• 한국추진공학회지
• /
• 제13권2호
• /
• pp.1-8
• /
• 2009

횡단류로 펄스 분사되는 액체제트의 분무 특성을 연구하기 위하여 35.7 ~ 166.2Hz 범위의 분사 주파수와 횡단류 속도 42 ~ 136 m/s의 조건에서 실험을 수행하였다. 횡단 유동장에서 액체제트의 주된 분열 인자는 압력 펄스 주파수의 영향보다는 횡단류의 항력에 의존하며, 주기적인 압력 진동에 의해 횡단류로 분사된 액체제트는 상하 진동하는 특성을 나타냈다. 또한 액적의 집합체(liquid jet puff)가 횡단류 방향의 액체 제트 표면에 나타났으며, 이러한 두 가지 특성을 통해 유동장의 혼합을 예상할 수 있었다. 압력 펄스 주파수에 의한 SMD 특성은 연속 분사의 층상 구조와 다른 비층상 구조로 나타났으며, 체적 유속은 압력 펄스 주파수가 증가함에 따라 감소하는 경향을 나타내었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.131-135
• /
• 2001

The atomization characteristics of an annular liquid (water) sheet of small radius with a core gas (air) flow were studied. Different sizes of annular gaps (0.2, 0.4 and 0.8 mm) were tested to find the effect of liquid sheet thickness on SMD. The inner diameter of the gas port for the core gas flow was 4 mm. Cross-section averaged SMD was measured for various liquid and gas velocities. Regions of the SMD decrease with the increase of the liquid velocity always existed regardless of the liquid sheet thickness. This attributes to the transition of the flow patterns of spray and also to the aerodynamic interaction between the atomizing gas and the ripples on the liquid sheet surface.

• Nuclear Engineering and Technology
• /
• 제28권4호
• /
• pp.390-396
• /
• 1996

Piping Systems are usually designed for thermal expansion loads based on uniform temperatures at each cross section. However, in lines with low flow rates such as surge lines and spray lines, large transverse temperature gradients have been observed, resulting in too types of additional thermal stresses : (1) local thermal gradient stresses which are independent of routing and supports and (2) gross bending stresses due to induced pipe curvature which are routing and support system dependent. This paper presents a simplified method for analyzing a PER surge line for stratified flow.

• 한국잠사곤충학회지
• /
• 제40권2호
• /
• pp.143-149
• /
• 1998

For the application of silk sericin, silk sericin powders were prepared by various spray dry conditions and the characteristics of silk sericin/polyurethane mixed films were investigated. When the sericin was dried from the solution at higher inlet and outlet temperature, larger sizes of the powder particles were obtained. It was also found that inlet and outlet temperatures were important factors affecting the shape and surface characteristics of sericin power particle. The many holes and empty spaces were observed at the surface and cross section of sericin/PU mixed film. With the increase of the amount of sericin powder in the mixed films, the size and number of holes and empty spaces were increased. The thickness of sericin/PU mixed film was increased with the content of sericin powder. As the portion of sericin powder increase, the tenacity is decreased while the elongation slightly increased.

• 한국표면공학회지
• /
• 제30권6호
• /
• pp.400-405
• /
• 1997

The experimental study has been performed to deposit to deposit chromia powder on magnssium alloy for tribological and mechanical properties. The optimal condition was obtained by changing the spray condition such as working distance and gun power. As ceramics was coated onto the a light metal such as Mg according to the weight reduection of the car engine block, it could acquire that the engine efficiency deu to the weight reduction and properties such as resistance to heat, as well as wear. Coating qualities are discussed with respect to hardness, tribologicalproperty, and microstructure. The tribological and mechanical properties are investigated by using the reciprocal configuration tribometer and microharduess tester. Wear mode is determined by observing the SEM morhpology of wear track and cross section view of wear track.

• 한국분무공학회지
• /
• 제4권4호
• /
• pp.38-45
• /
• 1999

The near field structure of round turbulent jets with initially asymmetric velocity distribution is investigated experimentally. Experiments were carried out using a constant temperature hot-wire anemometry system to measure streamwise velocity in the jets. The measurements were undertaken across the jet at various streamwise stations in a range starting from the jet exit plane and up to a downstream location of twelve diameters. The experimental results include the distribution of mean and instantaneous velocities, vorticity field, turbulence intensity, and the Reynolds shear stress. The asymmetry of the jet exit plane was obtained by using circular cross-section pipes with a bend at the upstream of the exit. Three pipes were used for this study: A straight pipe, 90 and 160 degree-bended pipes. Therefore, at the upstream of the pipe exit, the secondary flow through the bend and the mean streamwise velocity distribution could be controlled by changing the curvature of pipes.

