• 한국전산유체공학회:학술대회논문집
• /
• 2001.10a
• /
• pp.112-117
• /
• 2001

A numerical investigation is made of unsteady double-diffusive convection of a Boussinesq fluid in a rectangular cavity subject to time-periodic thermal excitations. The fluid is initially stratified between the top endwall of low solute concentration and the bottom endwall of high solute concentration. A time-dependent heat flux varying in a square wave fashion, is applied on one sidewall to induce buoyant convection. The influences of the imposed periodicity on double-diffusive convection are scrutinized. A special concern is on the occurrence of resonance that the fluctuations of flow and attendant heat and mass transfers are mostly amplified at certain eigenmodes of the fluid system. Numerical solutions are analyzed to illustrate the characteristic features of resonant convection.

• Journal of Biomedical Engineering Research
• /
• v.3 no.1
• /
• pp.3-8
• /
• 1982

Solute transfer in artificial kidney dialyzers was analyzed using Kedem-Katcha- Isky's description on membrane transport. Mass transfer coefficient, K was deduced from the diffusive clearance of commercial hemodialyzers. It can to seen that Kd increases with the increase of blood flow rate, which means that there is substantial resistance in the blood phase for solute transport. Total clearance was estimated with the Werynski's formula. The increase in total clearance due to ultrafiltration was most significant for middle molecules like vitamin Bla, however that for smaller molecules such as urea and creatinine was minimal.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.3
• /
• pp.247-257
• /
• 2001

In an effort to improve the dent resistance of exterior body panels at a reduced steel thickness, the bake hardenable steels added Ti or Nb with tensile strength of 35Kgf/$\textrm{mm}^2$ were investigated. The bake hardenability increased with the annealing temperature and solute carbon content. Bake hardening of 3 to 5Kgf/$\textrm{mm}^2$ was obtained in steels with a controlled solute carbon concentration range from 6 to 10ppm. The galvannealing temperature and time had little influence on the bake hardenability. The Fe-Zn alloying reaction of 35Kgf/$\textrm{mm}^2$ BH steel was remarkably retarded due to a 0.07%P addition. The optimum galvannealing temperatures of 35Kgf/$\textrm{mm}^2$ BH steel were ranged from 520 to 56$0^{\circ}C$ in view of the Fe content and powdering resistance. The cross-section and planar views of the galvannealed coatings to characterize morphology development were discussed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.9 no.1
• /
• pp.41-45
• /
• 1969

A major disadvantage of Dental cements is their solubility. So it is very important to measure the exact amount of solubility to select clinically suitable materials. The most common laboratory test for solubility is the measurement of disintegration in distilled water, as outlined in A.D.A. Specifications 8 and 9, In addition to the possible factors influencing the solubility, the experiments were all conducted in compliance with A.D.A. Specifications. The solubility of 2 Zinc Phosphate cements and 1 Silicate cement in time of dissolution, concentration of solute in dissolving medium, and type of dissolving medium were investigated. The following results were obtained. 1. Generally the materials were more soluble in organic acids than in distilled water. 2. The dissolution cements tends be minimized by tests utilizing prolonged storage in the same media. 3. In Acetic acid solution, Zinc Phosphate cements were more soluble than Silicate cement, and in Citric acid solution both were markedly more soluble. 4. Solubility was increased by continually presenting fresh liquid, unsaturated with solute, to the cement-water interface.

• Journal of Korea Foundry Society
• /
• v.18 no.3
• /
• pp.234-239
• /
• 1998

Unidirectional solidification of $Al-CuAl_2$ eutectic composites was studied under the condition of forced convection by vibration. It has been shown that thermal gradient for solid is different from that for liquid during solidification under force convection by vibration. With increase of vibration, mobility of liquid increases, but decreases with decreasing vibration. The rate of solidification is very high initially, and decreases suddenly. For further solidification, the rate of solidification decrceases slowly, and shows a L-type behavior. The mechanical vibration during solidification effects efficiently on nucleation, and induces a forced convection in liquid. By the forced convection, great thermal gradient of liquid interface between solid and liquid can be obtained. The amount of solute near the interface also decreases as solute distribution is improved by the forced convection.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.13 no.2
• /
• pp.123-140
• /
• 2009

The effect of a solute concentration difference on the osmotic transport of water through the semi-permeable membrane of a simple cell model is investigated. So far, most studies on osmotic phenomena are described by simple diffusion-type equations ignoring all fluid motion or described by Stokes flow. In our work, as the governing equations, we consider the coupled full Navier-Stokes equations which describe the fluid motion and the full transport equation that takes into account of convection and diffusion effects. A two dimensional finite difference model has been developed to simulate the velocity field, concentration field, and semi-permeable membrane movement. It is shown that the cell swells to regions of lower solute concentration due to the uneven water flux through the semi-permeable membrane. The simulation is applied on a red blood cell geometry and the relevant results are presented.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.09a
• /
• pp.307-311
• /
• 2004

The unsaturated zone is a significant pathway of the surface contaminant movement and is a highly heterogeneous medium. Therefore, there are limitations in applying conventional convection-dispersion equation(CDE). Artificial neural network(ANN) is considered to be a versatile tool for approximating complex functions. For evaluating the applicability of ANN, numerical tests using ANN were conducted with training set generated by HYDRUS-2D which is based on CDE. The results represent that ANN can estimate the solute transport and the choice of network parameters and generation of training set patterns are important for efficient estimation.

• Water for future
• /
• v.23 no.2
• /
• pp.213-225
• /
• 1990

A mathematical model is presented for predicting the steady state two-demensional distribution of solute concentration in the meandering nonuniform natural channel. The dispersion equation derived herein employs the transverse cumulative discharge as an independent variable replacing the transverse distance and that it is developed in an orthogonal curvilinear coordinnate system which follows the flow direction of natural channel. The prediction from the results of numerical model are compared with laboratory experiment data. It is found that results from simulation and experiments are in good agreement.

• Journal of Biomedical Engineering Research
• /
• v.5 no.1
• /
• pp.9-14
• /
• 1984

The asymptotic solution using the Tailor series has been given explicit form for the solute concentration and overall solute removal in hemodiafilter using one dimensional model. The numerical solutions have been calculated within 0.001% error by the Romberg integration method. Compared with the numerical solutions, the oneterm asymptotic solutions were found to be within 3% error for the condition > 3.0 and three-terms asymtotic solutions were required for the condition >0.7 where denotes measure of convection over diffusional transport and a the ratio of blood flow rate over dialysate flow rate.

• Applied Microscopy
• /
• v.44 no.3
• /
• pp.105-109
• /
• 2014

The microstructure of as-quenched $Al_{70}Cu_{18}Mg_{12}$ alloy has been investigated in detail using transmission electron microscopy. Al nano-crystals about 5 nm with a high density are distributed in the amorphous matrix, indicating amorphous matrix nano-composite can be synthesized in Al-Cu-Mg alloy. The high density of Al nano-crystals indicates very high nucleation rate and sluggish growth rate during crystallization possibly due to limited diffusion rate of solute atoms of Cu and Mg during solute partitioning. The result of hardness measurement shows that the mechanical properties can be improved by designing a nano-composite structure where nanometer scale crystals are embedded in the amorphous matrix.