• Journal of Korean Society of Transportation
• /
• v.14 no.4
• /
• pp.107-129
• /
• 1996

Recently, surveillance system designed to collect various trsffic information are becoming new areas of development . Among these, the image detector is a ayatem which can measure the travel time and speed in realtime and this is emerging as the most effcient tool to be available in future related areas. But in measuring wide-area information in realtime, the image detector are yet full of problem in its accuracy. The aim of this ahesis is to develop an algorithms which can collect wide-area information such as travel time and travel speed in urban networks and freeways in realtime. The information on wide-area such as travel time and travel speed is important in accomplishing strategic function in traffic control. The algorithm developed from this study is based on the image tracking model which tracks a moving vehicle form image datas collected continuously, and is constructed to perform realtime measurement. To evaluate the performance of the developed algorithms, 600 ind vidual vehicles in total were used as data for the study, and this evaluation was carried out with the differenciation of day and night condition at the access roads in front of AJou University, In the statistical analysis results, the error rate was recorded as 5.69% and it has proved to be applicable on the field in both day and noght conditions.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.201-210
• /
• 2018

This paper proposes a new start-up method for a load commutated inverter (LCI) in a large synchronous gas-turbine generator. The initial rotor position for start-up torque is detected by the proposed initial angle detector, which consists of an integrator and a phase-locked loop. The initial rotor position is accurately detected within 150ms, and the angle difference between the real position and the detected position is less than 1%. The LCI system operates in two modes (forced commutation mode and natural commutation mode) according to operating speed range. The proposed controllers include a forced commutation controller for the low-speed range, a PI speed controller and a PI current controller, where the forced commutation controller is connected to the current controller in parallel. The current controller is modeled by Matlab/Simulink, where a six-pulse delay of the thyristor and a processing delay are considered by using a zero-order hold. The performance of the proposed start-up method is evaluated in Matlab/Psim at standstill and at low speed. To verify the feasibility of the method, a 5kVA LCI system prototype is implemented, and the proposed initial angle detector and the system performance are confirmed by experimental results from standstill to 900rpm.

• Journal of Advanced Navigation Technology
• /
• v.7 no.2
• /
• pp.108-117
• /
• 2003

In this paper, two types of radar vehicle detectors compatible with currently being used ILD(Inductive Loop Detector) without any modification has been developed. With these vehicle detectors based on FMCW altimeter and Doppler speedometer techniques at 24 GHz, the length and speed of a vehicle can be detected. For signal processing part, we have used DAQ board and programmed with LabView. For compatibility with traffic information network connected with existing ILD's, traffic information has been sent to VDS by using RS-232C standard interface. This development has improved approximately 10% in accuracy in terms of the speed and length information compared with that of the installed ILD in the test field.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.209-212
• /
• 2001

A flame detector responds either to radiant energy visible to the human eye or outside the range of human vision. Such a detector is sensitive to glowing embers, coals, or flames which radiate energy of sufficient intensity and spectral quality to actuate the alarm. An infra-red detectors can respond to the total IR component of the flame alone or in combination with flame flicker in the frequency range of 5 to 30 Hz. A major problem in the use of infrared detectors receiving total IR radiation is the possible interference of solar radiation in the infrared region. When detectors are located in places shielded from the sun, such as vaults, filtering or shielding the unit from the sun's rays is unnecessary. In this study, we proposed method for redue a false alarm with using filtering & sensor technology for distinguish of causes of raise a false alarm and pure flame.

• ETRI Journal
• /
• v.34 no.2
• /
• pp.175-183
• /
• 2012

Conventional synchronization algorithms for impulse radio require high-speed sampling and a precise local clock. Here, a phase-locked loop (PLL) scheme is introduced to acquire and track periodical impulses. The proposed impulse PLL (iPLL) is analyzed under an ideal Gaussian noise channel and multipath environment. The timing synchronization can be recovered directly from the locked frequency and phase. To make full use of the high harmonics of the received impulses efficiently in synchronization, the switching phase detector is applied in iPLL. It is capable of obtaining higher loop gain without a rise in timing errors. In different environments, simulations verify our analysis and show about one-tenth of the root mean square errors of conventional impulse synchronizations. The developed iPLL prototype applied in a high-speed ultra-wideband transceiver shows its feasibility, low complexity, and high precision.