• 연구논문집
• /
• 통권31호
• /
• pp.127-133
• /
• 2001

In chromium electrodeposition, crack is inevitably accompanied by chromium layer. Behavior of crack formation and crack density were different from the plating conditions such as current density, temperature, waveform of applied current and so on. And cracks have an influence on the corrosion resistance of chromium deposit, because corrosion occurs through the network of cracks between deposit and substrate. Therefore, many researches have been achieved in order to remove the cracks in chromium deposit. Formation of double layers, Cr/Cr and Ni/Cr were investigated to increase corrosion resistance of chromium deposit in this study. As pretreatment prior to outer chromium coating, acid pickling and current control method were examined. Cracks in cross-section of each sample were observed with SEM and CASS(Copper modified acetic acid salt spray) test was performed to evaluate corrosion resistance. It was found that corrosion resistance of Cr/Cr and Ni/Cr double layers were superior to Cr or Ni single layer from the results of CASS test.

• 한국표면공학회지
• /
• 제27권3호
• /
• pp.158-165
• /
• 1994

Cu-Cr alloy thin film requires good quality of etching be used for TAB technology. The etched cross sec-tion was clean enough when the etching was performed in 0.1M $FeCl_3$ solution at $50^{\circ}C$. The etching rate was increased with the amount of $KMnO_4$. For enhanced profile of cross section and rate, the spray etchning was found to be superior compared to the immersion etching. A series of experiments were performed to improve the uniformity of the current distribution in electrodeposition onto the substrate with lithographic patterns. Copper was electrodeposited from quiescent-solution, paddle-agitated-solution, and air-bubbled-solution to in-vestigate the effect of the fluid flow. The thickness profile of the specimen measured by profilmetry has the non uniformity at feature scale in quiescent-solution, because of the longitudinal vortex roll caused by the natural convection. However, uniform thickness profile was achieved in paddle-agitated or air bubbled solu-tion.

• 한국표면공학회지
• /
• 제44권5호
• /
• pp.226-231
• /
• 2011

Graphene was coated on STS 316L by electro spray coating method to improve its properties of corrosion resistance and contact resistance. Exfoliated graphite (graphene) was made of the graphite by chemical treatment. Graphene is distributed using dispersing agent, and STS 316L was coated with diffuse graphene solution by electro spray coating method. The structure of the exfoliated graphite was analyzed using XRD and the coating layer of surface was analyzed by using SEM. Analysis showed that multi-layered graphite structure was destroyed and it was transformed into fine layers graphene structure. And the result of SEM analysis on the surface and the cross section, graphene layer was uniformly formed with 3~5 ${\mu}m$ thickness on the surface of substrate. Corrosion resistance test was applied in the corrosive solution which is similar to the PEM fuel cell stack inside. And interfacial contact resistance test was measured to simulate the internal operating conditions of PEM fuel cell stack. The results of measurements show that stainless steel coated with graphene was improved in corrosion resistance and surface contact resistance than stainless steel without graphene coating layer.

• 한국분무공학회지
• /
• 제10권2호
• /
• pp.1-9
• /
• 2005

An experimental study was carried out to obtain the fundamental data about the effects of radical ignition on premixture combustion. A CVC(constant volume combustor) divided into the sub-chamber and the main chamber was used. Numerous narrow passage holes are arranged between the main chamber and the sub-chamber. The products including radicals generated by spark ignition in tile sub-chamber derives the simultaneous multi-point ignition in the main chamber. We have examined the effects of the sub-chamber volume, the diameter and number of passage holes, and the equivalence $ratio({\Phi})$ on the combustion characteristics by means of burning pressure measurement and flame visualization. In a CVC, the overall burning time including the ignition delay became very short and the maximum burning pressure was slightly increased by the radical ignition(RI) method in comparison with those by the conventional spark ignition(SI) method. Combustible lean limit by RI method is extended by ${\Phi}=0.25$ compared with that by SI method. Also, In cases of charging the number and the diameter for the fixed total cross section of the passage holes, combustion period increased significantly at a sub-chamber with a single hole, but those of the other conditions had almost a similar tendency in the sub-chamber with 4 or more holes. regardless of equivalence ratio. Therefore, it was Proved that a critical cross section exists with the number of passage holes.