• Journal of Welding and Joining
• /
• v.14 no.4
• /
• pp.53-61
• /
• 1996

It was attempted to improve the wear resistance of Al alloy under the load condition by making a formation of the thicker surface hardening alloy layers. The thicker surface hardening alloy layers were formed on 6061 Al alloys overlayed by MIG and TIG welding process with Cu powders feeding. The characteristics of hardening and wear resistance have been investigated in relation to the microstructures of alloyed layers, with a selection of optimum alloying conditions for formation of overlaying layer. The results obtained were summarized as follows With increasing feeding rate of Cu powders by MIG welding, the hardness and specific wear of the overlay weld alloys were increased. It is considered that these high hardness and specific wear of overlay weld alloys were due to the formation of Θ($Al_2Cu$) phases. With increasing feeding rate of Cu powders by TIG welding, the hardness and specific wear of the overlay weld alloys were increased in feeding rates 12 and 18g/min. However, the hardness and specific wear were decreased in the powder feeding rate 38g/min. It is considered that considered that decrease of hardness and specific wear in the powder feeding rate 38g/min due to formation of ${\gamma}$($Al_4Cu_9$) phases.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.317-327
• /
• 2012

The average specific cake resistance, the most important indicator for cake filtration and solid-liquid separation, is measured by filtration experiment. But the exact value is difficult to measure because of the other influences such as sedimentation during filtration. This study, a little more stable method named filtration-permeation is proposed for measuring average specific cake resistance. The filtration-permeation is composed of permeation of particle eliminated water through pre-formed cake by filtration. Using 1 wt% calcium carbonate suspension, the filtration-permeation experiments were performed for 8 kinds of filter media at the conditions of 0.5 atm and 0.2 atm, 1 and 3 sheets of filter media. At each specific condition, three to five times filtration-permeation were accomplished. As a result, stable permeation speed is measured. According to this experimental result, the characteristics of permeation and the effect of sedimentation are analyzed with Ruth's equation. The one way analysis of variance (one way ANOVA) is applied to the average specific cake resistances of filtration and permeation obtained with the selected three kinds of filter media. The average specific cake resistances between 0.5 atm and 0.2 atm by filtration do not distinguished, but those by permeation is perfectly distinguished. The experimental results during permeation have a very narrow distribution than that measured during filtration. The analysis of filtration experiments, it was verified that the resistance of filter medium by traditional method is of no significance. Finally, the migration of small particles through the medium composed of fiber glass at low pressure was studied.

• Coupled systems mechanics
• /
• v.2 no.1
• /
• pp.23-51
• /
• 2013

An analytical algorithm for the estimation of the resistance forces exerted on the dipper of a cable shovel and the specific energy consumed in the cutting-loading process is presented. Forces due to payload and to cutting of geomaterials under given initial conditions, cutting trajectory of the bucket, bucket's design, and geomaterial properties are analytically computed. The excavation process has been modeled by means of a kinematical shovel model, as well as of dynamic payload and cutting resistance models. For the calculation of the cutting forces, a logsandwich passive failure mechanism of the geomaterial is considered, as has been found by considering that a slip surface propagates like a mixed mode crack. Subsequently, the Upper-Bound theorem of Limit Analysis Theory is applied for the approximate calculation of the maximum reacting forces exerted on the dipper of the cable shovel. This algorithm has been implemented into an Excel$^{TM}$ spreadsheet to facilitate user-friendly, "transparent" calculations and built-in data analysis techniques. Its use is demonstrated with a realistic application of a medium-sized shovel. It was found, among others, that the specific energy of cutting exhibits a size effect, such that it decreases as the (-1)-power of the cutting depth for the considered example application.

• Membrane and Water Treatment
• /
• v.9 no.4
• /
• pp.245-253
• /
• 2018

The aim of this study is to investigate the membrane fouling in a thermophilic membrane bioreactor (TMBR) operated different sludge retention times (SRTs). For this purpose, TMBR was operated at four different SRTs (10, 30, 60 and 100 days). Specific cake resistance (${\alpha}$), cake resistance, gel resistance, total resistance, MFI (modified fouling index) and FDR (flux decrease ratio) were calculated for all SRTs. It was observed that flux in the membrane increases with rising SRT although the sludge concentrations in the TMBR increased. The steady state flux was found to be 31.78; 34.70; 39.60 and 43.70 LMH ($Liter/m^2/h$) for the SRTs of 10, 30, 60 and 100 days respectively. The concentrations of extracellular polymeric substance (EPS) and soluble microbial product (SMP) decreased with increasing SRT. The membrane fouling rate was higher at shorter SRT and the highest fouling rate appeared at an SRT of 10 d. Both the sludge cake layer and gel layer had contribution to the fouling resistance, but the gel layer resistance value was dominant in all SRTs.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.233-236
• /
• 2002

Some measures are provided for the optimum design of specific on-resistance $R_{on}$ and breakdown-voltage $V_B$ of interdigitated CB (Composite Buffer) MOSFET, including introducing opposite type impurity into the P region near the $N_＋$contact, separating P region from N region with an oxide film, and a groove in the N region near the $P_＋$ contact. The new relationship between the $R_{on}$ and $V_B$, which proved by numerical device simulation, are more exact and minute than the qualitative results before.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.506-511
• /
• 2001

