• Steel and Composite Structures
• /
• 제49권2호
• /
• pp.245-255
• /
• 2023

The present paper summarizes the results of an experimental program on the influence of using waste lathe scraps in the concrete mixture on the shear behavior of RC beams with different amounts of shear reinforcement. Three different volumetric ratios (1, 2 and %3) for the scraps and three different stirrup spacings (160, 200 and 270 mm) were adopted in the tests. The shear span-to-depth ratios of the beams were 2.67 and the stirrup spacing exceeded the maximum spacing limit in the building codes to unfold the contribution of lathe scraps to the shear resistances of shear-deficient beams, subject to shear-dominated failure (shear-tension). The experiments depicted that the lathe scraps have a pronounced contribution to the shear strength and load-deflection behavior of RC beams with widely-spaced stirrups. Namely, with the addition of 1%, 2% and 3% waste lathe scraps, the load-bearing capacity escalated by 9.1%, 21.8% and 32.8%, respectively, compared to the reference beam. On the other hand, the contribution of the lathe scraps to the load capacity decreases with decreasing stirrup spacing, since the closely-spaced stirrups bear the shear stresses and render the contribution of the scraps to shear resistance insignificant. The load capacity, deformation ductility index (DDI) and modulus of toughness (MOT) values of the beams were shown to increase with the volumetric fraction of scraps if the stirrups are spaced at about two times the beam depth. For the specimens with a stirrup spacing of about the beam depth, the scraps were found to have no considerable contribution to the load capacity and the deformation capacity beyond the ultimate load. In other words, for lathe scrap contents of 1-3%, the DDI values increased by 5-23% and the MOT values by 63.5-165% with respect to the reference beam with a stirrup spacing of 270 mm. The influence of the lathe scraps to the DDI and MOT values were rather limited and even sometimes negative for the stirrup spacing values of 160 and 200 mm.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제28권3호
• /
• pp.47-58
• /
• 2024

This study were conduced experimentally to analyze the heat-generating performance, flexural strength, and microstructure of conductive mortar mixed with micro steel fiber and multi-wall carbon nanotube (MWCNT). In the conductive mortar heat-generating performance and flexural strength tests, the mixing concentration of MWCNT was selected as 0.0wt%, 0.5wt%, and 1.0wt% relative to the weight of cement, and micro steel fibers were mixed at 2.0vol% relative to the volume. The performance experiments were conducted with various applied voltages (DC 10V, 30V, 60V) and different electrode spacings (40 mm, 120 mm) as parameters, and the flexural strength was measured at the curing age of 28 days and compared and analyzed with the normal mortar. Furthermore, the surface shape and microstructure of conductive mortar were analyzed using a field emission scanning electron microscope (FE-SEM). The results showed that the heat-generating performance improved as the mixing concentration of MWCNT and the applied voltage increased, and it further improved as the electrode spacing became narrower. However, even if the mixing concentration of MWCNT was added up to 1.0 wt%, the heat-generating performance was not significantly improved. As a result of the flexural strength test, the average flexural strength of all specimens except the PM specimen and the MWCNT mixed specimens was 4.5 MPa or more, showing high flexural strength due to the incorporation of micro steel fibers. Through FE-SEM image analysis, Through FE-SEM image analysis, it was confirmed that a conductive network was formed between micro steel fibers and MWCNT particles in the cement matrix.

• Journal of the Microelectronics and Packaging Society
• /
• 제24권4호
• /
• pp.23-29
• /
• 2017

