• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.411-414
• /
• 2010

초음속 엔진에서 흡입구의 buzz현상은 큰 압력진동과 연소 불안정성 그리고 추력 감소 등을 야기한다. 흡입구의 buzz현상과 액적 분사/연소의 동적인 상호관계를 이해하기 위하여 통합된 비정상 연소수치해석을 수행하였으며, 액적 모사를 위하여 TAB(Taylor Analogy Breakup) model을 적용하였다. 흡입구에서의 충격파거동과 주요 위치에서 압력거동을 분석하고 초음속 엔진 전영역에서의 음향모드를 분석하여 현 시스템의 동적거동을 파악하였다.

• 한국전산유체공학회지
• /
• 제12권1호
• /
• pp.28-34
• /
• 2007

This study evaluates the performance of the packed bed scrubber and proposes the optimization of spray system for improvements of collection efficiency. The packed bed scrubber is used primarily in the semiconductor manufacturing process. The mean diameter of entering solid particles in scrubber is the submicron. The impaction between water droplets and solid particles is an important factor in removing the solid particles. Thus, the coverage area of spray system influences on the collection efficiency. The collection efficiency of a single droplet is calculated through the mathematical model and numerical calculations are performed for coverage area for each nozzle type (Droplet diameters: 500, 319.5, $289.5{\mu}m$) and injected directions (0, 15, $30^{\circ}$). In case of nozzle type 3, the collection efficiency of a single droplet is highest but the collection efficiency of spray system has lowest value because the ratio of flow rate between the gas and water is below 0.1. The results show the coverage area ratio is about 85% in the case of nozzle type 3 and downward sirection $15^{\circ}$. It was shown that a coverage area increase by two times than an existing spray system. In simulation of demister, collection efficiency by demister is predicted about 80% and the pressure drop in demister is below 3.5 Pa.

• Journal of Microbiology and Biotechnology
• /
• 제15권6호
• /
• pp.1178-1182
• /
• 2005

Survival of thermotolerant Lactobacillus reuteri KUB-AC5 in $20\%$ (w/v) skim milk was found to be $11.3\%$ after spray drying by using a pilot scale spray dryer with inlet temperature at $170^{\circ}C$ and outlet temperature at $85^{\circ}C$. The ability of dried cell to produce antimicrobial activity was not affected by the spray drying. The model system for predicting viability of spray-dried L. reuteri KUB-AC5 during long-term storage was established, based on the Arrhenius equation, and verified by experimental data, because the viability of cells during storage can be correlated with storage temperature. The viability during storage at $30^{\circ}C$ declined more rapidly than that storage at $4^{\circ}C$.

• 대한기계학회논문집B
• /
• 제30권4호
• /
• pp.381-388
• /
• 2006

The objective of this study is to predict the etching characteristics using spray characteristics for the optimization on the etching process of Lead-Frame. The etching characteristics such as etching factor, uniformity were investigated on the actual operating conditions. The correlation between the etching characteristics and the spray ones obtained by measurement were analyzed to simulate the etching characteristics according to actual conditions of lead-frame etching process. These conditions of lead-frame process were spray pressure, distance from nozzle tip to substrate, pipe pitch, and nozzle pitch. To improve the etching characteristics in the lead-frame process, effects of the various operating conditions should be understood in detail. The spray characteristics obtained by experiment using PDA system were simulated by the Monte-Carlo method. The etching process model was coded by Java language. It was found that simulation results generally agreed well with the measured results of etching characteristics in lead-frame etching process. The optimal operating parameters were successfully found under variable conditions.

• 한국안전학회지
• /
• 제15권3호
• /
• pp.30-39
• /
• 2000

The present paper deals with the numerical simulation for the spray characteristics with swirling turbulent flows and dilution flows from swirl injectors in a simplified can type of gas turbine combustor. The main objective is to investigate the characteristics of swirling turbulent flows with dilution flows and to provide the qualitative results for the spray characteristics such as the droplet distribution and Sauter Mean Diameter(SMD). The gas-phase equations based on Eulerian approach were discretized by Finite Volume Method, together with SIMPLE algorithm and the Reynolds -Stress-Model. The liquid-phase equations based on Lagrangian method were used to predict the droplet behavior. The results of preliminary test are generally in good agreement with experimental data, and show that the anisotropy exists in the primary zone due to swirl velocity and injected air from primary injector, and then gradually decays due to turbulent mixing and consequently near-isotropy occurs in the region between primary and dilution zones. For the spray characteristics, it is indicated that the swirling flows of primary jet region increase the droplet atomization. In addition, it is showed that the swirling flows at the inlet region lead the air-fuel mixture to be distributed near the igniter and can significantly affect the spray behavior in the primary jet region.

