• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.133-144
• /
• 2003

Horizontal consolidation characteristics of Busan marine clay were investigated by computing coefficient of horizontal consolidation from Piezocone data and comparing their results with those of standard consolidation test. It is well known that current prediction models of $c_h$ for high plastic soils have large uncertainties, and show a great difference between the predicted and the measured values. However, the spherical models and expanding cavity theory of Torstensson(1977), and Burns & Mayne(1998) based on modified Cam-Clay model with critical limit state concepts have relative reliability in estimating $c_h$ and good applicability in highly plasticity soils. In this paper, a normalization technique was used to evaluate $c_h$ using the Burns and Mayne's method based on the dissipation test, and their normalized consolidation curves give 0.015 of time factor($T_{50}$) when 50% degree of consolidation is completed. Comparison study using Piezocone data obtained at other similar ground site shows 1.5 times less systematicality than that of standard consolidation test, which indicates considerable approximation with the measured values because standard consolidation test gives the difference of three to few times compared with the measured values. In addition, design chart for estimating $c_h$ based on the chart from Robertson et al.(1992) and using the other method of the direct prediction from the of dissipation test was newly proposed. It is judged that new proposed chart is very applicable to Korean marine soils, especially in very high plastic soils.

• Progress in Medical Physics
• /
• v.26 no.1
• /
• pp.18-27
• /
• 2015

Since a Compton camera has high detection sensitivity due to electronic collimation and a good energy resolution, it is a potential imaging system for nuclear medicine. In this study, we investigated the feasibility of a Compton camera for multi-tracer imaging and proposed a rotating Compton camera to satisfy Orlov's condition for 3D imaging. Two software phantoms of 140 and 511 keV radiation sources were used for Monte-Carlo simulation and then the simulation data were reconstructed by listmode ordered subset expectation maximization to evaluate the capability of multi-tracer imaging in a Compton camera. And the Compton camera rotating around the object was proposed and tested with different rotation angle steps for improving the limited coverage of the fixed conventional Compton camera over the field-of-view in terms of histogram of angles in spherical coordinates. The simulation data showed the separate 140 and 511 keV images from simultaneous multi-tracer detection in both 2D and 3D imaging and the number of valid projection lines on the conical surfaces was inversely proportional to the decrease of rotation angle. Considering computation load and proper number of projection lines on the conical surface, the rotation angle of 30 degree was sufficient for 3D imaging of the Compton camera in terms of 26 min of computation time and 5 million of detected event number and the increased detection time can be solved with multiple Compton camera system. The Compton camera proposed in this study can be effective system for multi-tracer imaging and is a potential system for development of various disease diagnosis and therapy approaches.

• Applied Microscopy
• /
• v.35 no.2
• /
• pp.89-96
• /
• 2005

The ultrastructures of the fertilized egg envelope from Hyphessobrycon serpae belonging to Characidae was studied using scanning and transmission electron microscopes to get systematic fundamental data for classification of species and to confirm whether micropyle is a common trait of Characidae or not. The fertilized egg was of colorless, transparent, spherical, adhesive and demersal type. There were not oil droplets in vitelline membrane and attached structures in the outside of fertilize egg envelope. The egg envelope had a single micropyle resembling the pathway of sperm in the area of the animal pole. The micropyle was surrounded by 13 to 15 protruded lines of the egg envelope in a radiated form. The outer surface of fertilized egg envelope was covered by reticular adhesive fibrous structures and irregularly arranged by pore canals. The fertilized egg envelope consisted of three distinct layers an outer adhesive fibrous layer with high electron density, a middle layer with pore canals, and an inner layer consisting of 6 to 7 lamellae alternating layers with interlamellae of lower electron density. These ultrastructural characters of fertilized egg envelope form Hyphessobrycon serpae can be utilized in taxonomy of teleost, and as fundamental data for study on early development of fertilized egg. It seems that the morphology of micropyle is a common trait of Characidae

• Current Optics and Photonics
• /
• v.4 no.3
• /
• pp.174-185
• /
• 2020

Multiscattering occurs when a laser transmits into dense atmosphere targets (e.g. fogs, smoke or clouds), which can cause depolarization effects even though the scattering particles are spherical. In addition, multiscattering effects have additional information about microphysical properties of scatterers. Thus, multiscattering can be utilized to study the microphysical properties of the liquid water cloud. In this paper, a Monte Carlo method was used to simulate multi-scattering transmission properties of Lidar signals in the cloud. The results showed the slope of the degree of linear polarization (SLDLP) can be used to invert the extinction coefficient, and then the cloud effective size (CES) and the liquid water content (LWC) may be easily obtained by using the extinction coefficient and saturation of the degree of linear polarization (SADLP). Based on calculation results, a microphysical properties inversion method for a liquid cloud was presented. An innovative multiscattering polarization Lidar (MSPL) system was constructed to measure the LWC and CES of the liquid cloud, and a new method based on the polarization splitting ratio of the Polarization Beam Splitter (PBS) was developed to calibrate the polarization channels of MSPL. By analyzing the typical observation data of MSPL observation in the northern suburbs of Nanjing, China, the LWC and CES of the liquid water cloud were obtained. Comparisons between the results from the MSPL, MODIS and the Microwave radar data showed that, the microphysical properties of liquid cloud could be retrieved by combining our MSPL and the inversion method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.2D
• /
• pp.323-334
• /
• 2011