The packaged optical fiber Bragg grating sensors which were networked by multiplexing the Bragg grating sensors with WDM technology were investigated in application for the structural health monitoring of the marine trestle structure transporting the ship. The optical fiber Bragg grating sensor was packaged in a cylindrical shape made of aluminum tubes. Furthermore, after the packaged optical fiber sensor was inserted in polymeric tube, the epoxy was filled inside the tube so that the sensor has resistance and durability against sea water. The packaged optical fiber sensor component was investigated under 0.2 MPa of hydraulic pressure and was found to be robust. The number and location of Bragg gratings attached at the trestle were determined where the trestle was subject to high displacement obtained by the finite element simulation. Strain of the part in the trestle being subjected to the maximum load was analyzed to be ${\sim}1000{\mu}{\varepsilon}$ and thus shift in Bragg wavelength of the sensor caused by the maximum load of the trestle was found to be ~1,200 pm. According to results of the finite element analysis, the Bragg wavelength spacings of the sensors were determined to have 3~5 nm without overlapping of grating wavelengths between sensors when the trestle was under loads and thus 50 of the grating sensors with each module consisting of 5 sensors could be networked within 150 nm optical window at 1550 nm wavelength of the Bragg wavelength interrogator. Shifts in Bragg wavelength of the 5 packaged optical fiber sensors attached at the mock trestle unit were well interrogated by the grating interrogator which used the optical fiber loop mirror, and the maximum strain rate was measured to be about $235.650{\mu}{\varepsilon}$. The modelling result of the sensor packaging and networking was in good agreements with experimental result each other.

• Korean Journal of Weed Science
• /
• 제2권1호
• /
• pp.1-6
• /
• 1982

An experiment was conducted to obtain the basic information about competitive ability of rice against weeds as affected by eco-geographic race and plant spacing. Generally, more weeds were grown at the plot of Japonica-type cultivar, (Nakdongbyeo) compared to Tongiltype cultivar (Seogwangbyeo). The degree of weed suppression was highest at the 10 ${\times}$ 10cm plant spacing while no difference was observed between 30 ${\times}$ 15cm and 40 ${\times}$ (10 ${\times}$ 10 cm) plant spacings in both cultivar;. In all treatments except the plot of 10 ${\times}$ 10 cm plant spacing of Seogwangbyeo, singnificant amount of weeds was higher for no weeding plot compared to hand weeding plot. Grain yield loss due to weed competition was the highest at the 40 ${\times}$ (10 ${\times}$ 10cm) plant spacing and followed by 30 ${\times}$ 15cm and 10 ${\times}$ 10cm plant spacing, in order, for Seogwangbyeo. However, for Nakdongbyeo, the highest grain yield loss was obtained from the 30 ${\times}$ 15cm plant spacing and grain yield was not affected at the 10 ${\times}$ 10cm plant spacing. Rice grain yield was highly correlated with weed weight for both cultivars (Seogwangbyeo; Y = 5.44 - 0.0128 X, r = -0.929$^{**}$, Nakdongbyeo; Y = 4.96 - 0.0103 X, r = -0.934$^{**}$). To reduce grain yield by 50%, weed weight of 212.5g/sq.m for Seogwangbyeo and 241g/sq.m for Nakdongbyeo was needed, respectively. This result implied that Nakdongbyeo was more competitive against weeds compared to Seogwangbyeo.

• Journal of the Mineralogical Society of Korea
• /
• 제21권3호
• /
• pp.313-320
• /
• 2008

Hectorite was synthesized under hydrothermal conditions and its physicochemical properties have been investigated in terms of temperature, pH, and organic agent to observe the change of doll basal spacing. The IR, CEC, MB, swelling volume and specific surface area of the hectorite were measured for the characterization. The solid/liquid ratio of hectorite to distilled water before mixing with other materials was also determined for its use as a multi-functional material. The $d_{001}$ basal spacing decreased from $12.63\;\AA$ at room temperature to $10.19\;\AA$ at $650^{\circ}C$ in the heating tests. As the pH of hectorite slurry increased. the $d_{001}$ basal spacing decreased. reaching the lowest value of $13.33\;\AA$ at pH 7 and afterward, increased. All the fool basal spacings of the hectorite increased when it was intercalated with the following solvents: $12.86\;\AA$ in diethyl ether, $13.31\;\AA$ in acetonitrile. $13.59\;\AA$ in methanol, $14.05\;\AA$ in ethanol, $15.69\;\AA$ in acetone, and $17.42\;\AA$ in ethylene glycol. Our IR analysis results were in good agreement with those of other researchers. The CEC, MB, swelling volume and specific surface area of hectorite were determined to be 105 cmol/kg, 80 cmol/kg, $68\sim74ml/2g$ and $213m^{2}/g$, respectively. Also, the hectorite to distilled water ratio of 2 to 100 was found to be most favorable for mixing with other materials such as the solvents mentioned above.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• 제37권4호
• /
• pp.361-371
• /
• 1992