• Journal of Mechanical Science and Technology
• /
• v.19 no.12
• /
• pp.2197-2204
• /
• 2005

The combination of Gas chromatography (GC) for separation and Flame Ionization Detection (FID) for detection and identification of the components of a mixture of compounds is a fast and strongly proved method of analytic chemistry. The objective of this research was to design a combined High-speed miniature screening Gas chromatograph along with a Flame Ionization Detector for quick, quantitative and qualitative analysis of gas components. This combined GC-FID system is suitable to detect the volatile and semi-volatile hydrocarbons present in a gas mixture. The construction made it less expensive, easy to use and movable. The complete gas path was developed. On/off valves, temperature and flow sensors and their interface electronics were used for controlling purpose. A Microcontroller was programmed to measure the temperature and gas flow using the sensors and to control and regulate them using the electronics and valves. A pocket PC with its touch screen served as a user interface for the system. Software was developed for the pocket PC, which makes the communication possible with the Microcontroller. The system parameters can be indicated in the Pocket PC as simple text and also the analysis result can be displayed.

• Journal of the Korean Society of Safety
• /
• v.32 no.4
• /
• pp.114-121
• /
• 2017

In order to overcome the limitations of the mobile speed system for 1 lane, this study is used a multi-laser beam to develop a mobile speed measuring system, using a multi-phase beam. By using multi-laser beam, least squares algorithms and speed error processing algorithms were developed to improve speed accordancy and speed error rates compared to conventional mobile speed meters using a single laser beam. A field test showed that 80.0 percent of 3 lane and 87.0 percent of 4 lane were appropriate for the mobile speed system. With the development of the mobile speed measuring system, it is expected to dramatically reduce the accidents caused by the speed of traffic. It is also expected to effectively operate equipment and manage the cost by improving manpower and providing improved enforcement accuracy, by contributing positively to public institution and public affairs.

• Journal of Korean Society of Transportation
• /
• v.24 no.2 s.88
• /
• pp.19-30
• /
• 2006

This study deals with the optimized detector location considering the traffic characteristics in National Highway. Although there ave many construction works for ITS in National Highway, there is not specific criteria for detector location which can effect the accuracy of traffic information. This study. therefore. aims to Provide the optimized detector location criteria which can represent the traffic characteristics of National Highway. It collects traffic factors of study area by GPS Probe-car and defector, and Presents the optimized detector location by the correlation analysis between spot-speed and link-travel-time. The main results of this study are as followings ; First, the correlation between the spot-speed and link-travel-time Presents the opposite bell shape of the graph (U-type owe) which is increased it?on the upstream then, declined through some unspecified Point of the link. Second, the optimized detector location usually distributes around midstream of link, even though it does not have a consistency. Third, therefore, the optimized detector location generally should be located between $55{\sim}60%$ of total link length. Forth. high level of vertical slope is one of the most important factors of detector location, so it should be excluded for determination of optimized detector location. Finally, expecting that the results of this study would improve the accuracy of travel time estimation and forecasting.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1239-1241
• /
• 2001

This research addresses a new vehicle detecting scheme which uses MR(Megneto Resistive) sensor. A vehicle detector which includes two MR sensors for detecting car presence and speed, sensor voltage amplifiers, signal processor, microprocessor, RF data transceiver and a simple car moving simulator is constructed. From experimental results with the vehicle detector the proposed vehicle detecting scheme was verified.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.79.3-79
• /
• 2002

$\textbullet$ Introduction $\textbullet$ Structure of variable multi-valued spatial filter detector(VMSFD) $\textbullet$ Moment analysis by VMSFD $\textbullet$ Experimental results $\textbullet$ Fabricated chip with photodiode array $\textbullet$ Conclusion