• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.7
• /
• pp.911-917
• /
• 1999

The sonic nozzle is widely used as reference device for calibrating flowmeters In gas flow measurement and its use requires the Critical Flow Factor(CFF) based on the thermodynamic properties of the gas at the nozzle throat. ISO-9300 provides the calculating method of the factor. But since the CFF from this method show an error over ${\pm}0.5%$ In specific conditions and of ${\pm}0.1{\sim}{\pm}0.2%$ in common Natural Gas(NG) custody transfer condition. this method cannot be applied for gas flow measurement with sonic nozzle. Each research bodies or organizations of the world have joined in order to calculate the CFF more accurately. They have performed these works using their own method and compared the results with each other under the management of ISO. KOGAS have joined those works, because the high-pressure natural gas flow calibration facility of KOGAS will be constructed in late 1999, and then had necessities to calculate a CFF accurately. The calculation method of KOGAS was using the equation of state from AGA-8('94), high accuracy model of ideal gas properties and the solutions of thermodynamic equations. The evaluation results have had a very good consistency within ${\pm}0.05%$ in most NO custody transfer conditions compared to the speed of sound for methane and also shown that the CFF was within ${\pm}0.1%$ compared to the results of other works of the world.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.6
• /
• pp.26-36
• /
• 2020

The use of existing macroscopic research of pedestrian behavior on the walking link as data is limited in determining an individual pedestrian's moving route and the level of service. In macroscopic studies, it is difficult to make quantitative indices, such as pedestrian flow rate, occupied space, density, and speed for determining the level of service on pedestrian roads. Therefore, the microscopic pedestrian route is required to establish appropriate pedestrian policies. In this study, the Yeok-Sam subway station network was examined using a micro-simulation VISSIM, which was then calibrated and validated statistically. The Pedestrian Road's Level of Service of Yeok-Sam subway station area was evaluated using the pedestrian speed as the evaluating index on the Korean highway capacity handbook.

• Journal of the Society of Disaster Information
• /
• v.19 no.1
• /
• pp.184-194
• /
• 2023

Purpose: The purpose of this study is to identify the characteristics of C02 emissions by road before establishing a policy to reduce greenhouse gas emissions. Method: As for the analysis method, the traffic volume and speed of the road were estimated using the traffic Assignment model targeting 27 arterial road axes in Incheon Metropolitan City. And, after estimating CO2 emissions by road axis by applying this, the characteristics of each group were analyzed through cluster analysis. Result: As a result of cluster analysis using total CO2 emissions, CO2 emissions by truck vehicles, and the ratio of truck vehicle emissions to total carbon dioxide emissions, four clusters were classified. When examining the characteristics of each road included in each group, it was analyzed that the characteristics of each group appeared according to the level of impact by CO2 emissions and truck vehicles. Conclusion: It is judged that it is necessary to establish a plan in consideration of CO2 emission characteristics for road CO2 management for greenhouse gas reduction.

• Wind and Structures
• /
• v.6 no.6
• /
• pp.485-498
• /
• 2003

This paper presents a mechanical model of Rain-Wind Induced Vibration (RWIV) of stay cables. It is based on the physical interpretation of the phenomenon as given in Cosentino, et al. (2003, referred as Part I). The model takes into account all the main forces acting on cable, on the upper water rivulet (responsible of the excitation) and the cable-rivulet interaction. It is a simplified (cable cross-sectional and deterministic) representation of the actual (stochastic and three-dimensional) phenomenon. The cable is represented by its cross section and it is subjected to mechanical and aerodynamic (considering the rivulet influence) forces. The rivulet is supposed to oscillate along the cable circumference and it is subjected to inertial and gravity forces, pressure gradients and air-water-cable frictions. The model parameters are calibrated by fitting with experimental results. In order to validate the proposed model and its physical basis, different conditions (wind speed and direction, cable frequency, etc.) have been numerically investigated. The results, which are in very good agreement with the RWIV field observations, confirm the validity of the method and its engineering applicability (to evaluate the RWIV sensitivity of new stays or to retrofit the existing ones). Nevertheless, the practical use of the model probably requires a more accurate calibration of some parameters through new and specifically oriented wind tunnel tests.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.219-230
• /
• 1995

The flow characteristics of a two-dimensional offset jet issuing parallel to a rough wall is experimentally investigated by using a split film probe with the modified Stock's calibration method. The mean velocity and turbulent stresses profiles in the up and down-stream locations of the wall-attachment regions are measured and compared with those of the smooth wall attaching offset jet cases. It is found that the wall-attachment region on the rough wall is wider than on the smooth wall for the same offset height and the jet speed. The position of the maximum velocity point is farther away from the wall than that for the smooth wall case because of the thick wall boundary layer established by the surface roughness. It is concluded that the roughness of the wall accelerates the relaxation process to a redeveloped plane wall jet and produces a quite different turbulent diffusion behavior especially near the wall from comparing with the smooth plane wall jet turbulence.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.80-89
• /
• 1998

