• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.5
• /
• pp.999-1003
• /
• 1992

Because of low noise and small size with huge capacity, a centrifugal fan is widely used for ventilation, air-conditioner and so on, which are very near to human life. Because of the complexity of its vibration and noise generation mechanics, most of researches on them are based on experimental methods. This study is to characterize the centrifugal fan noise and vibration. It is considered that noise is composed of the structural vibration noise and the air flow induced aerodynamic noise. To decouple the structural vibration noise the centrifugal fan is masked with an adhesive tape, such that air blowing is prohibited thus only the structural vibration noise is extracted. The noise level and characteristics in the frequency domain are verified and compared with those of total mixed one. This study shows some significant results that the structural vibration noise has relatively narrow band power spectrum compared with the total mixed one and has a strong periodicity. The sound level is lowered about 5dB by the removal of air flow with the masked fan for an air-conditioner used in this study.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.11C
• /
• pp.1573-1580
• /
• 2004

In this paper, an adaptation mode controller for adaptive microphone array system is proposed for high-quality speech acquisition in real environments. To ensure proper adaptation of the adaptive array algorithm, the proposed adaptation mode controller uses not only temporal information, but also spatial information. The proposed adaptation mode controller is constructed with two processing stages: an initialization stage and a running stage. In the initialization stage, a sound source localization technique is adopted, and a signal correlation characteristic is used in the running stage. For the adaptive may algorithm, a generalized sidelobe canceller with an adaptive blocking matrix is used. The proposed adaptation mode controller can be used even when the adaptive blocking matrix is not adapted, and is much stable than the power ratio method. The proposed algorithm is evaluated in real environment, and simulation results show 13dB SINR improvement with the speaker sitting 2m distance from the may.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.1
• /
• pp.179-185
• /
• 2012

Since the eco-era is getting closer, the importance of noise reducing in the passenger cars of high-speed train is very important. The active noise control is best choice to reduce low frequency noise because the passive one is too heavy for high speed trains where weight is so critical. Also ANC is able to reduce the ambient noise when the environmental-factor changes. To reduce a three-dimensional closed-space sound field like a car of a high-speed rail is hard to do using single channel ANC control system. We used multi-channel FXLMS algorithm which calculation speed is fast and the secondary path estimation is possible in order to take into account the physical delay in electro acoustic hardware control loudspeaker and power amplifier. Firstly, we have measured interior noise of KTX and estimated noise path in KTX test-bed. However there was some problem related to algorithm divergence and increasing the filter order. We have made a simulation of interior environment of KTX car by using three frequency bands of 120Hz, 280Hz, 360Hz as the most important for KTX ANC system. During this research the interior noise reduction of KTX car was made by using the multi-channel FXLMS algorithm. Reduction performance was evaluated and compared each other for open space section and tunnel section. in-situ experiment for the KTX noise reduction by proposed ANC was performed based on data obtained in simulation and they were compared for open space section and tunnel section as well.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.54-56
• /
• 2005

In this paper, we investigated the quench characteristics of HTSC elements in the integrated three-phase flux-lock type SFCL according to fault types such as the single-line-to-ground fault, the double-line-to-ground fault, the line-to-line fault and the three-line-to-ground fault. The integrated three-phase flux-lock type SFCL was the upgrade version of the single-phase flux-lock type SFCL. The structure of the integrated three-phase flux-lock type SFCL consisted of three-phase flux-lock reactor wound on an iron core with the ratio of the same turn between coil 1 and coil 2 in each phase. When the SFCL is operated under the normal condition, the flux generated in the iron core is zero because the flux generated between two coils of each single phase is canceled out. Therefore, the SFCL's impedance is zero, and the SFCL has negligible influence on the power system. However, if a fault occurs in any single-phase among three phases, the flux generated in the iron core is not zero any more. The flux makes HTSC elements of all phases quench irrespective of the fault type, which reduces the current of fault phase as well as the current of sound phase. It was observed that the fault current limiting characteristics of the suggested SFCL were dependent on the quench characteristics of HTSC elements in all three phases.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.960-962
• /
• 2005

