• 한국유체기계학회 논문집
• /
• 제14권5호
• /
• pp.24-30
• /
• 2011

500W class MTG(Micro turbine generator) operating at 400,000 rpm is under development. From the cycle analysis, it is decided that the self-sustaining speed of MTG is 200,000rpm and the generating speed is 400,000 rpm. Therefore, motor should be designed so that it is able to rotate the rotor up to 200,000rpm and generator should designed so that it is able to generate 500W output at 400,000rpm. First step to design motor/generator is to determine the power and efficiency requirement. Not only the power into the compressor and from the turbine at the operating speed but also the mechanical and electrical losses should be considered in determining the power and efficiency requirement. This study presents the procedure and the results of determining the power and efficiency requirement considering the mechanical and electrical losses depending on the rotating speed which is measured from the experiment.

• 한국군사과학기술학회지
• /
• 제20권3호
• /
• pp.376-383
• /
• 2017

This paper describes the gyroscopic stability and the drag characteristics of the smart munition with a course correction fuze(CCF). A ballistic analysis was conducted to figure out the effect of the canards on the gyroscopic stability of the projectile. The analysis used the commercial ammunition performance evaluation software: Projectile Design and Analysis System(PRODAS). In particular, we compared the PRODAS analysis results to real field test results to investigate the influence of the CCF mounted projectile. In addition, some ballistic simulations were carried out to provide the conditions suitable for wind tunnel tests. Experimental results show that the added drag force by the canards is almost uniform regardless of the Mach number when the projectile is at the normal position where the angle of rotation and the angle of attack are both 0 degrees. However, as the angle of attack of the projectile increases, the additional drag force depends on the deflection of the canards.

• Journal of Magnetics
• /
• 제21권1호
• /
• pp.148-152
• /
• 2016

The main goal was to evaluate effectiveness of a modified TSE sequence compared with DIR (double inversion recovery) sequence in acquisition of fast flow brain vessel images using signal void effect. 32 healthy volunteers (10 men and 22 women; mean age of 31 years; ranging between 28-43 years) who underwent black blood DIR sequence (group A) and the modified TSE sequence (group B) were enrolled in our study. Signal to Noise Ratio (SNR) and Contrast to Noise Ratio (CNR) of the internal carotid arteries' lumen were compared in T1 and T2 weighted images for both group A and B. The images obtained from group B showed lower SNR values in internal carotid artery than the group A in both of the T1 and T2 weighted images (11.49% and 13.66% respectively). While the CNR values were higher in the group B than the group A in both of the T1 and T2 weighted images (8.69% and 7.55 % respectively). The qualitative score of all categories were not significantly different between the two groups. Furthermore approximately 49% of the total scan time was reduced from group B. Our study is to shorten the scanning time and minimize the inconveniences of the patients in acquisition of the black blood images of brain by using the signal void effect in the modified TSE technique while keeping the diagnostic value of the test.

• 소성∙가공
• /
• 제13권8호
• /
• pp.716-722
• /
• 2004

Effects of sliding speed, applied load, and thickness of PMMA (Poly Methyl Methacrylate) coating layers on their dry sliding frictional and wear behavior were investigated. Sliding wear tests were carried out using a pin-on-disk wear tester. The PMMA layer was coated on Si wafer by a spin coating process with two different thicknesses, $1.5\mu\textrm{m}$ and $0.8\mu\textrm{m}$. AISI 52100 bearing steel balls were used as a counterpart of the PMMA coating during the wear. Normal applied load and sliding speed were varied. Wear mechanisms of the coatings were investigated by examining worn surfaces using an SEM. Friction coefficient of the coatings decreased with the increase of the applied load. Both adhesion and deformation of the coating determined the coefficient. The thicker PMMA layer with the thickness of $1.5mutextrm{m}$ showed lower friction coefficient than the thinner layer under most test conditions. Effects of sliding speed and applied load on the frictional behavior were varied depending on the thickness of the coating layer.

