• 한국안전학회지
• /
• 제16권4호
• /
• pp.160-167
• /
• 2001

Cracking in connote structures is one of the main issues of structural design next to ensuring the load-bearing capacity. Thermal analysis is used to prevent thermal mucking, but concrete properties are uncertain variable, and analysis results have uncertainty, too. In this study, sensitivity analysis is performed to investigate the effect of conductivity, specific heal and pouring temperature. The results show that lower conductivity and higher specific heat increase the maximum temperature and maximum tensile stress. The structure with internal restraint is mostly influenced by the change of conductivity and specific heat.

• International Journal of Internet, Broadcasting and Communication
• /
• 제12권2호
• /
• pp.37-44
• /
• 2020

The fifth generation (5G) mobile communication has been commercialized and the 5G applications, such as the artificial intelligence (AI) and the internet of things (IoT), are deployed all over the world. The 5G new radio (NR) wireless networks are characterized by 100 times more traffic, 1000 times higher system capacity, and 1 ms latency. One of the promising 5G technologies is non-orthogonal multiple access (NOMA). In order for the NOMA performance to be improved, sometimes the additive signal-dependent Gaussian noise (ASDGN) channel model is required. However, the channel capacity calculation of such channels is so difficult, that only lower and upper bounds on the capacity of ASDGN channels have been presented. Such difficulties are due to the specific constraints on the dependency. Herein, we provide the capacity of ASDGN channels, by removing the constraints except the dependency. Then we obtain the ASDGN channel capacity, not lower and upper bounds, so that the clear impact of ASDGN can be clarified, compared to additive white Gaussian noise (AWGN). It is shown that the ASDGN channel capacity is greater than the AWGN channel capacity, for the high signal-to-noise ratio (SNR). We also apply the analytical results to the NOMA scheme to verify the superiority of ASDGN channels.

• Journal of Microbiology and Biotechnology
• /
• 제23권5호
• /
• pp.715-718
• /
• 2013

Density of catalytic organisms can determine the biodegradation capacity and specific biodegradation rate (SBR). A new index, biodegradation capacity utilization (BCU, %), was developed for estimating the extent of actual biodegradation of a gas compound over the full capacity. Three methanotrophic cultures were serially diluted (1-1/25), and methane SBR and BCU were measured. Consistently, biomass reduction increased the SBR and decreased the BCU. Linearity (p < 0.05, r > 0.97) between the BCU and cell density indicated the reflection of biodegradation capacity by BCU. Therefore, BCU is indicative of whether the density of catalytic organisms is pertinent for SBR evaluation of low-soluble gaseous compounds.

• 한국수소및신에너지학회논문집
• /
• 제14권4호
• /
• pp.305-312
• /
• 2003

A study is presented of the adsorption capacity of a number of different activated carbons for hydrogen at 100 bar aad 298 K. The hydrogen adsorption isotherm was measured by isothermal gravimetric analysis, using a microbalance. The effect of activated carbon's porosity on hydrogen adsorption capacity is surveyed. It is concluded that hydrogen adsorption capacity of activated carbon is lineally increased according to the increase of specific surface area and total pore volume, It seems that microporosity is more contributive than mesoporosity. Most of the adsorbed quantity is due to physical adsorption and chemisorption is negligible, In this work, 0.79 wt.% of hydrogen adsorption capacity is reached.

• 동력기계공학회지
• /
• 제18권4호
• /
• pp.66-71
• /
• 2014

In this study, effect of heat treatment on the microstructure and damping capacity of hot rolled magnesium alloys was investigated. The microstructure of hot rolled magnesium consisted of dendrite structure and $Mg_{17}Al_{12}$ compounds precipitated along the grain boundry. The dendrite structure was dissipated and $Mg_{17}Al_{12}$ compounds was decomposed by annealing treatment, and then they dissolved in ${\alpha}-Mg$. With an increasing the annealing temperature and time, damping capacity was slowly increased by the growth of grain size and decreasing of defects induced by hot rolling. Two kinds of magnesium alloys AZ 31 and AZ 61 after annealing showed no difference in damping capacity.

