• Korean journal of applied entomology
• /
• v.59 no.3
• /
• pp.209-215
• /
• 2020

Debates over the ecological and public health impacts of aerial pesticide sprays are increasing. This is particularly true for controlling Monochamus beetles, which are vector insects of pinewood nematodes. In 2017, adult female orb-web spiders, Trichonephila clavata, were sampled from pine forests in Yangsan-si, Gyeongsangnam-do, Korea, where the aerial pesticide spray, fenitrothion or thiacloprid, was used for several decades. The biological traits of the spiders (body weight, body length, carapace width, and total hind leg length) were compared among treatment sites (no-spray, sprayed three times, and sprayed five times), and differences were observed. The body length, carapace width, and total hind leg length of the spiders in the sprayed areas were significantly shorter than in the no-spray area, but there were no differences between the area sprayed three or five times. These results indicate that repeated exposures to an aerial pesticide spray can alter morphological parameters, which influences population-level fitness. Future studies should monitor the spider long-term responses to pesticides (a direct effect) and prey availability (an indirect effect).

• Journal of the Korean institute of surface engineering
• /
• v.29 no.1
• /
• pp.60-72
• /
• 1996

A photoetching process is widely used for small and high precision parts in machinery, electronic and semi-conductor industries. One of the high precision parts, grid is very important part of digitron which use electron display, and it is fabricated by only photoetching process because of high precision. In this study, to develop high precision digitron grid, characteristics of etching solution were investigated with electrochemical test, that was potentiodynamic test and immersion test in the ferric chloride solution and added some additives. Based on the electrochemical etching test, grid was fabricated by continuous photoetching process at various etching condition. From the result of measured line width and etching depth under-cut and etching factor were calculated. For the fabrication of 25$\mu\textrm{m}$ line width, optimal etching condition was etching temperature 40~$45^{\circ}C$, spray pressure 1.5kg/$\textrm{cm}^2$ and etching time 3~4min.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.693-698
• /
• 2001

An experimental study was carried out with an aerated nozzle. This nozzle was well known that the performance of the atomization is better than other ones even though the supplied air pressure is lower than that of them. The purpose of this investigation is to provide the essential information of the aerated nozzle from the nozzle exit. The experimental work was performed in order to analyze the characteristics of the overall flow field from the nozzle exit. The 2-D PDPA system was used to acquire the data in the concerned region. The characteristics of the mean velocity distribution, half-width, and SMD were mainly analyzed. Also the correlation between turbulent kinetic energy and SMD was described with ALR.

• 연구논문집
• /
• s.23
• /
• pp.29-43
• /
• 1993

Photoetching of AISI 304 stainless steel in ferric chloride solution has been studied. This paper investigated on the single side etching characteristics of 304 stainless steel, especially influence of etching temperature, spray pressure of ferric chloride etchant, and etching time with $50\mum$ and $75\mum$ line width photomask.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.254-257
• /
• 2003

본 논문에서는 휴대폰에 사용되는 Multi-band 용 helical antenna 의 radiation pattern 을 체적화하기 위한 방법을 제안하고자 하였다. 일반적으로 GSM 휴대폰에 사용되는 안테나는 GSM, DCS 의 dual band 인 경우가 다수이며 추세에 따라 요즘은 PCS 등을 포함한 triple band 의 안테나가 많이 선호되고 있다. 이러한 multi band antenna 의 radiation pattern 에 영향을 미치는 변수로 본 논문에서는 ground 의 length 와 width 그리고 폴더쪽에 사용되는 LCD 의 ground 와 폴더쪽 기구물에 사용된 EMI spray 등의 변화를 통해 pattern 의 변화를 알아보고 이러한 변수를 조절하여 radiation pattern을 최적화하는 방법에 관하여 논하였다.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1131-1142
• /
• 2000

