• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.741-745
• /
• 2001

The necessity of a Z-shape heat pipe may occur in a special application such as a cooling module for an electronic equipment having a limited accessible space. Either of the two end part works as evaporator or condenser and the length of the middle part is 200mm. The heat pipe was made of 3/8 inch copper tube having 60 spiral groove with screw angle of 10 degrees. Water and acetone were used as working fluids. The fill charge ratio of the working fluid was varied for different values of thermal loads. The thermal resistance was calculated based on the temperature measurements along the heat pipe axis. The maximum thermal loads were 80W for water and 100W for acetone heat pipe. The optimum fill charge ratio was identified through a series of experiments.

• Proceedings of the KACD Conference
• /
• 2003.11a
• /
• pp.579-579
• /
• 2003

I. Objectives The aim of this study was to evaluate and compare the effectiveness of sealer placement in simulated root canal extensions using the K file, ultrasonic file, lentulo spiral and EZ-Fill. II. Materials and Methods Forty resin blocks were attained from cutting Endo-training Bloc with diamond saw. In each parallelepiped block, the simulated root canal was made with ＃20, 08taper GT file. After each block was longitudinally split into two halves using mallet and chisel, a standardized groove of 4mm in length, located 2mmapart from the root apex, was prepared on one wall of two halves using the custom-made knife to simulate the canal extensions with various irregularities.(omitted)

• Animal Systematics, Evolution and Diversity
• /
• v.28 no.3
• /
• pp.192-207
• /
• 2012

To supply the morphological and ecological information of oligotrich ciliates in Korea, water samples were seasonally collected in Gwangyang Bay and Jinhae Bay from August, 2010 to February, 2012 and processed by quantitative protargol staining method. As a result, six species belonging to the genus Strombidium Clapar$\grave{e}$de and Lachmann, 1859 are identified: Strombidium emergens Kahl, 1932; S. dalum Lynn et al., 1988; S. epidemum Lynn et al., 1988; S. tressum Lynn et al., 1988; S. bilobum Lynn and Gilron, 1993; S. pollostomum Lynn and Gilron, 1993. These six species were newly reported from Korean coastal waters. Strombidium emergens is a middle sized Strombidium ($20-50{\mu}m$ in length) and has open and deep oral groove to girdle portion. Strombidium dalum is a small sized Strombidium (${\geq}20{\mu}m$ in length), that has torch-like spiral anterior membranelles and an inverted triangles-shaped macronucleus on the posterior pole. The small sized S. epidemum has conspicuous trichites surrounding the girdle portion and ventral membranelles distinctly separated from anterior membranelles. The small sized S. tressum has torch-like spiral and extremely long trichites among the cilia of anterior membranelles. The middle sized S. bilobum has a bilobed macronucleus. Strombidium pollostomum is also a small sized Strombidium but its ventral membranelles are continuously connected with anterior membranelles. The five species except S. emergens occurred frequently over the wide range of water temperatures and salinities.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.6
• /
• pp.91-97
• /
• 2019

Rotating machining unit is a revolutionary product that can process worm shaft or spiral shaft with fast and precise, a rotary type cutting tool, which is attached to automatic lathe and processes spiral groove on outer circumference of round bar. In this work, a study on micro tooth shape modification method of driving gear train in the rotating machining unit was presented. To observe the effect on power transmission characteristics of the driving gear pair, visualize the gear meshing condition and the load distribution on the gear teeth by using the professional gear train analysis program RomaxDesigner. By comparing the repeated analysis results, the effect of micro tooth shape modification on power transmission characteristics on driving gear can be summarized. The optimized gears were fabricated and measured by precision tester as a validation in this research.

• Journal of Biomedical Engineering Research
• /
• v.33 no.4
• /
• pp.202-206
• /
• 2012

In this study, we developed transdermal direct drug delivery device using micro-needle painlessly. We has fabricated micro-needle that is 130 ${\mu}m$ thickness and 250 ${\mu}m$length with 10 ${\mu}m$ spiral groove for rolling down drug. Head part of micro-needle device is composed of 20ea micro-needles, an on-off valve and a protective cap. Glass bottle for containing drug is connected to head part of micro-needle device. We examined the puncture characteristic testing using porcine skin and drug delivery testing using porcine, rat skin with Indian Ink.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.9
• /
• pp.145-150
• /
• 2000