• Korean Chemical Engineering Research
• /
• 제47권6호
• /
• pp.688-694
• /
• 2009

PCB의 먼지 제거용 세정제로 사용되는 스프레이형 세정제를 선정하여 이에 대한 청정도를 평가하였다. 친환경적인 대체 세정제를 채택하기 위해서는 세정제의 세정성, 환경성, 경제성을 평가하여 체계적인 선정절차에 의거하여 도입 및 적용하여야 한다. 객관적이고 효율적인 세정성 평가방법의 정립이 현시점에서 매우 중요하다. 본 연구에서는 여러 세정성 평가 방법들 중 표면관찰평가법인 SEM-EDX(Scanning Electron Microscopy/Energy-Dispersive X-ray) 분석과 적외선열화상카메라(THERMOVISION A20 model)를 이용하여 청정도를 평가하였다. CT-2770 모델의 사운드카드를 $2{\times}2cm$로 잘라내어 스프레이 세정 전과 후의 청정도를 SEM의 이미지 분석을 통해 관찰할 수 있었고 EDX의 성분분석을 통해 먼지의 제거율을 정량화할 수 있었다. 컴퓨터의 P4T-E 모델의 마더보드와 IPC-A-36 모델의 기판을 사용, 오염물로 먼지와 철가루를 사용하여 열화상카메라로 세정 전, 후의 상온과 $50^{\circ}C$ Oven에 방치된 시간의 차이에 따른 온도의 변화를 비교하였다.

• 청정기술
• /
• 제2권1호
• /
• pp.80-95
• /
• 1996

반건식 배연탈황공정에서 사용되는 spray dryer absorber(SDA)에 대한 수치모사를 행하였다. 기본 방정식으로는 기체와 액적의 각 성분들의 물질수지식, 에너지수지식과 액적의 운동 방정식등이 포함되었다. 만들어진 모델은 대부분이 기존의 SPRAYMOD-M보다 실제의 pilot plant data를 더 잘 모사하였다. 실제 pilot plant에서 사용되는 값의 범위 내에서 선정된 공정변수가 SDA의 성능에 미치는 효과를 계산하고, 이를 $SO_2$의 흡수속도, 배연기체의 체류시간, 그리고 액적의 건조시간 및 속도 등에 의해 검토하였다. 또 $SO_2$ 제거율을 두 개의 독립된 공정 변수의 함수로 구하였으며, 그 결과를 3차원 또는 2차원의 등가선으로 표시하여 SDA의 설계에 쉽게 적용될 수 있도록 하였다.

• 한국연소학회지
• /
• 제12권3호
• /
• pp.33-39
• /
• 2007

The present study is mainly motivated to investigate the vaporization, auto-ignition and combustion processes in high-pressure engine conditions. In order to realistically simulate the dimethyl ether (DME) spray dynamics and vaporization characteristics in high-pressure and high-temperature environment, the high-pressure vaporization model is utilized. The interaction between chemistry and turbulence is treated by employing the Representative Interaction Flamelet (RIF) model. The detailed chemistry of 336 elementary steps and 78 chemical species is used for the DME/air reaction. Numerical results indicate that the RIF approach, together with the high-pressure vaporization model, successfully predicts the essential feature of ignition and spray combustion processes.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.77-84
• /
• 2003

It is an aim of this study to perform extensive numerical study for analyzing the anisotropic turbulence effects on spatial and temporal behaviors of diesel sprays after wall impingement. The turbulence model of Durbin is used for comparisons with the $k-\varepsilon$ model. The turbulence-induced dispersions of droplets are considered to describe the anisotropy of turbulence effectively and the spray/wall interactions are simulated using the model of Lee and Ryou. The present study investigates the internal structures of impinging diesel sprays such as Sauter mean diameter (SMD), loca1 droplet velocities, and local gas velocities and also compares the results predicted by two turbulence models with the experimental data. The Durbin's model considering the anisotropy of turbulence predicts both gas and droplet tangential velocities better than the$k-\varepsilon$ model does. It is concluded that the anisotropy of turbulence should be considered in simulating impinging diesel sprays.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1996년도 춘계 학술대회논문집
• /
• pp.137-142
• /
• 1996

A new wall impaction model for spray and its assessment are described in this paper. The gas phase is modelled in terms of the Eulerian continuum conservation equations of mass, momentum, energy and fuel vapour fraction. The liquid phase is modelled following the discrete droplet model approach. The droplet parcel contains many thousands of drops assumed to have the same size, temperature and velocity components. The droplet parcel equations of trajectory, momentum, mass and energy are written in Lagrangian form. The new drop-wall interaction model is proposed, which is based on experimental investigations on individual drops, and it is applied for the general non-orthogonal gird. The model is then assessed through comparison with experiments over a wide range of test conditions of sprays. The results are in good agreement with experimental data.