• Environmental Engineering Research
• /
• 제20권4호
• /
• pp.397-402
• /
• 2015

SCR has been popularly approved as one of the most effective means for NOx emission control in heavy-duty and medium-duty vehicles currently. However, high urea dosing would lead to ammonia slip. And $NH_3$ sensor for vehicle emission applications has not been popularly used in real applications. This paper presents experimental studies on the diesel engine urea-SCR system by using a double NOx sensor system that is arranged in the downstream of the SCR catalyst based on ammonia cross-sensitivity. It was shown that the NOx conversion efficiency rised as $NH_3/NOx$ increases and the ammonia slip started from the $NH_3/NOx$ equal to 1.4. The increase of temperature caused high improvement of the SCR reaction rate while the space velocity had no obvious change. The ammonia slip was in advance as catalyst temperature or space velocity increase and the ammonia storage reduced as catalyst temperature or space velocity increase. The NOx real-time conversion efficiency rised as the ammonia accumulative storage increase and reached the maximum value gradually.

• 한국태양에너지학회 논문집
• /
• 제35권5호
• /
• pp.1-10
• /
• 2015

Whereas recent domestic buildings and industrial facilities are being constructed as large as possible, the daylighting systems for the large space have rarely been developed. Domestic situation has been reported as only several small or medium sized daylighting systems have been developed, and the large scaled systems have entirely being imported from abroad. We have developed a large scaled daylighting system for the big space. The developed system have been evaluated in terms of the average system efficiency and daylighting factor. Each results are shown with tabulated experimental data.

• 한국분무공학회지
• /
• 제21권2호
• /
• pp.71-77
• /
• 2016

Air pollutants nitrogen oxides are inevitably generated in the combustion reaction. Its amount trend is steadily increasing because the rapid modern industrialization and population growth. For this reason, NOx is controlled to reducing the harmful components in the exhaust gas. So Marine Environment Protection Committee (MEPC) take effect 'Tier I', 'Tier II' of air pollution regulation in 2005 and 2011 respectively. According to NOx emissions are strictly regulated management of the vessel through them. In addition, since 2016 the regulation enter into force in the next step 'Tier III' was confirmed by MEPC 66th committee. It's 80% enhanced emissions limits than the 'Tier I' Alternatively these emission regulation, research is actively being carried out about exhaust gas after-treatment methods through the vessel application of Selective Catalytic Reduction(SCR). Therefore depending on the basic specification of cell density according to the Area velocity, Space velocity, Linear velocity is studied the effects of NOx removal efficiency

• 한국디지털건축인테리어학회논문집
• /
• 제9권3호
• /
• pp.25-35
• /
• 2009

This study is planning improvement of welfare facilities about the hall for the aged in apartment housing. An apartment house, famous residential type in Korea, put an important value on its convenience and economical efficiency of furniture arrangement by maximizing floor space index. In this regard, leisure usage of house was not carefully considered for the aged people. To redefine the efficiency of welfare facilities, research mainly deals with analysis of realistic needs for the aged through the spot survey and interview. The main purpose of this study is to enhance the quality of welfare facilities and propose the improved welfare facilities for the aged people. Through the research, conclusions are as followed First, Facility standard and provisions of the law should be revised for considering population growth of the aged people. Second, there are 4 plan types in the hall for the aged. Contrary to our expectation, diversity of program was not found however various program planning is needed for considering its different types of plan. Third, according to regulation, space restriction is based on the number of households. Therefore, room and space standard does not depend on the number of people. From now on, in order to improve quality of welfare facilities of the aged, revision of laws and overall facility standard should be implemented in advance.

• International Journal of Fluid Machinery and Systems
• /
• 제9권3호
• /
• pp.256-264
• /
• 2016

To meet the demand of higher handling capacity, a mixed-flow submersible deep well pump was designed and tested. The main hydraulic components are made of plastics, which is free of erosion, light-weight, and environment-friendly. To simplify plastic molding process, and to improve productivity, an axial-radial guide vane was proposed. To clarify its effect on the performance, a radial guide vane and a space guide vane are developed as well. By comparison, the efficiency of the pump equipped with the axial-radial guide vane is higher than the radial guide vane and is lower than the space guide vane, and its high efficiency range is wide. The static pressure recovery of the axial guide vane is a bit lower than the space guide vane, but it is much larger than the radial guide vane. Taking the cost and molding complexity into consideration, the axial-radial guide vane is much economic, promoting its popularity for the moderate and high specific speed submersible deep well pumps.

