• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1999년도 추계학술발표강연 및 논문개요집
• /
• pp.55-55
• /
• 1999

• 한국세라믹학회지
• /
• 제40권4호
• /
• pp.393-397
• /
• 2003

To investigate the effect of AIN c-axis orientation on the resonance performance of film bulk acoustic wave resonators, solidly mounted resonators with crybtallographically different AIN piezoelectric films were prepared by changing only the bottom electrode surface conditions. As increasing the degree of c-axis texturing, the effective electromechanical coupling coefficient ($\kappa$$\_$eff/)$^2$ in resonators increased gradually. The least 4 degree of full width at half maximum in an AIN(002) rocking curve, which corresponds to $\kappa$$^2$$\_$eff/ of above 5%, was measured to be necessary for band pass filter applications in wireless communication system. The longitudinal acoustic wave velocity of AIN films varied with the degree of c-axis texturing. The velocity of highly c-axis textured AIN film was extracted to be about 10200 n/s by mathematical analysis using Matlab.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2003년도 제24회 학술발표회 초록집
• /
• pp.123-123
• /
• 2003

• Journal of information and communication convergence engineering
• /
• 제3권4호
• /
• pp.167-171
• /
• 2005

In this paper, the resonance characteristics of SMR-type FBAR devices annealed by three different annealing methods are investigated and compared. The resonance characteristics could be effectively improved by the proposed efficient annealing method which optimizes the annealing conditions. It seems very useful for improving the performance of the SMR-type FBAR devices as a cost-effective way.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 추계종합학술대회
• /
• pp.630-632
• /
• 2003

본 논문에서는 Ladder 형과 SCF 형의 구조를 가지는 FBAR 필터의 제작에 대해 발표한다. 단위공진기의 구조는 W/SiO$_2$, 반사층을 갖는 SMR (Solidly Mounted Resonate.) 구조을 가지며, 21,200$\mu$m$^2$의 공진 면적을 갖는 단위공진기의 $K^2$eff, Q$_{s}$ 그리고 Q$_{p}$는 각각 3.24%, 6,363 그리고 6,749의 값을 보였다. 이와같은 성능을 갖는 단위공진기를 기본으로 제작된 필터의 크기는 Ladder 형이 800$\times$2000($\mu\textrm{m}$$^2$)의 크기를 갖고 SCF 형이 600$\times$500($\mu\textrm{m}$$^2$)을 가진다. 먼저 필터의 기본이 되는 박막형 공진기를 최적화시키고, 이를 바탕으로 Ladder 형과 SCF형의 구조를 가지는 FBAR 필터를 제작하여 성능을 비교하였다.다..

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2005년도 추계종합학술대회
• /
• pp.320-324
• /
• 2005

In this paper, the resonance characteristics of SMR-type FBAR devices annealed by three different annealing methods are investigated and compared. The resonance characteristics could be effectively improved by the proposed efficient annealing method which can optimize the annealing conditions. It seems very useful for improving the performance of the SMR-type FBAR devices in a cost-effective way.

• 한국전기전자재료학회논문지
• /
• 제18권2호
• /
• pp.159-163
• /
• 2005

This paper gives characterization of ZnO thin film deposited by RF magnetron sputtering method, which is concerned in deposition process and device fabrication process, to fabricate solidly mounted resonator(SMR)-type film bulk acoustic resonator(FBAR). A piezoelectric layer of 1.1${\mu}{\textrm}{m}$ thick ZnO thin films were grown on thermally oxidized SiO$_2$(3000 $\AA$)/Si substrate layers by RF magnetron sputtering at the room temperature. The highly c-axis oriented ZnO thin film was obtained at the conditions of 265 W of RF power, 10 mtorr of working pressure, and 50/50 of Ar/O$_2$ gas ratio. The piezoelectric-active area was 50 ${\mu}{\textrm}{m}$${\times}$50${\mu}{\textrm}{m}$, and the thickness of ZnO film and Al-3 % Cu electrode were 1.4 ${\mu}{\textrm}{m}$ and 180${\mu}{\textrm}{m}$, respectively. Its series and parallel frequencies appeared at 2.128 and 2.151 GHz, respectively, and the qualify factor of the resonator was as high as 401.8$\pm$8.5.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권7호
• /
• pp.308-314
• /
• 2005

