• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1093-1098
• /
• 2001

The interior sound pressure level of the Korean high speed train is predicted using ray acoustic method. The motor car, motorized car and passenger cabin are investigated under the environment of passing open countryside and inside tunnel Calculated sound levels of KHST are compared with the those of KTX prototype which vehicle shows similar acoustic behavior with KHST for the purpose of assuring the calculated data. In order to reduce the calculated SPL in systematic way, contribution analysis of sound sources and sensitivity analysis of concerning wall's transmission loss on the SPL of the designated receiving points are carried out. Finally, practical design suggestions are proposed.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.267-274
• /
• 2009

To predict efficiency of Interior Permanent Magnet Synchronous Motors(IPMSM) and to cope with the demagnetization risk of permanent magnets used in the IPMSM, accurate iron analysis of the IPMSM is very important at the motor design stage. In the analysis, we calculate the operation condition such as rotor speed and current angle. and then, we analyzed the iron loss of the machine for electric vehicle according to its driving condition. From the analysis results, it was shown that the harmonic iron losses of stator are larger than before at field-weakening region. In addition, it was revealed that rotor iron loss mainly induced by stator slot-ripples is independent of current angle and only varied according to the speed.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.2
• /
• pp.201-210
• /
• 2009

A loss minimizing controller is developed for a fuel cell electric vehicle (FCEV) permanent magnet synchronous motor (PMSM). The PMSM losses are modeled by some experimental equations. Applying Lagrangian to the loss function, a necessary condition for the optimality appears to be a fourth order polynomial, and the loss minimizing solutions are obtained by a simple numerical approach. On the other hand, the loss minimizing solutions are found by scanning the motor loss in the entire operating region. The two results agree well. The loss minimizing current sets for given torque and speed are made into a table, which is utilized as a look-up in the current control loop.

• Journal of the Korean Society of Safety
• /
• v.15 no.4
• /
• pp.56-61
• /
• 2000

The precise and reliable loss model for induction motor and converter system is very important in order to predict the efficiency performance of variable speed drives. This paper proposes an accurate loss model of induction motor and converter system. The motor losses, such as stator and rotor copper loss, core loss and stray loss, are considered for fundamental and harmonic frequencies. Also considered are the skin effect on rotor resistance, temperature effect on bath stator and rotor resistance, magnetizing inductance saturation, and friction and windage loss. All the above features are incorporated in a synchronous frame dynamic d-q equivalent circuit. The converter system, consisting of a diode rectifier and PWM transistor inverter, is modeled accurately for conduction and switching losses. Validity of the models, in both steady state and transient conditions, is verified by simulations.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.268-275
• /
• 2013

This paper shows the characteristics of performance for interior permanent magnet machine (IPM) considering driving conditions such as maximum torque per ampere (MTPA) and flux-weakening control especially in terms of harmonic loss. In particular, based on finite element analysis (FEA), permanent magnet (PM) eddycurrent loss and the harmonic iron loss have been computed where the models have been intentionally designed to identify the effects of pole-slot combinations on the loss while maintaining the required power for electric vehicle. From the analysis results, it was shown that the rotor iron loss and PM eddy-current loss of machine employing fractional slot winding are extremely large at load condition. Furthermore, it was revealed that the harmonic iron loss at high-speed operation is mainly distributed over stator teeth and rotor surface, which may aggravate cooling system of the rotor structure in the vehicle.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.2
• /
• pp.116-122
• /
• 2000

In the high speed range for salient type synchronous reluctance motor, the effect of iron loss can not be negligible. We have investigated the voltage equations including iron loss from the model that is added the equivalent iron loss in the equivalent inductance in series. In this paper, we derive Ld linear approximate equation from saturation range of Ld, Lq vs applied voltage characteristics and obtain equations including saturation and iron loss related to maximum torque control using Ld. The effect of saturation and iron loss is investigated under maximum torque control. And we show that the proposed maximum torque control scheme achieves the desired performances through experimental results.

• Journal of Korea Multimedia Society
• /
• v.16 no.9
• /
• pp.1067-1076
• /
• 2013

Known as an important criterion that evaluates performance of future high-speed backbone networks, burst data loss ratio is well-studied in Optical Burst Switching networks. Current literatures mostly focus on reduce burst loss ratio without considering the system stability and link utilization after reducing. In this paper, we propose a novel framework which comes from feedback theoretic to dynamically control burst loss ratio in OBS. The proposed scheme tries to track the pre-set values of burst loss ratio and increases the stability and link utilization degree. The simulation results show that measured burst loss ratio always tracks setup reference with small errors, wavelength channel utilization is increased up to 2% and the system stability is also improved.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.2
• /
• pp.149-153
• /
• 2000

Recently, some works to consider the influences of iron loss have been made in vector control of induction m motor. This paper investigates the effects of iron loss in stator flux-oriented system, and presents the control a algorithm to consider iron loss. The iron loss is modeled by equivalent iron loss resistance in parallel to m magnetizing inductance. The proposed method is verified by simulation and experimental results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.6
• /
• pp.2985-2991
• /
• 2013

Train radio system has been constructed in the second stage of Kyung-bu high speed railway adopting TETRA(Terrestial trunk radio) standard at 851MHz frequency band. The base stations of the train radio system should be located along railway track to ensure seamless communication between train and wayside taking the path loss of train radio propagation into consideration. This paper provides a quantitative analysis of the path loss characteristics based on the measurement results of the train radio propagation along the high speed railway. The free space propagation model and Okumura-Hata model are generally used for base station design, but they predicted 10dB lower or 20dB higher than the measured path loss. Linear regression of the field measured data by applying the log-distance model shows path loss exponent is in the 2.8-3.2 range, which can be used to predict the path loss of the train radio propagation.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.4
• /
• pp.549-555
• /
• 2023

Jacking force loss management inside the PSC Box girder of a common high-speed railway is a very important feature in girder performance, and requires detailed management during the maintenance of the girder. This study aimed to analyze the timing of re-tension prediction of PSC Box girder based on the reduction level of the packing force inside the girder and the results of the tension loss measured without the train load test. As a result of predicting the timing of re-tension according to the level of tension reduction of the PSC Box Girder, the Jacking Force Loss curve was gently analyzed before the structure reached 17 years after confirmed completion, and 17 years later, it was found that the jacking force loss curve progressed rapidly. The results confirmed that the tension of the structure decreases with the service life increase, but considerably decreases as the structure ages. Therefore, more data and research on tension loss of facilities over 20 years are much required.