• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.825-826
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1287-1288
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1285-1286
• /
• 2013

• Journal of Korean Society for Atmospheric Environment
• /
• 제19권E1호
• /
• pp.21-28
• /
• 2003

An auxiliary device, called Post Cyclone (PoC). had been introduced and primarily examined in earlier works which proved the reduction of the emission of fine dust from the gas-solid cyclones without incurring significant increase of cost and pressure drop. It has been known that the PoC has some advantages over other secondary dust treatment devices such as (a) simple design, (b) low cost of manufacture, (c) minimum additional pressure drop, (d) high recoverbility of the product dust, and (e) simplicity of operation. Despite the potential advantage, however, lack of practical data confined its plausible application in wide areas. Thus, in this work, a few serial experiments were conducted in terms of a few operation conditions, and the particle trajectories throughout the cyclone set-up were visually analyzed by using a commercial computer simulation program (FLUENT).

• 한국정밀공학회지
• /
• 제21권1호
• /
• pp.32-39
• /
• 2004

Traditional forging of a hollow T-shaped part has been applied to forge a solid T-shaped product from a solid billet and then to machine the hollow in that. In a case, a hollow T-shaped part can be forged by backward-extruding from a solid billet. In this study, four types of forging were suggested for manufacture of hollow T-shaped parts. Forging simulations for each of these forging methods were carried out to investigate folding defect, metal flow pattern, effective strain, and forging loads. Experimental works were carried out to be compared with the simulation results. Here, the ratio of the thickness of the hollow tube to that of the flange was selected to investigate a forging defect like folding.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.458-463
• /
• 1999

When designing a gerotor, designers determine basic dimensions of a gerotor with transmitted power considering strength, interference and so on. But, designers can not easily obtain the tooth profile generated by dimensions as well as the geometry of generating hob for cutting the tooth profile. In order to resolve these problems, an automatic design system creating not only the solid model of a gerotor but also that of the generating hob using the design parameters of dimensions is developed. Through the developed system, designers can improve the efficiency of design and satisfy the variable requirements of design as well. In this research, the three-dimensional solid model of gerotor is generated considering the design parameters. Besides, that of generating hob with respect to the design parameters of hob is created automatically. The system is developed using Visual Basic and its three-dimensional geometric modeling module is constructed using SolidWorks.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.54.2-54.2
• /
• 2012

Solid-state dewetting of thin films is a process through which continuous solid films decay to form islands. Dewetting of thin films has long been a critical issue in microelectronics and much effort has been made to prevent the process and enhance the stability of films. On the other hand, dewetting has also been purposely induced to create arrays of particles and other structures for applications, including plasmonic structures and catalysts for growing nanotube and nanowire. We have investigated ways of producing regular structures via templated dewetting of thin films. Mainly, two different approaches have been used in our works to template dewetting of thin films: periodic topographical templating and planar patterning of epitaxially-grown films. Dewetting of topographically-patterned thin films results in the formation of nanoparticle arrays with spatial and crystallographic orders. Morphological evolution during templated-dewetting of single crystal films occurs in deterministic ways because of geometric and crystallographic constraints, and leads to the formation of regular structures with smaller sizes and more complex shapes than the initial patches. These results will be reviewed in this presentation.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2003년도 추계학술대회 발표 논문집
• /
• pp.207-211
• /
• 2003

In this study, the geometric modeling has been conducted for a new model of 12 inch hot-cold chuck using three-dimensional solid modeler, SolidWorks. Then, the heat transfer analysis and the thermal deformation analysis using FEM have been performed. The results of the analysis show the temperature distribution and the deformed shape of a new model of 12 inch hot-cold chuck. The evaluation for the surface flatness of a new model has been performed based on the deformed shape obtained from ANSYS.

• 한국생산제조학회지
• /
• 제23권1호
• /
• pp.87-93
• /
• 2014

This paper provides a methodology for extracting design data from the three-dimensional design software SolidWorks$^{(R)}$, which is based on the existing trochoid pump design equations that are used by hydraulic field engineers. The data extracted from the SolidWorks$^{(R)}$ model are input to a hydraulic analysis software AMESim model to determine the design factors that can influence the properties of a trochoid pump. On the basis of the simulation results, this paper proposes a method to reduce the flow loss by adjusting the outlet angle of the trochoid pump. This proposal was verified by using actual experimental results, which confirmed that adjusting the outlet angle can increase the flow rate. Hence, the results presented in this paper can contribute to the prototyping of a trochoid pump by reducing the cost associated with a trial-and-error design.

• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.465-471
• /
• 2013

Flow rate control is the uppermost concern for a trochoid hydraulic pump. Cavitation within the flow field of the pump has the greatest effect on the flow control during high-speed pump rotation of approximately 3500~4000 RPM. In this paper, based on AMESim$^{(R)}$ and Solid Works$^{(R)}$, we will present a method to simulate cavitation by analyzing the control factors of a trochoid pump, including the hydraulic pressure change at the outlet, flow rate based on the rotation speed of the inner rotor, leakage through the gap between the outer and inner rotors, and discharging angle of the outlet. The proposed methodology of the [cavitation simulation will enable field engineers to more easily design trochoid pumps, and will allow more concrete control over the flow rate of the pump by realizing an analysis model similar to the actual product model.