• 열처리공학회지
• /
• 제31권5호
• /
• pp.213-219
• /
• 2018

This study was carried out to investigate the effect of hot forging ratio and solution treatment temperature on the mechanical properties of incoloy 825 alloy. With an increasing of the hot forging ratio, grain size and range of grain size was decreased. With an increasing of the solution treatment temperature after 90% forging, grain size and range of grain size was increased. Cr carbides and Ti nitrides was precipitated at below $900^{\circ}C$ and volume fraction of precipitate was increased with an decreasing of the solution treatment temperature. With an increasing of the hot forging ratio, hardness, tensile strength and elongation, toughness was increased. With an increasing of the solution treatment temperature after 90% forging, hardness and strength was increased, elongation and toughness was decreased by grain refinement. With an increasing of the forging ratio, effect of solution treatment temperature on the hardness, strength and elongation was small, but on the toughness was large.

• 열처리공학회지
• /
• 제11권1호
• /
• pp.1-9
• /
• 1998

The objective of this study is to investigate the effect of solution-treatment temperature on the microstructure and damping capacity of a martensitic Fe-7%Ni-0.4%C alloy. The size of lath increased from $0.3{\mu}m$ to $0.55{\mu}m$ with increasing the solution-treatment temperature from 700 to $1100^{\circ}C$. In addition, the size of block, packet, and austenite grain had tendency to increase with increasing solution-treatment temperature. The damping capacity of the Fe-7%Ni-0.4%C martensitic alloy decreased with increasing the solution treatment temperature. The reason is not attributed to the increase in the size of lath, block, packet, and austenite grain, but to the increase in vacancy concentration which hinders dislocation motion.

• 한국산업융합학회 논문집
• /
• 제24권3호
• /
• pp.261-269
• /
• 2021

This study was evaluated the elastic wave properties according to tension of Incoloy 825 alloy with different solution treatment temperature and aging time. Solution treatment was carried out at 700, 800, 900, and 1000 ℃ for 1 hour, and aging was carried out at 700 ℃ for 1, 5, 10, and 30 hours. As the solution treatment temperature increased, the tensile strength decreased and the elongation increased. However, as the aging time increased, the tensile strength increased and the elongation decreased. The dominant frequency decreased as the solution treatment temperature increased, but increased as the aging time increased. The dominant frequency according to the solution treatment and aging time increased as the tensile strength increased, but increased despite the decrease in elongation.

• 열처리공학회지
• /
• 제4권1호
• /
• pp.37-41
• /
• 1991

In this study, the effect of solution treatment temperature on the tensile property in intermediate thermo-mechanical treated Al-Li alloys are investigated. After the intermediate thermo-mechanical treated Al-Li, Al-Li-Mg and Al-Li-Mg-Zr alloys were solution treated at various temperatures (500, 520 and $540^{\circ}C$), these were aged at $190^{\circ}C$, $240^{\circ}C$ and tested tensile properties. The results obtained from the experiment are as follows ; 1) The optimum solution heat-treatment temperature is $540^{\circ}C$ for a Al-Li alloy, and the recrystallized grain size is about $70{\mu}m$. 2) The optimum solution heat-treatment temperature is $500^{\circ}C$ for a Al-Li-Mg alloy, and the recrystallized grain size is the most coarse in all alloys. 3) The tensile property is independent of the solution treatment temperature in a Al-Li-Mg-Zr alloy, and the recrystallized grain size is the finest owing to addition of Zr.

• 열처리공학회지
• /
• 제33권6호
• /
• pp.277-283
• /
• 2020

Cu-Co-Si based alloy has a strengthening mechanism for Co₂Si intermetallic compounds deposited on the copper matrix after aging treatment and the solution treatment has a key influence on the strength and electrical conductivity of the final products. In this paper, the Cu-1.6%Co-0.38%Si alloy was fixed at the time and the solution treatment temperature was set at a temperature in the range of 800 to 950℃, and the change in mechanical properties was observed by fixing the temperature at 950℃ and changing the time. The microstructure was observed using an electron microscope and an optical microscope, and the changes in hardness, electrical conductivity, and bending workability after aging treatment were investigated. When the solution treatment time is less than 20 seconds, the solution treatment is not sufficient and the formation of precipitates contributing to the increase in hardness decreases and the hardness decreases after the aging treatment, and in more than 50 seconds, the hardness decreases due to the coarsening of the grains and the bending workability got worse.