Out-of-sphericity is degree of deformation of an air bearing sphere deviated from a perfect sphere. This paper investigates numerically the effect of out-of-sphericity error on the radial stiffness of an air bearing Three types of out-of-sphericity modes are considered. in this study the stiffness is calculated from pressure distribution at the bearing surface which is obtained by solving th Reynolds equation. in some cases large out-of-sphericity errors are found to improve the stiffnesses of air bearings. This implies that an air bearing of perfect hemispheres is not necessarily of the best performance. Thus much labor and cost in manufacturing air bearings can be saved, In addition the radial stiffness of an air bearing depends greatly on the application direction.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1119-1123
• /
• 1999

In this paper, electrorefining of uranium metal was studied to develop pyrometallurgical processing technology in molten salt system. The reaction between uranium metal and $CdCl_2$ was taken about 3 hours and the uranium metal deposits were obtained in the form of dendrite grown on the cathode surface in every electrotransport experiment. The shapes of dendrite were changed according to the applied voltages. Current efficiency was decreased with the increase of current density. Deposition rate was not changed after 6 hours and its maxium was obtained at $100{\sim}150mA/cm^2$ of current density and about 75 rpm of stirring speed, respectively. Also, the current efficiency was increased with decrease of the pitch of spiral groove curved on cathode.

• Tunnel and Underground Space
• /
• v.26 no.5
• /
• pp.409-417
• /
• 2016

The shale gas is emerging as one of the oil and gas resources which can replace the traditional oil and gas resources. As the shale layer where the shale gas is deposited has low permeability, the hydrofracturing method is required to improve the productivity. This study is designed to conduct the laboratory hydrofracturing test on the samples which are modeled after the drilling hole having the general drilling hole and spiral groove. And compare the initial fracturing pressure and fluid contact between them in order to the result of the hydrofracturing depending on the shape of the drilling hole. In addition, the results were compared with the numerical modeling values from 3DEC and they were also compared with the data from the advance researches. It was found from the study that rather than the contact area of the high pressures water, the force concentration depending on the form of guide hole was more effective in the hydrofracturing.

• The Journal of Korean Physical Therapy
• /
• v.5 no.1
• /
• pp.109-114
• /
• 1993

The originator of the proprioceptive neuromuscular facilitation method was Dr. Herman Kabat, a man who received the bachelor of science degree from New York University in 1932. In 1936 he moved to the University of Minnesota where he served as instructor in physiology and also studies medicine. He received his medical doctorate in 1942. When Dr. Karbat meet Sister Kenny suggested that certain change. She does not receptive his ideas. So that he decided to pursure the treatment of patients. Upon the establishment of the Karbat- kaiser Institute to be opened in 1946. Margaret Knott, the first physical therapist to be employed by him and to become his head physical therapist. In 1948 Vallejo center was opened. Dr. Kabat developed the PNF method combined motions to ascertain the effectiveness of maximal resistance and stretch in facilitating the response of a weak distal muscle. He identified mass movement patterns that were spiral and diagonal in character in 1965. Margaret Knott presented lecture at tile APTA Annual Conference in Las Vegas. The title was In the groove. On December 18, 1978 she passed away at her home in Vallejo. Marie-Louise Mangold is director of the Kaiser Foundation Rehabilitation Center now. She is the Vice President of International Proprioceptive Neuromuscular facilitation Association. About 20 physical therapist working teaching and study at KFRC in Vallejo. PNF neuromuscular mechanism becomes integrated and efficient without awareness of individual muscle action, reflex and a multitude of other neurophysiological reactions. The principles of PNF are visual consideration, verbal consideration, and proprioceptive input consideration with tactile stimulation, joint receptors, appropriate facilitation, stretch reflex normal timing, irradiation, pattern of movement.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.330-337
• /
• 2010

In this paper, 3-dimensional electromagnetic numerical analysis is performed about the eddy current(EC) array probe characteristic which is the next generation probe for accurate diagnosis of steam generator(SG) in nuclear power plants(NPPs). ASME(American Society of Mechanical Engineers) Standard and X-probe combo calibration standard tube are selected for acquisition of eddy current testing(ECT) signals and this result of compared with the real test signals for reasonability of result. Based on the analysis result of calibration standard tube, ECT signals that are about the defects of pitting, stress corrosion cracking(SCC), multiple SCC and wear is obtained. Material of specimen was Inconel 600 which is usually used for SG tubes in NPPs. The operation frequency of 300 kHz were used. The signal characteristics could be observed according to the various defects. The results in this paper can be helpful when the ECT signals from EC array probe are evaluated and analyzed.