The residual gas in an spark-ignition engine is one of important factors on emissions and performance such as combustion stability. With high residual gas fractions, flame speed and maximum combustion temperature are decreased and these are deeply related with combustion stability especially at idle and NOx emission at relatively high engine load. Therefore, there is a need to characterize the residual gas fraction as a function of the engine operating load. Therefore, there is a need to characterize the residual gas fraction as a function of the engine operating parameters. In the present study, the quantitative measurement technique of residual gas fraction was studied by using Fast Response Flame Ionization Detector(FRFID). The measuring technique and model for estimation of residual gas fraction were reported in this paper. By the assuming that the raw signal from FRFID saturates with the same slope for firing and misfiring cycle, in-cylinder hydrocarbon(HC) concentration can be estimated. Residual gas fraction can be obtained from the in-cylinder HC concentration measured at firing and motoring condition. The developed measurement and calibration procedure were applied to the limited engine operating and design condition such as intake manifold pressure and valve overlap. The results show relevant trends by comparing those from previous studies.

• Wind and Structures
• /
• v.22 no.1
• /
• pp.17-41
• /
• 2016

To address the uncertainty of the flight trajectories caused by the turbulence and gustiness of the wind field over the roof and in the wake of a building, a 3-D probabilistic trajectory model of flat-type wind-borne debris is developed in this study. The core of this methodology is a 6 degree-of-freedom deterministic model, derived from the governing equations of motion of the debris, and a Monte Carlo simulation engine used to account for the uncertainty resulting from vertical and lateral gust wind velocity components. The influence of several parameters, including initial wind speed, time step, gust sampling frequency, number of Monte Carlo simulations, and the extreme gust factor, on the accuracy of the proposed model is examined. For the purpose of validation and calibration, the simulated results from the 3-D probabilistic trajectory model are compared against the available wind tunnel test data. Results show that the maximum relative error between the simulated and wind tunnel test results of the average longitudinal position is about 20%, implying that the probabilistic model provides a reliable and effective means to predict the 3-D flight of the plate-type wind-borne debris.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.10
• /
• pp.620-629
• /
• 2005

In this paper, a new protocol-based approach was proposed for development of a ubiquitous vision system. It is possible to apply the approach by regarding the ubiquitous vision system as a multiagent system. Thus, each vision sensor can be regarded as an agent (vision agent). Each vision agent independently performs exact segmentation for a target by color and motion information, visual tracking for multiple targets in real-time, and location estimation by a simple perspective transform. Matching problem for the identity of a target during handover between vision agents is solved by the Identified Contract Net (ICN) protocol implemented for the protocol-based approach. The protocol-based approach by the ICN protocol is independent of the number of vision agents and moreover the approach doesn't need calibration and overlapped region between vision agents. Therefore, the ICN protocol raises speed, scalability, and modularity of the system. The protocol-based approach was successfully applied for our ubiquitous vision system and operated well through several experiments.

• Publications of The Korean Astronomical Society
• /
• v.18 no.1
• /
• pp.51-60
• /
• 2003

This paper is the research and development including the system design and the prototype system building of the 400MHz wide-band digital autocorrelation spectrometer system for radio astronomy observation, which will be used as back-end signal processing unit of the Dual channel SIS receiver at Taeduk Radio Astronomy Observatory. So in this paper, we performed development of the high speed digitizing sampler, the circular memory buffer, and the correlator module for the 400MHz wide-band digital autocorrelator. This developed system will be use at TRAO after the housing and some calibration.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.292-295
• /
• 2003

Moire topography method is a well-known non-contacting 3-D measurement method. the automatic 3-D measurement by moire topography has been required since the method was frequently applied to the engineering and medical fields. 3-D measurement using digital projection moire topography is very attractive because of its high measuring speed and high sensitivity. In this study, digital two-wavelength phase shilling moire is applied to the entertainment fields. recently. as promoting the growth of the VR-Game, display devices which attract public attention such as HMD or Projector are being appeared in order to deliver effectively the absorption sense. this study realized the Auto-calibrating system for arbitrary display surface using digital moire method which satisfied the shape measurement of display surface and the request of FOV(Field of View) output. also when large screen wasn't prepared, this auto-calibrating system was applied to enjoy games or movies at home with a projector and walls