• 열처리공학회지
• /
• 제30권3호
• /
• pp.99-105
• /
• 2017

This study was carried out to investigate the effect of heat treatment on the microstructure and mechanical properties in 90% hot forged Incoloy 825 alloy. With increasing solution treatment temperature, the grain size increased and the volume fraction of total precipitates decreased, and the precipitates disappeared at $1,000^{\circ}C$. With increasing aging time at $700^{\circ}C$, the volume fraction of precipitate increased and the precipitates size increased. Most of the precipitates consist $Cr_{23}C_6$ carbide, and a small amount of TiC carbide was also observed. With decreasing solution treatment temperature and increasing aging time, tensile strength and hardness increased, and the elongation and impact value decreased. With increasing aging time, the impact value decreased sharply by the increased of the precipitate size.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권1호
• /
• pp.98-106
• /
• 2005

The chemical conversion film formed on magnesium alloy was investigated by using the colloidal silica with some parameters such as solution pH. temperature, solution conditions, and treatment time. Moreover. the solutions consisted of colloidal silica titanium sulfate, and cobalt ions were used for the colloidal silica film to having a good corrosion resistance and adhesion properties. It was thought that the film at 298K was made with combination of Si-O. The quantity of film formed at high temperature such as 333K and 353K is smaller than dissolved quantity during chemical conversion treatment. Adding $CoSO_4$ to the colloidal silica solution enhanced the adhesion force between the silica film and magnesium substrate, The optimum conditions for the chemical conversion treatment solution were PH 2.90 s treatment, and 298K.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.137-139
• /
• 2006

In order to establish the optimum hot forming temperature and solution heat treatment temperature for 25% chromium super duplex stainless steel weld, a commercial 25%Cr-10%Ni-4%Mo weld metal for super duplex stainless steel(UNS S32750) with different solution heat treatment conditions at $1100^{\circ}C,\;1050^{\circ}C,\;1025^{\circ}C\;and\;1000^{\circ}C$ for 1.5 hours has been investigated by means of optical metallography, and estimated mechanical properties. It is found that exposure to elevated temperatures at $1050^{\circ}C,\;1025^{\circ}C\;and\;1000^{\circ}C$ except $1100^{\circ}C$ brings partial decomposition of ferrite to austenite and sigma phase, which deteriorates their properties and heat treatment at $1100^{\circ}C$ shows acceptable mechanical properties.

• Journal of Welding and Joining
• /
• 제1권2호
• /
• pp.61-68
• /
• 1983

Austenitic stainless steel has been investigated widely for creep strength of heat resistant material and effects of grain sizes due to various solution treatment time under constant temperature. It was studied that effects of grain sizes subject to solution treatment temperature 1100.deg. C, 1125.deg. C, 1175.deg. C, 1250.deg C, and 1300.deg. C respectively on the creep strength, fracture behaviour and fractography of SUS 316 stainless steel. The experimental results obtained were as follows. 1. The optimum grain size for the maximum creep strength did not vary with creep testing temperatures and stress levels. 2. Among various grain sizes due to different solution treatment temperature, the optimum grain size for the creep strength was found 0.044mm. Also the size showed the minimum initial strain regardless creep temperature. 3. Garofalo's equation of creep rupture life was applied well to SUS 316 stainless steel. 4. The fractography of optimum size was ductile intergranular fracture of dimple type and showed along with the increase of grain size intergranular fracture of w type.

• Journal of Mechanical Science and Technology
• /
• 제18권12호
• /
• pp.2204-2208
• /
• 2004

Ti-8Ta-3Nb has been developed as a new biomaterial. The experimental specimens are as-cast and forged Ti-8Ta-3Nb alloys. Treatment in a solution, ranging from 760 to 960$^{\circ}C$ has carried out. The microstructural research has carried out after the solution treatment and the hardness was measured. The specific heat and the length variations of Ti-8Ta-3Nb were also measured. The optimum temperature for the solution heat treatment of Ti-8Ta-3Nb was found to be 880$^{\circ}C$. This was based on the mechanical properties and the volume fraction of ${\alpha}$ phase and their phases shown from the results of the solution heat treatment. From the results, the ${\beta}$ transition temperature of Ti-8Ta-3Nb was found to be between 860$^{\circ}C$ and 880$^{\circ}C$.