For the increase of grain yield potential in rice, a low-tillering large panicled type has been suggested as an ideotype. A low-tillering plant type may have different yield potential and needs different cultural practices from that used in a high-tillering type for the maximum yield. This study was conducted to evaluate the grain yield performances of a low-tillering large panicled rice and high-tillering small panicled rice at different plant spacings, nitrogen(N) levels and seedling numbers per hill. A low-tillering large panicled genotype, IR25588 was compared with a high-tillering small panicled IR58. The grain yield of IR25588 was significantly higher than that of IR58 under a narrow spacing with high N level. The maximum yields of IR58 and IR25588 were reached at about 35,000 and 40,000 spikelets per m$^2$, respectively. The increased grain yield in IR25588 was mainly due to the increase in spikelet number per unit area which is the most precise indicator of grain yield in rice. The optimum spacing for the maximum yield was denser for IR25588 than that for IR58 under high N level. The intra-hill competition of the low-tillering type was lower than that of the high-tillering type. The higher dry matter production and bigger leaf area and culm weight were the main factors for increased grain yield in a low-tillering panicle weight type. Based on the results, the yield potential of a low-tillering panicle weight type was higher than that of a high-tillering panicle number type, especially under a close spacing with high N level.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• 제6권3호
• /
• pp.217-224
• /
• 2008

In deep geological disposal system, the integrity of a disposal canister having spent fuels is very important factor to assure the safety of the repository system. This disposal canister is one element of the engineered barriers to isolate and to delay the radioactivity release from human beings and the environment for a long time so that the toxicity does not affect the environment. The main requirement in designing the deep geological disposal system is to keep the buffer temperature below 100$^{\circ}C$ by the decay heat from the spent fuels in the canister in order to maintain the integrity of the buffer material. Also, the disposal canister can endure the hydraulic pressure in the depth of 500 m and the swelling pressure of the bentonite as a buffer. In this study, new concept of the disposal canister for the CANDU spent fuels which were considered to be disposed without any treatment was developed and the thermal stability and the structural integrity of the canister were analysed. The result of the thermal analysis showed that the temperature of the buffer was 88.9$^{\circ}C$ when 37 years have passed after emplacement of the canister and the spacings of the disposal tunnel and the deposition holes were 40 m and 3 m, respectively. In the case of structural analysis, the result showed that the safety factors of the normal and the extreme environment were 2.9 and 1.33, respectively. So, these results reveal that the canister meets the thermal and the structural requirements in the deep geological disposal system.

• The Journal of the Petrological Society of Korea
• /
• 제16권3호
• /
• pp.144-161
• /
• 2007

The studied Nangsan area is widely covered by the Jurassic biotite granodiorite, which is mainly light grey in color and medium-grained in texture. Results of the regional fracture pattern analysis for the granodiorite body are as follows. Strike directions of fractures show three dominant sets in terms of frequency order. The sets are in an order of a (1) $N80^{\circ}{\sim}90^{\circ}E$ (1st-order)>(2) $N70^{\circ}{\sim}80^{\circ}E$ (2nd-order)>(3) $NS{\sim}N10^{\circ}E$ (3rd-order). Spacings of the fractures are mostly predominant in less than 200 cm. Therefore, the granodiorite of the area has more potential for non-dimensional stones than dimension ones. And orientations of vertical quarrying planes can be also divided into two groups in terms of frequency $N14^{\circ}W{\sim}N16^{\circ}E$ (1st-order) and (2) $N78^{\circ}E{\sim}N88^{\circ}E$ (2nd-order). The orientations of the two groups are more or less different from those of the regional fracture patterns. These can be mainly attributed to the preferred orientations of microcrack developed in the quarries. Of physical properties, specific gravity, absorption ratio, porosity, compressive strength, tensile strength and abrasive hardness are 2.65, 0.28%, 0.73%, $1,628kg/cm^2,\;100kg/cm^2$ and 31, respectively. Contrary to the porosity, both granites of the Nangsan and Sogrisan areas show almost similar values of the abrasive hardness. These can be explained by the differences of Qz+Af modes, which can be regarded as an index for abrasive resistance. Meanwhile, it is anticipated that comprehensive understanding of the orientations of vertical quarrying planes and characteristics of various physical properties will be utilized as an important information for stone resources.

