• 융복합기술연구소 논문집
• /
• 제3권1호
• /
• pp.45-49
• /
• 2013

Spherical active carbon materials have been used for the removal of pollutants in the area of food processing, water treatment, air purification, oral administration. Moreover, they are now expected to make an epoch in the areas of electronics, life science, environmental technology, and so on due to their superior physical properties. Carbon particles should be requested for the edgeless spherical shapes in order to minimize the loss due to the abrasion during the process and/or practical use, but the carbon particles manufactured from petroleum-based pitch do not meet these needs. Nowadays, thus, the spherical active carbon particles carbonized from various spherical polymer beads are studied with thermoplastic and/or thermosetting polymers. In this paper, the synthesis of spherical phenolic beads and furan beads, which are thermosetting polymers, and their carbonization techniques are examined.

• 한국세라믹학회지
• /
• 제53권1호
• /
• pp.68-74
• /
• 2016

In this study, the fabrication of zeolite combined activated carbon spherical samples was carried out as follows. Briefly, ZSM-5 zeolite and activated carbon were composed as main absorbent materials; by controlling the weight percentage of zeolite and binder materials, a series of spherical samples (AZP 4, 6, 8) were prepared. These spherical samples were characterized by BET, XRD, SEM, EDX, and pressure drop; benzene and iodine adsorption tests, bactericidal effect test, and ignition temperature test were also performed. The adsorption capability was found to depend on the BET surface area; the spherical samples AZP6 with high BET surface area of $1011m^2/g$ not only exhibited excellent removal effects for benzene (24.9%) and iodine (920mg/g) but also a good bactericidal effect. The enhanced ignition temperature may be attributed to the homogeneous dispersion conditions and the proper weight percentage ratio between zeolite and activated carbon.

• 융복합기술연구소 논문집
• /
• 제12권1호
• /
• pp.13-18
• /
• 2022

Polyacrylonitrile was synthesized through suspension polymerization and then sieved to obtain spherical beads with a size of 200~510 ㎛. PAN was copolymerized with 2 mol% MMA monomer which is known to promote cyclization and crosslinking of nitrile group. The resonance cyclization reaction of the nitrile group in the synthesized PAN beads was observed near 170℃ with thermal analysis and FT-IR. The reaction conversion of the nitrile group in spherical beads was 23% during heat treatment, which was lower than that of the well-oriented PAN fiber used as a precursor of carbon fiber. This is because the stereo-regularity of molecular chains in the form of a random coil (spherical bead) is much lower than that of PAN fiber. It was confirmed that the compressive strength of the spherical PAN bead was greatly improved through the resonance cyclization and shrinkage according to the heat treatment, and it was also observed that the pores in PAN beads were formed after the heat treatment.

• 한국세라믹학회지
• /
• 제46권6호
• /
• pp.568-573
• /
• 2009

In this study, we used coal based activated carbons as starting material and phenolic resin (PR) as a bonding agent to prepare spherical shaped activated carbons. The textural properties of SAC were characterized by BET surface area, XRD, SEM, iodine adsorption, strength intensity and pressure drop. According to the results, the spherical activated carbon prepared with activated carbon and PR at a ratio of 60:40 was found to have the best formation of spherical shape, which was found in sample SAC40. After activation, SAC40 has high BET surface area, iodine adsorption capability and strength value, and lowest pressure drop.

• Carbon letters
• /
• 제11권4호
• /
• pp.304-310
• /
• 2010

To manufacture a carbon/carbon composite the coal tar pitch was used as the matrix precursor and the PAN (polyacrylonitrile)-based carbon fiber was used as the reinforcing material to weave 3-directional preform. For pressure carbonization HIP equipment was used to produce a maximum temperature of $1000^{\circ}C$ and a maximum pressure of 100 MPa. The carbonization was induced by altering the dwell temperature between $250^{\circ}C$ and $420^{\circ}C$, which is an ideal temperature for the moderate growth of the mesophase nucleus that forms within the molten pitch during the pressure carbonization process. The application of high pressure during the carbonization process inhibits the mesophase growth and leads to the formation of spherical carbon particles that are approximately 30 nm in size. Most particles were spherical, but some particles were irregularly shaped. The spread of the carbon particles was larger on the surface of the carbon fiber than in the interior of the matrix pocket.

