• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.8
• /
• pp.325-330
• /
• 2016

This study was conducted to develop a heating system for a fuel cell-driven electric vehicle. The system consists of a compressor, an expansion device and three heat exchangers. A conventional air source heat exchanger is used as primary heat exchanger of the system, and an additional water source heat exchanger is used as a pre-heater to supply heat to the upstream air of the primary heat exchanger. On the other hand, the third heat exchanger consists of a water-to-refrigerant heat exchanger. The heat source of the pre-heater and the water-refrigerant heat exchanger is the waste heat from the fuel cell's stack. In the experiment, the indoor and the outdoor air temperature were fixed, and the compressor speed, EEV opening and waste heat temperature were varied. The results indicate that the $COP_h$ of the proposed system is 3.01 when the system is operating at a 1,200 rpm compressor speed, 50% EEV opening, and $50^{\circ}C$ waste heat source temperature in air pre-heater operation. However, when the system uses a water-refrigerant heat exchanger, the $COP_h$ increases to up to 9.42 at the same compressor speed and waste heat source temperature with 75% EEV openings.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2019.05a
• /
• pp.195-196
• /
• 2019

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11a
• /
• pp.184-184
• /
• 2005

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2019.05a
• /
• pp.289-290
• /
• 2019

• Journal of environmental and Sanitary engineering
• /
• v.17 no.3
• /
• pp.52-59
• /
• 2002

Pilot-scale PSSBR(Phase Separated Sequencing Batch Reactor) was operated to evaluate requirement of external carbon sources(${\Delta}gCOD/{\Delta}gNO_3^{-}-N$) in denitrification. Methanol and fermented food waste were used as external carbon sources. Methanol and fermented food waste were fed to the anoxic state of first reactor and concentration were 50 and 40 mgCOD/L on the basis of concentration in reactor, respectively. In case that external carbon source was not used, average $NO_3^{-}-N$ concentration in effluent was 22.49 mg/L. When methanol and fermented food waste were fed, average $NO_3^{-}-N$ concentration in effluent were 10.13 mg/L and 6.3 mg/L, respectively and requirement of external carbon sources were 4.04 and 2.5 ${\Delta}gCOD/{\Delta}gNO_3^{-}-N$, respectively. Fermented food waste was better than methanol in denitrification efficiency. Therefore fermented food waste could be one of the excellent external carbon sources for nitrogen removal in biological nutrient removal process.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2018.11a
• /
• pp.109-110
• /
• 2018

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2019.05a
• /
• pp.343-344
• /
• 2019

• The Korean Journal of Food And Nutrition
• /
• v.11 no.6
• /
• pp.606-611
• /
• 1998

For waste recyle, we were investigated on Gardenia blue color production using Gardenia by-product by Bacillus subtilits. Optimum conditions for producing blue pigment were found to be 30$^{\circ}C$, initial pH 6.5, glucose as a carbon source 3% and yeast extract as a nitrogen source 0.5%, respectively. Optimum conditions for fermentor culture were agitation speed 400rpm, aeration 2 vvm and inoculum 5%. The optimum perculture time for inoculum was 20 hrs for blue pigment production.

• Nuclear Engineering and Technology
• /
• v.43 no.2
• /
• pp.149-158
• /
• 2011

Metal waste generated from the pyroprocessing of 10 MtU of spent fuel was classified by comparing the specific activity of a relevant radionuclide with the limit value of the specific activity specified in the Korean acceptance criteria for a lowand intermediate-level waste repository. A Korean Optimized Fuel Assembly design with a 17${\times}$17 array, an initial enrichment of 4.5 weight-percent, discharge burn-up of 55 GWD/MtU, and a 10-year cooling time was considered. Initially, the mass and volume of each structural component of the assembly were calculated in detail, and a source term analysis was subsequently performed using ORIGEN-S for these components. An activation cross-section library generated by the KENO-VI/ORIGEN-S module was utilized for top-end and bottom-end pieces. As a result, an Inconel grid plate, a SUS plenum spring, a SUS guide tube subpart, SUS top-end and bottom-end pieces, and an Inconel top-end leaf spring were determined to be unacceptable for the Gyeongju low- and intermediate-level waste repository, as these waste products exceeded the acceptance criteria. In contrast, a Zircaloy grid plate and guide tube can be placed in the Gyeongju repository. Non-contaminated Zircaloy cladding occupying 76% of the metal waste was found to have a lower level of specific activity than the limit value. However, Zircaloy cladding contaminated by fission products and actinides during the decladding process of pyroprocessing was revealed to have 52 and 2 times higher specific activity levels than the limit values for alpha and $^{90}Sr$, respectively. Finally, it was found that 88.7% of the metal waste from the 17${\times}$17 Korean Optimized Fuel Assembly design should be disposed of in a deep geological repository. Therefore, it can be summarized that separation technology with a higher decontamination factor for transuranics and strontium should be developed for the efficient management of metal waste resulting from pyroprocessing.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.12
• /
• pp.979-986
• /
• 2003

The performance characteristics of heating and cooling operation for a heat pump system using seawater heat source and exhaust energy are presented. The heat pump system is made of a waste heat recovery system and a vapor compression refrigeration system. The working fluid is R-22. The heat pump system COPs are measured during heating and cooling operation modes, and the resultant COPs were 9.7 and 7.9, respectively, which are three times higher than those of the heat pump itself. Therefore, the performance of the heat pump system using exhaust energy is excellent compared to that of a general heat pump. The experimental data can be effectively used for the design of the high efficient heat pump using a seawater heat source.