In this study, we performed the residual geoid modeling using the FFT and LSC methods in context of application of R-R (Remove and Restore) technique as a general technique for gravimetric geoid model in order to propose the effective way of geoid determination in Korea. For this, a number of data compiled for residual geoid modeling by the multi-band spherical FFT method with Stoke's formula and LSC method as known as statistical method. The geometric geoidal heights obtained from 503 GPS/Levelling data were used for inducing the various elements and proper computation process which should be considered for improving the accuracy of residual geoid modeling. Finally, we statistically compared the results of residual geoid heights between FFT and LSC methods and reviewed then the proper way of residual geoid modeling to the region of Korea. As the results of comparison, LSC method is not suitable for residual geoid modeling in Korea due to the noise and lack of gravity observations and the effects of local characteristics, while FFT method by applying Stokes' integral with proper cap size and modified kernel which provides the better accuracy of residual geoid heights up to 10 cm more than those of LSC method.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.103-113
• /
• 1998

Until now, the study of eye refractive error examination for high school students are a few report that in Korea. In particular, there is few report about the visual power for same group during several years. We compared the study of refractive error done this year with that reported three years ago at the same high school. From the these data, the distribution of ammetropia was investigated. The study of refractive error for high school students was also compared with those reported before for the Adults and the middle school student. When the visual power is refered to spherical equivalent, the 36% of the whole students examined above had emmetropia and the other part of them fumed out to be ammetropia which is classify to 60.6% belonged to myopia and 4.4% belonged to hyperpia. The ratio of myopia for this year students is increased in comparision with the students in 1995. The ratio of emmetropia for this year students is 7.4% higher, and the ratio of myopia for this year students is 4% higher, but the ratio of hyperopia is very lower than that for the adults in 1997. In the kind of refractive error, it is classified that a simple myopia is shown to highest ratio as a 28.6% of 1212 eyes examined, a compound myopic astigmatism to the next high ratio as a 22.4%, a simple myopic astigmatism as 14.4%, a simple hyperopic astigmatism as 3.1%, a mixed astigmatism as a 1.7%, a simple astigmatism as 1.2%, a compound hyperopic astigmatism as 1.2%, respectively. The percentage of an astigmatism is a 76.7% of total eyes examined if Cyl-0.25 Dptr is included to an astigmatism. On the other hand, The percentage of an astigmatism is a 45.6% of total eyes examined if Cyl-0.25 Dptr is excluded to an astigmatism. In the kind of astigmatism, the number of students had an astigmatism with the rule is about 4.5 times than that of astigmatism against the rule. From the result of comparision the right eye with the left eye, the right eye of the students had more a myopic refractive error than the left eye, which is same as adults' case, there is no difference in a refractive error between the boy students and the girl students.

• Progress in Medical Physics
• /
• v.27 no.2
• /
• pp.86-92
• /
• 2016

An absorbed dose calculation method using a digital phantom is implemented in normal organs. This method cannot be employed for calculating the absorbed dose of tumor. In this study, we measure the S-value for calculating the absorbed dose of each organ and tumor. We inject a radioisotope into a torso phantom and perform Monte Carlo simulation based on the CT data. The torso phantom has lung, liver, spinal, cylinder, and tumor simulated using a spherical phantom. The radioactivity of the actual absorbed dose is measured using the injected dose of the radioisotope, which is Cu-64 73.85 MBq, and detected using a glass dosimeter in the torso phantom. To perform the Monte Carlo simulation, the information on each organ and tumor acquired using the PET/CT and CT data provides anatomical information. The anatomical information is offered above mean value and manually segmented for each organ and tumor. The residence time of the radioisotope in each organ and tumor is calculated using the time activity curve of Cu-64 radioactivity. The S-values of each organ and tumor are calculated based on the Monte Carlo simulation data using the spatial coordinate, voxel size, and density information. The absorbed dose is evaluated using that obtained through the Monte Carlo simulation and the S-value and the residence time in each organ and tumor. The absorbed dose in liver, tumor1, and tumor2 is 4.52E-02, 4.61E-02, and 5.98E-02 mGy/MBq, respectively. The difference in the absorbed dose measured using the glass dosimeter and that obtained through the Monte Carlo simulation data is within 12.3%. The result of this study is that the absorbed dose obtained using an image can evaluate each difference region and size of a region of interest.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.1
• /
• pp.66-76
• /
• 2016