• 천문학회보
• /
• 제39권1호
• /
• pp.52.1-52.1
• /
• 2014

Radio pulsars are highly magnetized, rapidly rotating neutron stars that emit synchrotron radiation along the magnetic axes at their spin frequencies. Traditionally, pulsar observations have been done at low frequencies (MHz up to a few GHz), since radio pulsar spectrum is known to a power-law with a steep negative spectral index. More recently, high-frequency pulsar observations (several GHz and above) have been made as a broadband spectrometer and fast computers became available. High-frequency pulsar observations will provide information on radio emission mechanism of pulsars in the vicinity of the neutron star surface. There is also huge interest from gravitational-wave and astrophysics community to find a pulsar in the center of our Galaxy. The Korean VLBI Network has three 21-m single dishes in the Korean peninsula. Using KVN's lowest observational frequency of 22-GHz, we performed test observations with the KVN targeting a few selected known, bright pulsars. In addition, we have been developing pulsar pipelines that can be utilized with a VLBI facility using Mark-V. We present a brief introduction of radio pulsars and show data obtained with the KVN.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.695-698
• /
• 2004

STSAT RWA (Reaction Wheel Assembly) micro-vibration is measured using KISTLER dynamic plate that can provide the time signals of three orthogonal forces and torques simultaneously up to 400Hz. In the post-processing, measured data are evaluated with respect to the wheel spin rate in both time and frequency domains, and the static/dynamic unbalances are evaluated from the extracted first harmonic component. Also the friction torque profile at each wheel speed is estimated from the measured data. Several higher order harmonic components are observed, that comes from its rotor shape as well as the wheel bearing characteristics. One of the most peculiar characteristics of this wheel is that the dynamic properties of two radial unbalance components are much different from each other as the RWA mounting configuration on a spacecraft is different from conventional RWA mounting configuration. Rocking mode is not appeared below 400Hz for all operating speed because the wheel size is very small. The post-processed results will be used for jitter analysis of STSAT due to RWA micro-vibration.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.692-697
• /
• 2005

좋은 날개 실속특성 및 실속/스핀의 특성이 입증된 선미익형 항공기를 현재 개발중에 있다. 전에 개발된 1호기 및 2호기 시제기는 코어 샌드위치 형식으로 날개 전체가 채워지고 고정식 착륙장치로 제작되었다. 새로이 개발될 반디호는 접개식 착륙장치와 날개와 동체에 일반적인 폼 코아 샌드위치층이 장착될 예정이다. 제작을 위해 시편 시험을 포함한 복합 소재 제작 공정이 연구되었고 적층 몰드를 이용하여 유리 섬유 천으로 폼 코어 위로 상온 적충하는 방식이 채택되었으며, 복합소재 부품들은 실온과 대기압하에 경화시킨다. 일반적으로, 몰드부품들은 양산에 적합한 매끄러운 표면 조도와 표준 품질을 보여주었다. 본 연구에서는 소형 항공기 반디호 몰드 기술과 개발 상황을 기술하였다.

• 한방재활의학과학회지
• /
• 제20권3호
• /
• pp.37-60
• /
• 2010

Objectives : The purpose of this study was to investigate the relationship between masseter and cervical muscle activity and temporomandibular disorder in female office workers. Methods : Experimental group of 24 healthy subjects complained of temporomandibular joint related to computer use which lasted more than 3 months in the past year and was present in the past 7 days as well as on the day of test. Control group of 20 healthy subjects had no complaints of minimal discomfort on the day of test, and had no discomfort in the past 7 days. If they had reported discomfort in the past 12 months, it was of a short duration(<3 months) and resolved at least 3 months prior to participation. Outcomes were assessed by meridian-electromyography(MEMG), whole spin x-ray, mandibular function impairment questionnaire(MFIQ), neck disability index(NDI), visual analog scale(VAS), Beck depression inventory(BDI), stress reaction inventory(SRI) and Holmes & Rahe social readjustment rating scale(SRRS). Results : The contraction power of masseter muscle, upper trapezius, sternocleido-mastoid muscle and erector spinae by MEMG was significantly higher in the experimental group. The muscle fatigue of masseter muscle and sternodeido-mastoid muscle by MEMG was significantly higher in the experimental group. SRI was significantly higher in experimental group. There was no significant difference between two groups in the Jackson's angle, Cobb's method and cranio-cervical posture. Conclusions : The results suggest that temporomandibular disorder related mental stress but physical stress does not change cervical structure significantly.

