components has made these trends possible. The explosive demand of electronic components needs more high-speed and accurate performance of manufacturing processes. For high-speed actuation, solenoids, voice coil motors and piezo motors have been used. A solenoid actuator characterized by low price, available small size, and convenience is one of the main components of production equipments requiring compact and high-speed actuators. Since these actuators show millisecond order responsiveness, the improvement of 1~2msec is very important in industrial applications. In this paper, the mathematical model of the solenoid is formulated and simulated using SIMULINK$^{(R)}$. To verify the model, the responses for step input with open-loop control is obtained and compared with the simulation result. In order to improve the responsiveness, Hold voltage method is introduced and optimal value between spring constant and hold voltage is suggested.