• 한국소음진동공학회논문집
• /
• 제15권2호
• /
• pp.161-168
• /
• 2005

The absorbing material is mostly used to changing the acoustic energy to the heat energy in the passive control, and that consists of the porous media. That controls an air borne noise while the stiffened plates, damping material and additional mass control a structure borne noise. The additional mass can decrease the sound by mass effect and shift of natural frequency, and damping material can decrease the sound by damping effect. The passive acoustic control using these kinds of control materials has an advantage that is possible to control the acoustic in the wide frequency band and the whole space at a price as compared with the active control using the various electronic circuit and actuator. But the space efficiency decreased and the control ability isn't up to the active control. So it is necessary to maximize the control ability in the specific frequency to raise the capacity of passive control minimizing the diminution of space efficiency such an active control. Therefore, the characteristics of control materials and the optimum layout of control materials that attached to the boundary of structure-acoustic coupled cavity were studied using sequential optimization on this study.

• 설비공학논문집
• /
• 제26권11호
• /
• pp.535-540
• /
• 2014

This paper investigates the exhaust effectiveness of smoke, in the case of fire in a large atrium space. Numerical analysis was conducted to simulate transient fire growth in a test room, modeled by the Murcia atrium fire test. Various indices representing the exhaust performance of the exhaust system were obtained, such as the height of the smoke layer, and the instantaneous and accumulative capture efficiency of the smoke. The residual life time of smoke from the fire was also obtained, by injecting tracer gases at the fire location, depending on the airflow rate, and the location of the exhausts. The capture efficiency based on smoke concentration at the exhausts exhibits how much smoke can be removed by the exhaust system; whereas, the exhaust effectiveness based on residual life time indicates how rapidly the smoke can reach the exhaust locations, before being exhausted. The definitions and meanings of the indices to be used in representing the exhaust performance of a smoke exhaust system installed in a large space are discussed.

• 산업공학
• /
• 제12권1호
• /
• pp.10-18
• /
• 1999

Job shop manufacturing environments are using the concept of cellular manufacturing systems(CMS) which has several advantages in reducing production lead times, setup times, work-in-process, etc. Utilizing the similarities between cell-machine, part-machine, and the shape/size of parts, CMS can group machines and parts resulting in improved efficiency of this system. However, when grouping machines and parts in machine cells, there inevitably occurs exceptional elements(EEs), which can not operate in the same machine cell. Minimizing these EEs in CMS is a critical point that improving production efficiency. Constraints in machine duplication cost, machining process technology, machining capability, and factory space limitations are main problems that prevent achiving the goal of maintaining an ideal CMS environment. This paper presents an algorithm that minimizes EEs under the constraints of machine duplication cost and factory space limitation. Developing exceptional operation similarity(EOS) by cell-machine incidence matrix and part-machine incidence matrix, it brings the machine cells that operate the parts or not. A mathematical model to minimize machine duplication is developed by EOS, followed by a heuristic algorithm in order to reflect dynamic situation resulting from minimizing exceptional elements process and the mathematical model. A numerical example is provided to illustrate the algorithm.

• 한국통신학회논문지
• /
• 제30권1C호
• /
• pp.18-24
• /
• 2005

본 논문에서는 고속의 데이터 전송을 위해 APSK (Amplitude/Phase Shift Keying) 신호 기반 DUSTM(Differentail Unitary Space-Time Modulation) 기법과 트렐리스 코드를 결합하여 새로운 TC-DUSTM (Trellis Coded DUSTM) 기법을 제안한다. 특히, APSK 신호 기반 TC-DUSTM (trellis coded DUSTM) 기법에 적합한 트렐리스 코드 설계 방법을 제안한다. 모의실험을 통해 제안된 TC-DUSTM 기법은 높은 전송률에서 기존의 PSK 신호 기반 TC-DUSTM 기법에 비하여 비트 오류 확률 성능이 향상됨을 알 수 있다. 또한, 제안된 기법이 빠른 페이딩 채널 환경에서 발생되는 차동 기법의 irreducible error를 효율적으로 줄일 수 있음을 모의실험을 통하여 확인할 수 있다.

• 한국전산구조공학회논문집
• /
• 제14권3호
• /
• pp.361-369
• /
• 2001

이 연구는 공간 트러스의 비선형 해석을 위한 해석기법의 수치해석적 효율성에 관한 것으로써, 좌굴 이후의 거동 파악이 가능한 복합 호장법을 제안하였다. 복합 호장범은 현 강성변수를 제어변수로 사용하여, 안정구간에서는 선취법이 첨가된 Secant-Newton법을 사용하여, 불안정구간에서는 가속법이 첨가된 호장법을 사용하는 방법이다. 해석기법의 효율성을 비교하기 위하여 제시된 수지예제에 대한 해의 정확성, 수렴성, 계산시간을 기존의 호장법과 비교하였다. 공간 트러스의 기하학적 비선형 해석에 있어서는 이 연구에서 제안된 복합 호장법이 기존의 호장법보다 수치 해석적 효율성이 뛰어난 것을 알 수 있었다.