Weld overlay has been developed to improve the property of material surface which is used in the severe environment. Weld overlay is the process which uses an arc heat and welds different composition of alloy on the substrate for the improvements of heat resistance and wear resistance. Weld overlay has a lot of advantages which are high hardness, good processing efficiency, easy controlling of layer thickness, good quality and low cost. In this study, weld overlay was performed by MAG welding on the base metal(SS400) with filler metal which contain composite powders(Cr+C+Mn+Mo+NbC) and solid wire(JIS-YGW11). Characterization of hardness and wear resistance were analyzed by EDS, EPMA, XRD and observations of microstructure were performed to investigate characteristics of overlays. The experimental results of overlaid specimens manufactured with Cr+C+Mn+Mo+NbC powders were obtained as fellows. ${\alpha}-phase$, M(Fe, Cr)3C and NbC of overlays were increased with decreasing the wire feed rates and increasing powder feed rates. Also the hardness of overlays were increased and the specific wear were decreased.

• Journal of Welding and Joining
• /
• v.20 no.3
• /
• pp.54-59
• /
• 2002

Overlays is a treatment of the surface and near-surface regions of a material to allow the surface to perform functions that are distinct from those frictions demanded far the bulk of the material. Welding, thermal spray, quenching, carburizing and nitration have been used as the surface treatment. Especially, weld overlay is a relatively thick layer of filler metal applied to a carbon or low-alloy steel base metal for the purpose of providing a wear resistant surface. In this study, weld overlay was performed by MAG welding on the base metal(SS400) with filler metal which contain composite powders($Cr_3C_2+Mn+Mo+NbC$) and solid wire(JIS-YGW11). Characteristics of hardness and wear resistance on overlays were analyzed by EDS, EPMA, XRD and microstructures. Carbide formations were $M(Cr, Fe)_7C_3$ and NbC phases. And carbide volume fraction, hardness and specific wear resistance of overlays were increased with increasing powder feed rate and decreasing wire fred rate. Hardness and wear resistance were almost proportioned to carbide volume fraction of overlay.

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.163-166
• /
• 2016

It is important to operate the driving circuit under the optimal condition through precisely sensing the power consumption causing the temperature made mainly by the MOSFET (metal-oxide semiconductor field-effect transistor) when a BLDC (Brushless Direct Current) motor operates. In this letter, a Super-junction (SJ) power TMOSFET (trench metal-oxide semiconductor field-effect transistor) with an ultra-low specific on-resistance of $0.96m{\Omega}{\cdot}cm^2$ under the same break down voltage of 100 V is designed by using of the SILVACO TCAD 2D device simulator, Atlas, while the specific on-resistance of the traditional power MOSFET has tens of $m{\Omega}{\cdot}cm^2$, which makes the higher power consumption. The SPICE simulation for measuring the power distribution of 25 cells for a chip is carried out, in which a unit cell is a SJ Power TMOSFET with resistor arrays. In addition, the power consumption for each unit cell of SJ Power TMOSFET, considering the number, pattern and position of bonding, is computed and the power distribution for an ANSYS model is obtained, and the SJ Power TMOSFET is designed to make the power of the chip distributed uniformly to guarantee it's reliability.

• Journal of Haehwa Medicine
• /
• v.9 no.2
• /
• pp.211-221
• /
• 2001

A literature study on oncological immune therapy was done, and the results were as follows. 1. Oncological immune therapy is classified as specific non specific therapy or active inactive therapy, and in tumor immune response, cellular immunity operates mainly, so activity of T lymphocytes and macrophages are closely related with growth, progress, metastasis and prospect of tumor. Recently, Immune therapies of gene which use cytokines and HLA-B7 are carrying out. 2. In oriental medicine, development of disease is closely related to up and down of healthy qi, so healthy qi operates as a immune factor and resistance factor. 3. On the base of theory "Increasing healthy qi reduces mass(養正則積自除)", strengthening body resistance is emphasized in cancer therapy. Also strengthening body resistance activates cellular immune response and promote killing tumor facility of T-cell. 4. In clinical view, using immune therapy after operation, radiation, and chemotheraphy is more effective than immune therapy itself, so it is expected that east-west cooperation will be effective in cancer therapy. 5. The study of oncological immunity is progressed on emphasizing T-cell and it is related to oriental medical theory "strengthening healthy qi to eliminate pathogen(扶定祛邪)" and advanced study is expected in future.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.25-26
• /
• 2008

Electrical properties of Pt/Ti/Au/Pt contacts to n-GaAs were characterized as the V/III ratio of GaAs grown by metalorganic chemical vapor deposition were 25, 50, and 100, respectively. The samples have been annealed during 30sec at 350 and $450^{\circ}C$ in rapid thermal annealing, and those specific contact resistance investigated by using transmission line method. According to experimental results, the specific contact resistance between p-metal and GaAs was decreased as the V/III ratio was lower. These results indicate that Si doping concentration of GaAs increased as the vacancy of V-series of GaAs was high.