• 비파괴검사학회지
• /
• 제32권4호
• /
• pp.393-400
• /
• 2012

최근 나노 박막은 MEMS/NEMS, 광학 코팅, 반도체 산업 등 다양한 분야에서 사용이 되고 있다. 박막은 마모, 침식, 부식, 고온 산화를 방지하기 위한 목적으로 사용될 뿐 아니라 특성화된 자기, 유전적 특성을 만들기 위한 목적으로 사용된다. 많은 연구자들이 이러한 박막 구조의 특성(밀도, 입자 크기, 탄성 특성, 필름/기지 계면의 특성)을 평가하기 위하여 많은 연구를 진행하고 있다. 이들 중에 박막과 기지 사이의 접합 특성을 평가하는 것이 많은 연구자들의 주 관심사가 되어 왔다. 본 연구에서는 나노 박막의 접합 특성을 평가하기 위하여 각기 다른 접합 특성을 가지는 폴리머 박막 시험편을 제작하였다. 제작된 시험편의 접합 특성을 측정하기 위하여 초음파현미경의 V(z) 곡선법을 이용하여 표면파의 속도를 측정하였다. 또한 계면을 포함하는 시험편의 표면을 전파하는 표면파의 속도와 접합력의 상관관계를 확인하기 위해 나노 스크래치 시험을 적용하였다. 그 결과 초음파현미경을 이용하여 측정된 표면파의 속도와 나노스크래치 시험을 이용한 임계하중이 일치하는 경향성을 나타내었다. 결론적으로 초음파현미경의 V(z) 곡선법은 나노 스케일 박막 계면에서의 접합 상태를 평가할 수 있는 기법으로 그 가능성을 나타내었다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제27권4호
• /
• pp.17-21
• /
• 2004

최근 의학 영상 기술의 발전과 함께 동적 골반 MRI(Pelvic magnetic resonance imaging)가 소개되었고 이러한 기술을 이용하여 동적 MR 배변조영술이 소개되어 환자의 진단에 도움을 주기 위해 사용되고 있다. 처음에 도입 당시에는 탈장(Enterocele)과 방광탈출증(Cystocele) 등을 진단하기 위하여 사용되었지만, 이후 장기의 탈출증(Prolapse), 또는 다른 골반 장기의 이상에 점점 그 유용성이 증명되어 현재는 기능성변비 등 다른 질환에서도 많은 보고가 있다. 본 논고에서는 골반 MRI 및 동적 MR 배변조영술에 대해서 소개하고 앞으로의 임상적 응용에 대한 전망을 살펴보도록 한다. 최근까지도 Pelvic MRI의 결과들은 앙와위(Supine position)에서 골반의 움직임을 관찰하는데 Yang 등은 26명의 골반 기관의 탈출증(Pelvic organ prolapse)을 가진 환자들을 관찰하고 Pubococcygeal line을 해부학적인 지표로 이용하여 좋은 결과를 얻었다고 보고했다. 이들은 Fast gradient recalled acquisition(fast GRASS)을 이용하여, Cystocoele, Prolapse, Enterocoele 그리고 Rectocoele 등을 증상이 없는 대조군과 비교하여 보고하였다. Kruyt 등은 Posterior compartment를 주로 관찰하여 MRI가 Fluoroscopy에 비하여 더 도움이 된다고 보고하였다. Healy 등은 Fast GRASS sequence를 이용하여 변비를 가진 환자와 변실금을 가진 환자, 그리고 증상이 없는 대조군을 대상으로 하여 동적 MRI 검사를 실시하였다. 이들은 변비나 변실금 증상과 관련되어 환자들의 Posterior compartment에 여러 곳에서 Prolapse을 관찰할 수 있었다. 이후 MRI 기술은 Lienemann 등에 의해서 더욱 발전했는데 그는 Fast T2 weighted turbo spin echo 기술을 이용하여 영상을 좀더 세밀하게 얻을 수 있게 되었다. 지금까지의 앙와위에서의 검사로 진단에 한계가 있었던 Intussusception 등의 질환을 Open MR 등의 방법으로 극복할 수 있다면 장래에는 방사선학적 배변조영술을 대체할 수 있는 검사법으로 발전할 수 있을 것으로 생각된다.