• Journal of the Korean earth science society
• /
• 제28권2호
• /
• pp.187-201
• /
• 2007

The first magnetotelluric (MT) transect across the Korean Peninsula was obtained traversing from the East Sea shoreline to the Yellow Sea shoreline. The MT survey profile was designed perpendicular to the strike of the principal geologic structure of the Korean Peninsula $(N30^{\circ}E)$, so-called 'China direction'. MT data were achieved at 50 sites with spacings of $3{\sim}8km$ along the 240 km survey line. The impedance responses are divided into four subsets reflecting typical geological units: the Kyonggi Massif, the Okchon Belt, the western part of the Kyongsang Basin, and the eastern part of the Kyongsang Basin. In the western part of the Kyongsang Basin, the thickness of the sedimentary layer is estimated to be about 3 km to 8 km and its resistivity is a few hundred ohm-m. A highly conductive layer with a resistivity of 1 to 30 ohm-m was detected beneath the sedimentary layer. The MT data at the Okchon Belt show peculiar responses with phase exceeding $90^{\circ}$. This feature may be explained by an electrically anisotropic structure which is composed of a narrow anisotropic block and an anisotropic layer. The Kyonggi Massif and the eastern part of Kyongsang Basin play a role of window to the deep geoelectrical structure because of the very high resistivity of upper crust. The second layers with highest resistivities in 1-D conductivity models occupy the upper crust with thicknesses of 13 km in the Kyonggi Massif and 18 km in the eastern Kyongsang Basin, respectively.

• Korean Journal of Weed Science
• /
• 제1권1호
• /
• pp.44-51
• /
• 1981

An experiment was conducted to obtain the basic information about competitive ability of rice against weeds as affected by culm length at the Yeongnam Crop Experiment Station, Office of Rural Development in 1980. More weeds were harvested from the plot of short statured cultivar, Manseogbyeo compared to the plot of Cheongcheongbyeo that was approximately 10cm taller than Manseogbyeo regardless of planting density variables. Weeds also decreased as rice population increased from $30{\times}15cm$, $40{\times}(10{\times}10cm)$ and to $10{\times}10cm$, in order. The degree of weed suppression and floristic composition was varied depending upon plant spacing and weeding regime subjected at the previous year. The degree of weed suppression became increased with increasing rice population. The degree of weed suppression at the $10{\times}10cm$ plant spacing showed as high as hand weeding subjected in the previous year. However, in terms of floristic composition, Scirpus hotarui Roxb. became dominant when rice had cultivated at $10{\times}10cm$ plant spacing in the previous year while S. hotarui and Sagittaria pygmaea Miq. were both important in the hand weeding plot. The highest grain yield of rice showed at the $10{\times}10cm$ plant spacing while no significant difference was observed between $40{\times}(10{\times}10cm)$ and $30{\times}15cm$ plant spacings for both weeding regimes and both cultivars. However, response of grain yield to weeding regime was differed in two cultivars. For Manseobgyeo, significant grain yield decreased in no weeding plot regardless of plant spacing variables. But in case of Cheongcheongbyeo, grain yield reduction was only recognized at the $30{\times}15cm$ plant spacing. Based on these result it could be concluded that Cheongcheongbyeo (10cm taller in height) seemed to be more competitive against weeds than Manseogbyeo.