• 공업화학
• /
• 제35권2호
• /
• pp.140-147
• /
• 2024

바이오매스 활용을 높이기 위하여, 열처리 공정을 통해 강아지풀 기반 리튬 이온 이차 전지용 탄소음극재(SV-C)를 제조한 뒤 전기화학적 성능을 고찰하였다. 강아지풀의 열처리 온도가 750 ℃로 낮을 때 낮은 결정성과 높은 비표면적(126 m²/g)과 함께, 표면에 많이 존재하는 산소의 (-) 전하가 리튬을 끌어당김으로 인하여 비정전용량(1003.3 mAh/g, at 0.1 C)이 높지만, 용량 유지율은 61.0% (at 500 cycles and 1 C)로 낮아지는 것으로 여겨진다. 또한, 열처리온도가 1150 ℃로 증가하면 탄소층이 축합되어 배열이 우수해짐에 따라 구조 결함이 감소하여 기공이 크게 줄어 비표면적(32 m²/g)이 감소한 것으로 확인되었다. 또한, 음극재 표면결함이 감소하여 결정성이 높아지게 되면, 용량 유지율은 89.7% (at 500 cycles and 1 C)로 높지만, 결함 정도가 작아 활성점이 줄어들어 비정전용량이 471.7 mAh/g로 매우 낮은 것으로 여겨진다. 본 연구 범위에서, 열처리 온도에 따라 제조된 강아지풀 기반 탄소음극재의 경우, 비표면적에 비해 표면 산소 함량과 결정성 등이 음극재의 전기화학적 특성에 더 높은 신뢰도를 갖는 것으로 나타났다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.305-310
• /
• 2001

Within some degree of journal misalignment, maximum pressure, maximum temperature, bearing load, friction and side leakage in high-speed journal bearing operation are examined under the condition of variable density and specific heat. The results are compared with the calculation results under the conditions of constant density and specific heat, and variable density and constant specific heat. It is found that the effects of variable density and specific heat on shaft misalignment are significant in determining the load capacity of a journal bearing operating at high speed.

• 한국전기전자재료학회논문지
• /
• 제19권7호
• /
• pp.636-643
• /
• 2006

Si-C materials were synthesized by the heating the mixture of silicon and polyvinylidene fluoride (PVDF). The electrochemical properties of the Si-C materials as the high capacitive anode materials of lithium secondary batteries were evaluated by the galvanostatic charge-discharge test through 2032 type $Si-C{\mid}Li$ coin cells. Charge-discharge tests were performed at C/10 hour rate(C = 372 mAh/g). Initial discharge and charge capacities of $Si-C{\mid}Li$ cell using a Si-C material derived from PVDF(20wt.%) were found to be 1,830 and 526 mAh/g respectively. The initial discharge-charge characteristics of the developed Si-C electrode were analyzed by the electrochemical galvanostatic test adopting the capacity limited charge cut-off condition(GISOC). The range of reversible specific capacity IIE(intercalation efficiency at initial discharge-charge) and IICs(surface irreversible specific capacity) were 216 mAh/g, 68 % and 31 mAh/g, respectively.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.45.2-45.2
• /
• 2011

Metal organic frameworks (MOF) have generated considerable interests as a potential candidate for hydrogen storage owing to their extremely high surface-to-volume ratio and low density. In this study, Pt nanoparticles of about 3 nm in size were introduced outside MOF-5 [$Zn_4O$(1,4-benzenedicarbocylate)3], which was then encapsulated with hydrophobic microporous carbon black (denoted CB@Pt/MOF-5) in order to enhance hydrogen uptake capacity without decreasing the specific surface area and hydrostability. To study the chemical composition, morphology, crystal information, and properties of the synthesized material, a variety of techniques is employed, including WXRD, XPS, ICP-AES, FE-SEM, HR-TEM, and N2 adsorption-desorption, confirming the formation of novel hybrid composite designated CB@Pt/MOF-5 with highly crystalline structure, large specific surface area and pore volume. In addition, $H_2$ storage capacity for resulting material was measured using magnetic suspension microbalance at 77 and 298 K under high-pressure condition, and the hydrostability was also tested by exposing the sample to 33% relative humidity at $23^{\circ}C$ and measuring XRD as a function of time.

• Structural Engineering and Mechanics
• /
• 제59권6호
• /
• pp.1095-1120
• /
• 2016

This paper investigates the change of structural characteristics of steel cable-stayed bridges after cable failure. Cables, considered as the intermediate supports of cable-stayed bridges, can break or fail for several reasons, such as fire, direct vehicle clash accident, extreme weather conditions, and fatigue of cable or anchorage. Also, the replacement of cables can cause temporary disconnection. Because of the structural characteristics with various geometric nonlinearities of cable-stayed bridges, cable failure may cause significant change to the structural state and ultimate behavior. Until now, the characteristics of structural behavior after cable failure have rarely been studied. In this study, rational cable failure analysis is suggested to trace the new equilibrium with structural configuration after the cable failure. Also, the sequence of ultimate analysis for the structure that suffers cable failure is suggested, to study the change of ultimate behavior and load carrying capacity under specific live load conditions. Using these analysis methods, the statical behavior after individual cable failure is studied based on the change of structural configuration, and distribution of internal forces. Also, the change of the ultimate behavior and load carrying capacity under specific live load conditions is investigated, using the proposed analysis method. According to the study, significant change of the statical behavior and ultimate capacity occurs although just one cable fails.