Determination of type of a vehicle is being used in various areas such as collecting tolls, collecting statistical traffic data and traffic prognosis. Because most of the vehicle type classification systems depend on vehicle length indirectly or directly, highly reliable automatic vehicle length measurement system is crucial for them. This study makes use of a pencil beam laser rangemeter and devises a mechanical device which rotates the laser rangemeter. The implemented system measures the range between a point and the laser rangemeter then indicates it as a spherical coordinate. We obtain several silhouettes of cross section of the vehicle, the rate of change of the silhouettes, signs of the rates then squares the rates to apply cell averaging constant false alarm rate (CA-CFAR) technique to find out where the border is between the vehicle and the background. Using the border and trigonometry, we calculated the length of the vehicle and confirmed that the calculated vehicle length is about 94% of actual length.

• Journal of Information Display
• /
• v.12 no.3
• /
• pp.145-152
• /
• 2011

Since the discovery of fullerenes as a class of nanostructure compounds, many potential applications have been suggested for their unusual structures and properties. The isolated pentagon rule (IPR) states that all pentagonal carbon rings are isolated in the most stable fullerene. Fullerenes $C_n$ are a class of spherical carbon allotrope group with unique properties. Electron transfer between fullerenes and other molecules is thought to involve the transfer of electrons between the molecules surrounding the fullerene cage. One class of electron transfer molecules is the methanofullerene derivatives ([6,6]-phenyl $C_{61}$-butyric acid methyl ester (PCBM), 4-(2-ethylhexyloxy)-[6,6]-phenyl $C_{61}$-butyric acid methyl ester (p-EHO-PCBM), and 4-(2-ethylhexyloxy)-[6,6]-phenyl $C_{61}$-butyric acid (p-EHO-PCBA), 10-12). It has been determined that $C_{60}$ does not obey IPR. Supramolecular complexes 1-9 and 10-12 are shown to possess a previously unreported host.guest interaction for electron transfer processes. The unsaturated, cis-geometry, thiocrown ethers, (1-9) (described as [X-UT-Y], where X and Y indicate the numbers of carbon and sulfur atoms, respectively), are a group of crown ethers that display interesting physiochemical properties in the light of their conformational restriction compared with a corresponding saturated system, as well as the sizes of their cavities. Topological indices have been successfully used to construct mathematical methods that relate structural data to various chemical and physical properties. To establish a good relationship between the structures of 1-9 with 10-12, a new index is introduced, ${\mu}_{cs}$. This index is the ratio of the sum of the number of carbon atoms ($n_c$) and the number of sulfur atoms ($n_s$) to the product of these two numbers for 1-9. In this study, the relationships between this index and oxidation potential ($^{ox}E_1$) of 1-9, as well as the first to third free energies of electron transfer (${\Delta}G_{et(n)}$, for n = 1-3, which is given by the Rehm-Weller equation) between 1-9 and PCBM, p-EHO-PCBM, and p-EHO-PCBA (10-12) as [X-UT-Y]@R(where R is the adduct PCBM, p-EHO-PCBM, and p-EHO-PCBA group) (13-15) supramolecular complexes are presented and investigated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.9
• /
• pp.667-674
• /
• 2014

A ship's propulsion shafting system is subjected to varying magnitudes of intermittent loadings that pose great risks such as failure. Consequently, the dynamic characteristic of a propulsion shafting system must be designed to withstand the resonance that occurs during operation. This resonance results from hydrodynamic interaction between the propeller and fluid. For ice-class vessels, this interaction takes place between the propeller and ice. Producing load- and resonance-induced stresses, the propeller-ice interaction is the primary source of excitation, making it a major focus in the design requirements of propulsion shafting systems. This paper examines the transient torsional vibration response of the propulsion shafting system of an ice-class research vessel. The propulsion train is composed of an electric motor, flexible coupling, spherical gears, and a propeller configuration. In this paper, the theoretical analysis of transient torsional vibration and propeller-ice interaction loading is first discussed, followed by an explanation of the actual transient torsional vibration measurements. Measurement data for the analysis were compared with an applied estimation factor for the propulsion shafting design torque limit, and they were evaluated using an existing international standard. Addressing the transient torsional vibration of a propulsion shafting system with an electric motor, this paper also illustrates the influence of flexible coupling stiffness design on resulting resonance. Lastly, the paper concludes with a proposal to further study the existence of negative torque on a gear train and its overall effect on propulsion shafting systems.