In this paper, we investigated the quench characteristics of high-Tc superconducting(HTSC) elements in the integrated three-phase flux-lock type superconducting fault current limiter(SFCL) according to fault types such as the single-line-to-ground fault, the double-line-to-ground fault, the line-to-line fault and the triple-line-to-ground fault. The integrated three-phase flux-lock type SFCL is an upgrade version of single-phase flux-lock type SFCL. The structure of the integrated three-phase flux-lock type SFCL consisted of a three-phase flux-lock reactor wound on an iron core with the ratio of the same turn between coil 1 and coil 2 in each phase. When the SFCL is under the normal condition, the flux generated in the iron core is zero because the flux generated between two coils of each single phase is canceled out. Therefore, the SFCL's impedance is zero, and the SFCL has negligible influence on the power system. However, if a fault occurs in any single one of three phases, the flux generated in the iron core is not zero any more. The flux makes HTSC elements of all phases to quench irrespective of the fault type, which reduces the current in fault phase as well as the current of sound phase. It was obtained that the fault current limiting characteristics of the suggested SFCL were dependent on the quench characteristics of HTSC elements in all three phases.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.1003-1009
• /
• 2012

An instantaneous environmental noise simulation method emitted by a moving high-speed train by quasi-stationary analysis is proposed in this study. In the method, the propagation attenuations from stationary point sources on segmented railways to a receiver are calculated using a general purpose environmental noise prediction program ENPro based on the ISO 9613-2 method. Then, the instantaneous environmental noise at a receiver due to a moving high-speed train considering convection effect is evaluated with the information on the propagation attenuations from the instantaneous train location to the receiver and the sound power levels and directivity of stationary point sources evaluated by German Schall 03 (2006). To demonstrate the validity of proposed method, simulated and measured time history of instantaneous noise for KTX-I and KTX-II on running are compared and the results show that the method can be utilized for the train noise source identification as well as the simulation of instantaneous environmental noise emitted by a high-speed train.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.11
• /
• pp.982-986
• /
• 2013

The noise emitted from construction machinery has long been a cause of environmental disputes, especially to the nearby residents. In 2008, the Ministry of Environment adopted the construction machinery noise labeling system to encourage the development of the low noise construction machinery. After the implementation of the noise labeling system of the construction machinery, the noise emitted from the construction machinery has been decreased over the six years. But, as the quality of life improves, a growing number of people desire more comfortable and quite living environment. Under the situation, new systems like the low noise labeling system are considered to encourage the development of the low noise construction machinery. In accordance with the low noise labeling system, the construction machinery satisfying the standard of low noise are qualified to attach the low noise label in front of the products. Thus, the product qualified the low noise certification will be incentivized by the choice of the consumer. In this paper, we have studied the necessity of the low noise labeling system for the construction machinery and the considerations to adopt the low noise labeling system of construction machinery. And we have studied appropriate criterion to judge the low noise construction machinery. The considerations studied in this paper will be helpful to adopt the low noise labeling system of construction machinery in the future.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.535-538
• /
• 2009

Auto Pilot is the system which move automatically the vessel through locating operation mode to automatic after entering operating course using a electronic chart or plotter. And water jet is the a propulsion system that make a power to push the vessel through spouting the accelerated water which is absolbed by the hole in the bottom of vessel. The water jet receive the effect of the depth of water lowly, it's acceletion efficiency is higher under high speed and have an advantage on vibrating and floating sound, so it's demand is increasing as new propulsion system. However, the signal systems of auto Pilot and water jet are defferant, we need the system to communicate between each system. We propose the interface system which communicate between Auto pilot and water jet efficiently in this journal.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.1108-1111
• /
• 2009

Auto Pilot is the system which move automatically the vessel through locating operation mode to automatic after entering operating course using a electronic chart or plotter. And water jet is the a propulsion system that make a power to push the vessel through spouting the accelerated water which is absorbed by the hole in the bottom of vessel. The water jet receive the effect of the depth of water lowly, it's acceleration efficiency is higher under high speed and have an advantage on vibrating and floating sound, so it's demand is increasing as new propulsion system. However, the signal systems of auto pilot and water jet are different, we need the system to interface between each system. We designed the interface that efficiently digital feed back control embedded module between auto pilot and water jet system in this paper.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1068-1072
• /
• 2018

In underwater communications, there are many challenges due to energy limitations, long propagation delay, low data rate, and high power loss, unlike terrestrial RF communications. Especially, the propagation delay of underwater acoustic channel is five orders of magnitude higher than in electro-magnetic terrestrial channels due to the low speed of sound(1,500m/s). Thus, the MAC protocols for terrestrial communications are not suitable for underwater network. In this paper, we studied the considerations for MAC protocol in underwater acoustic channel. Here, we concentrated on CSMA based MAC protocols. From the results, we confirmed that the number of control packets has an important effect on the performance in underwater environment. These results would be useful in designing MAC protocols for underwater acoustic communications.