The 2 GHz film bulk acoustic wave resonator(FBAR), one of the most necessary device of the next generation mobile communication system, consisted of solidly mounted resonator(SMR) structure using Brags reflector, was researched in this paper The FBAR applied SiO$_{2}$ and W had large difference of the acoustic impedance to reflector Al to electrode and ZnO to piezoelectric layer. Specially, the FBAR applied the two-step deposition method to improve the c-axis orientation and increase reproducibility of the fabrication device had good performance. The electrical properties of plasma such as impedance, resistance, reactance, $V_{pp},\;I{pp}$, VSWR and phase difference of voltage and current, was analyzed and measured by RF sensor with the variable experiment process factors such as gas ratio, RF power and base vacuum level about concerning the thickness, c-axis orientation, adhesion and roughness. The FBAR device about the optimum condition resulted reflection loss(S$_{11}$) of -17 dB, resonance frequency of 1.93 GHz, electric-mechanical coefficient(k$_{eff}$) of 2.38 $\%$ and Qualify factor of 580. It was seen better qualify than the common dielectric filter at present and expected on business to the filter device of 2 GHz bandwidth with the MMIC technology.

• 한국전기전자재료학회논문지
• /
• 제18권2호
• /
• pp.164-168
• /
• 2005

Piezoelectric ZnO thin films were for the first time formed on SiO$_2$/Si(100) substrate using 2-step deposition, atomic layer deposition(ALD) and RF magnetron sputtering deposition, for film bulk acoustic resonator(FBAR) applications. The ZnO buffer layer by ALD was deposited using alternating diethyl zinc(DEZn)/$H_2O$ exposures and ultrahigh purity argon gas for purging. The ZnO films by 2-step deposition revealed stronger c-axis-preferred orientation and smoother surface than those by the conventional RF sputtering method. The solidly mounted resonator(SMR)-typed FBAR fabricated by using 2-step deposition method revealed higher quality factor of 580 and lower return loss of -17.35dB. Therefore the 2-step deposition method in this study could be applied to the FBAR device fabrication.

• 한국재료학회지
• /
• 제9권12호
• /
• pp.1263-1269
• /
• 1999

본 실험에서는 반사층(reflector)을 이용한 FBAR (Film Bulk Acoustic Resonator) 즉, SMR (Solidly Mounted Resonator) 제조에 필요한 재료들의 최적 증착 조건을 설정하여, 이를 바탕으로 제조한 SMR의 특성을 보여주었다. SMR은 상하부 전극층, 압전 박막층, 반사층, 기판으로 구성된다. 상하부 전극으로 알루미늄(Al) 금속 박막을 사용하였고 압전 박막층으로 산화아연(ZnO) 박막을 사용하였다. 실리콘(Si) 기판과 하부 전극 사이에 위치하는 반사층은 5층의 이산화규소 ($Si_2$)와 텅스텐(W) 박막으로 구성되었다. 상하부 전극은 dc 스퍼터링 방법으로 증착아였으며 반사층과 압전 박막층은 rf 스퍼터링 방법으로 증착하였다. 최적 증착 조건에서 증착된 산화아연 (ZnO) 박막은 rocking curve에서 표준편차가 $2.17^{\circ}$의 우수한 c축 우선배향성, 비저항은 $10^4\;{\Omega}cm$이상, 막 표면 거칠기(rms roughness)는 10.6${\AA}$의 특성을 나타내었다. 최적 증착 조건에서 증착된 텅스텐(W)과 이산화규소($Si_2$) 박막의 특성은 박막 거칠기 (rms roughness)가 각각 16 ${\AA}$, 33 ${\AA}$을 나타내었다. 또한 증착된 알루미늄 금속 박막의 비저항은 $5.1{\times}10^{-6}\;{\Omega}cm$이었다. 반도체 기본 공정을 이용하여 면적 $250{\times}250\;{\mu}m^2$의 SMR 소자를 만들고, 네트웍 분석기로 SMR 소자의 공진 특성을 분석하였다. 공진특성은 1.244 GHz에서 직렬공진, 1.251 GHz에서 병렬공진을 나타내었다. SMR 소자의 공진특성에서 공진기의 Q값은 1200이었다.