In an effort to illustrate the global variation of SMD (Sauter mean diameter, or $D_{32}$) and AMD (Arithmetic mean diameter, or $D_{10}$) at five axial downstream locations (i. e., at Z=30, 50, 80, 120, and 170 mm) under the different experimental conditions, the radial coordinate is normalized by the spray half-width. Experimental data to analyze the atomization characteristics concerning with an internal mixing type have been obtained using a PDPA(Phase Doppler Particle Analyzer). The air injection pressure was varied from 40 kPa to 120 kPa. In this study, counterflowing internal mixing nozzles manufactured at an angle of $15^{\circ}$with axi-symmetric tangential-drilled four holes have been considered. By comparing the results, it is clearly possible to discern the effects of increasing air pressure, suggesting that the disintegration process is enhanced and finer spray droplets can be obtained under higher air assist. The variations in $D_{32}$ are attributed to the characteristic feature of internal mixing nozzle in which the droplets are preferentially ejected downward with strong axial momentum, and dispersed with the larger droplets which are detected in the spray centerline at the near stations and smaller ones are generated due to further subsequent breakup by higher shear stresses at farther axial locations. The poor atomization around the centre close to the nozzle exit is attributed to the fact that the relatively lower rates of spherical particles are detected and these drops are not subject to instantaneous breakup in spite of the strong axial momentum. However, substantial increases in SMD from the central part toward the edge of the spray as they go farther downstream are mainly due to the fact that the relative velocity of droplet is too low to cause any subsequent disintegration.

• Laser Solutions
• /
• v.16 no.4
• /
• pp.12-16
• /
• 2013

For mass production of electronic devices, the processing of the printing roll is one of the most important key technologies for printed electronics technology. A roll of printing process, the gravure printing that is used to print the electronic device is most often used. The indirect laser processing has been used in order to produce printing roll for gravure printing. It consists of the following processing that is coating of photo polymer or black lacquer on the surface of printing roll, pattering using a laser beam and etching process. In this study, we have carried out study on the coating and etching for $25{\mu}m$ line width on the printing roll. To do this goals, a $4{\mu}m$ coating thickness and 20% average coating thickness of the coating homogeneity of variance is performed. The factors to determine the thickness and homogeneity are a viscosity of coating solution, the liquid injection, the number of injection, feed rate, rotational speed, and the like. After the laser patterning, a line width of $25{\mu}m$ or less was confirmed to be processed through etching and the chromium plating process.

• Journal of Bio-Environment Control
• /
• v.20 no.2
• /
• pp.101-108
• /
• 2011

The small and medium sprayer has developed to spray well fruit trees and roadside trees with pesticides for pests control within 60 meters. This study was carried out to analyze and evaluate its performance using image processing. While it sprayed with pesticides on the area of 20m in width and 60m in length, it was experimented 5 places by 5m from 0 to 25m width and 6 places by 10m from 10 to 60m length. The experimental image data of each sheet on places were averaged after binarization process. According to the image data, it was sprayed on all working area. However, when sprayer moved 0.3m/s velocity, the place at 15m of width and 30m of length was sprayed more than any other sprayed area, but the place at 15m of width and 60m of length was sprayed less.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.1
• /
• pp.55-59
• /
• 2015

This study demonstrates hybrid-type transparent electrodes for touch screen panels. The hybrid-type electrodes were fabricated by coating carbon nanotubes (CNTs) on metal meshes. To form the metal-meshes, thin films of silver (Ag) were deposited on glass substrates using the sputtering method and then patterned via photolithography to obtain mesh structures whose line width was $10{\mu}m$ and line-to-line spacing was $300{\mu}m$. CNTs were coated on Ag-meshes by using two different methods, such as spray coating and electrophoretic deposition (EPD). For the samples of a Ag-meshes and CNTs-coated Ag-meshes, their surface morphologies, electrical sheet resistances, and visible-range transmittances and reflectances were characterized and compared. The experimental results indicated that the reflectance of Ag-mesh electrodes was substantially reduced by coating of CNTs. Especially, the hybrid electrodes of Ag-meshes with EPD-coated CNTs showed excellent properties such as sheet resistance lower than $20{\Omega}/{\Box}$, transmittance higher than 90 %, and reflectance lower than 8%.

• Journal of ILASS-Korea
• /
• v.13 no.3
• /
• pp.126-133
• /
• 2008

The atomization characteristics of the dual air supplying two-fluid nozzle were investigated experimentally using PIV and PDA systems. The twin-fluid nozzle is composed of three main parts: the feeding injector to supply fluid that is controlled by a PWM (pulse-width modulation) mode, the adaptor as a device with the ports for supplying the carrier and assist air, and the main nozzle to produce sprays. The main nozzle has the swirler with four equally spaced tangential slots, which gives the injecting fluid an angular momentum. The swirl angle in the swirler varied with $0^{\circ}$, $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$. The ratios of carrier air to assist air and ALR (total air to liquid) were 0.55 and 1.23, respectively. The macroscopic behavior of the spray was investigated using PIV system, and the AMD and SMD distributions of the sprays were measured using PDA system. As a result, the SMD distribution increases along the radial distance, and it decreases with the increase of swirl angle in swirler.