• 한국재료학회지
• /
• 제20권10호
• /
• pp.535-542
• /
• 2010

In this study, we used coal-based activated carbons and charcoal as startingmaterials, phenolic resin (PR) as a binder, and TOS as a titanium source to prepare $TiO_2$ combining spherical shaped activated carbon photocatalysts. The textural properties of the activated carbon photocatalysts (SACP) were characterized by specific surface area (BET), energy dispersive X-ray spectroscopy (XRD), scanning electron microscopy (SEM), iodine adsorption, strength intensity, and pressure drop. The photocatalytic activities of the SACPs were characterized by degradation of the organic dyes Methylene Blue (MB), Methylene Orange (MO), and Rhodamine B (Rh. B) and a chemical oxygen demand (COD) experiment. The surface properties are shown by SEM. The XRD patterns of the composites showed that the SACP composite contained a typical single, clear anatase phase. The EDX spectro for the elemental indentification showed the presence of C and O with Ti peaks. According to the results, the spherical activated carbon photocatalysts sample of AOP prepared with activated carbon formed the best spherical shape, a high BET surface area, iodine adsorption capability and strength value, and the lowest pressure drop, and the photocatalytic activity was better than samples prepared with charcoal. We compared the degradation effects among three kinds of dyes. MB solution degraded with the SACP is better than any other dye solutions.

• 한국재료학회지
• /
• 제26권12호
• /
• pp.726-732
• /
• 2016

In this study, we used activated carbon(AC) as a carbon source, along with zeolite, to prepare spherical carbons using sucrose, starch and phenolic resin(PR) as binder material. The physicochemical characteristics of the three samples(AZ4P, AZ6P and AZ8P) were examined by BET, XRD, SEM, EDX, $H_2S/NH_3$ gas adsorption, compressive strength and ignition test techniques. Through comparative analysis of the compressive strength and ignition test results the AZ8P sample was found to have the best hardness and the highest temperature resistance capacity. After activation, the AZ8P sample had the best $H_2S$ adsorption capacity, and AZ6P was the most suitable for the adsorption of ammonia.

• Steel and Composite Structures
• /
• 제46권1호
• /
• pp.133-141
• /
• 2023

Based on the third-order shear deformation theory, the wave propagations in doubly curved spherical- and cylindrical- panels reinforced by carbon nanotubes (CNTs) are firstly investigated in present work. The coupled equations of wave propagation for the carbon nanotubes reinforced composite (CNTRC) doubly curved panels are established. Then, combined with the harmonic balance method, the eigenvalue technique is adopted to simulate the velocity-wave number curves of the CNTRC doubly curved panels. In the end, numerical results are showed to discuss the effects of the impact of key parameters including the volume fraction, different shell types (including spherical (R₁=R₂=R) and cylindrical (R₁=R, R₂=→∞)), wave number as well as modal number on the sensitivity of elastic waves propagating in CNTRC doubly curved shells.

• 공업화학
• /
• 제20권4호
• /
• pp.396-401
• /
• 2009

전기이중층 캐패시터의 성능향상을 위한 전극물질로서 resorcinol-formaldehyde수지를 탄소원으로 사용하여 meso-pore 비율 52~64%의 기공특성을 지니며 직경 $2{\sim}10{\mu}m$의 미세구형 활성탄을 제조하였다. 이 활성탄을 전기이중층에 적용한 결과, meso-pore구조의 미세구형활성탄은 전하전달저항의 저감 및 충방전율 수용능력 향상에 효과적인 영향을 나타내어 전기이중층 캐패시터의 성능향상을 위한 효과적인 전극물질이 될 수 있음을 확인할 수 있었다.

• Composites Research
• /
• 제21권4호
• /
• pp.15-21
• /
• 2008

단일 탄소섬유에 부착된 반구형 미소본드 시험편을 제사하여 에폭시수지와 난소섬유사이의 계면전단강도를 평가하였다. 반구형 미소시험편의 경우, 드랍레트 미소접합시험편 및 역반구형 미소접합시험편과 비교하여 계면강도측정값들이 높은 회귀계수 및 삭은 편차를 보여주었다. 이는반구형 시험편의 메니스커스 부분이 다른 미소시험편보다 작으며 핀홀 부하장치의 선단과 접촉하고 있는 수지부분에서 응력집중이 감소했기 때인 것으로 사료된다. 이들 시험에 대한 유한요소해석결과, 반구형시험편에서는 수지/섬유의 계면부를 따라 전단응력분포가 응력모드의 전환이 없이 안정하였다. 또한 이들 계면강도 측정데이터는 미소 바이스의 선단과 핀홀 판의 선단과 같은 부하장치의 종류에 따라 달라졌음을 알았다.