• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.16-23
• /
• 2001

Spray dispersion in high pressure diesel engines have been simulated experimentally with a special emphasis on the effect of swirl by using a liquid injection technique. A constant volume chamber was designed to be rotatable in order to generate a continuous swirl and to have the flow field closely resembling a solid body rotation. Emulsified fuel was injected into the chamber and the developing process of fuel sprays was visualized. The effect of swirl on the spray dispersion was quantified by calculating non-dimensionalized dispersion area according to the spray tip penetration length. The results show that the effect of swirl on the spray dispersion is different between short and long spray penetrations. For short range of spray tip penetration, the effect of swirl on spray dispersion is quite small. However, as the spray tip is penetrated into longer distance in spray chamber, the effect of swirl on spray dispersion becomes larger. These results can be used as a basic data for designing combustion chamber and injection system of direct injection diesel engine.

• Fibers and Polymers
• /
• v.2 no.4
• /
• pp.203-211
• /
• 2001

Residual stresses were predicted by a flow analysis in the mold cavity and residual stress distribution in the injection molded product was measured. Flow field was analyzed by the hybrid FEM/FDM method, using the Hele Shaw approximation. The Modified Cross model was used to determine the dependence of the viscosity on the temperature and the shear rate. The specific volume of the polymer melt which varies with the pressure and temperature fields was calculated by the Tait\`s state equation. Flow analysis results such as pressure, temperature, and the location of the liquid-solid interface were used as the input of the stress analysis. In order to calculate more accurate gap-wise temperature field, a coordinate transformation technique was used. The residual stress distribution in the gap-wise temperature field, a coordinate transformation technique was used. The residual stress distribution in the gap-wise direction was predicted in two cases, the free quenching, under the assumption that the shrinkage of the injection molded product occurs within the mold cavity and that the solid polymer is elastic. Effects of the initial flow rate, packing pressure, and mold temperature on the residual stress distribution was discussed. Experimental results were also obtained by the layer removal method for molded polypropylene.

• Korea-Australia Rheology Journal
• /
• v.16 no.4
• /
• pp.163-168
• /
• 2004

In this study, an ultrasonic technique was employed to obtain pressure-volume-temperature (PVT) rela­tionship of polymer melt by measuring ultrasonic velocities under various temperatures and pressures. The proposed technique was applied to on-line monitoring of injection molding process as an attempt to predict quality of molded parts. From the comparison based on Tait equation, it was confirmed that the PVT behav­ior of a polymer is well described by the variation of ultrasonic velocities measured within the polymer medium. In addition, the changes in part weight and moduli were successfully predicted by combining the data collected from ultrasonic technique and artificial neural network algorithm. The results found from this study suggest that the proposed technique can be effectively utilized to monitor the evolution of solid­ification within the mold by measuring ultrasonic responses of various polymers during injection molding process. Such data are expected to provide a critical basis for the accurate prediction of final performance of molded parts.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.299-302
• /
• 2011

In the supersonic jet of a solid rocket motor, various noise is investigated. The purpose of this study is to attain and evaluating a design and manufacturing technique of the SRM noise reduction. In this study, the water is injected into the supersonic jet of the SRM to reduce the noise. Furthermore, the diffuser and stack are installed to suppress the SRM noise. Through the SRM ground tests, the noise is reduced approximately 20dBA with application of the diffuser/stack with water injection.

• Nuclear Engineering and Technology
• /
• v.51 no.7
• /
• pp.1866-1870
• /
• 2019

Residual salt separation is an essential step in pyroprocessing because its reaction products, as prepared by electrochemical unit processes, contain frozen residual electrolyte species, which are generally composed of alkali-metal chloride salts (e.g., LiCl, KCl). In this study, a simple technique that utilizes high-temperature gas flux as a driving force to melt and push out the residual salt in the reaction products was developed. This technique is simple as it only requires the use of a heating gun in combination with a gas injection system. Consequently, $LiNO_3-ZrO_2$ and $LiCl-ZrO_2$ mixtures were successfully separated by the high-temperature gas injection (separation efficiency > 93%), thereby demonstrating the viability of this simple technique for residual salt separation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.137-146
• /
• 1997

Spray characteristics of high pressure injectors for diesel engines have been experimentally studied with special emphasis on the effect of swirl. A constant volume chamber was rotated in order to generate a continuous swirl having the flow field of a solid body rotation, resulting in the linear dependance of the swirl number on the rotating speed of the chamber. Emulsified fuel is injected into the chamber and the developing process of fuel sprays is visualized. The fuel spray developing process in D.I. diesel engine was investigated by this liquid injection technique. The effect of swirl on the spray tip penetration is quantified through modelling. Results show that the spray tip penetration is qualitatively different for low and high pressure injections. For high pressure injection case, a good agreement is achieved between the experimental results and the modeling accounting the effect of swirl. For low pressure injection, a reasonable agreement is obtained. It is found that excessive swirl may cause adverse effect on spray dispersion during the initial combustion period since the spray can not be impinged on chamber wall.

• Archives of Plastic Surgery
• /
• v.38 no.2
• /
• pp.166-172
• /
• 2011

Purpose: Facial contouring surgery for improving congenital, acquired deformity and senile change were attempt in past. Recently contouring surgery became more interested subject for improving the flat forehead and temple area. Many synthetic materials were used such as Collagen, silicon, polyacrylamide gel as liquid form and Gore-tex, silicon implant, endotine as solid form. But, these synthetic implants associate complications as foreign body reaction, infection, displacement, granuloma formation and absorption. Auto-fat injection are used for disfigurement of many part of body. We did auto-fat injection for facial contouring of forehead and temple region. Auto-fat injection is suitable without foreign body reaction, displacement, and toxic reaction. Also auto-fat is relatively simple to obtain from patient and less expensive and able to repeat surgeries. Methods: From 2006 to 2009, 150 patients were treated with Auto-fat injection for facial contouring. For follow up, we sent questionnaire to all patients but 110 patients returned answer sheets. The patients consisted of 20 male patients and 90 female patients with an age ranged from 26 to 60, and the mean 43. Fat tissue were injected 6-8 cc in forehead, 7-12 cc in temple area and fat were harvested from thigh and abdomen. Results: In follow up, all patients, showed absorption of injected fat varied degree and except two patients all patients underwent secondary fat injection. Complications were minimal and neuropraxia of facial nerve were recovered. Most of the patients were satisfied with result of procedure, and answered that they recommend same procedure to their friends and will do surgery again. Conclusion: Auto-fat injections were implemented for facial contouring in 150 patients and obtained satisfactory result. Auto-fat injection is relatively easy procedure and applicable widely. Even though, by passing time, some of the injected fats are absorbed, auto-fat injection could be choice of treatment for contouring forehead and temple. With accumulations of cases and development of surgical technique, better result could be expected.

• Journal of Environmental Science International
• /
• v.15 no.1
• /
• pp.77-84
• /
• 2006

An effective technique of sludge separation is required for excess sludge of sewage or wastewater plant. The separation of bulking sludge of paper manufacturing plant was studied using DAF(Dissolved Air Flotation) system. The effects of parameters such as nozzle type, A/S(air/solid) ratio. pressure, injection time of pressured water and saturation time were examined. The results showed that the best nozzle type was flat which had small orifice hole, The optimum A/S ratio and pressure were $7.070\times10^{-3}$(recycle ratio of pressured water $20\%$) and 5atm, respectively. Injection times of pressurized water around 20-25 sesc and flotation time of 30 min appeared to be optimal for the DAF operation. The order of performance of packing was 18 mm > 22 mm > 32 mm.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.11
• /
• pp.3223-3226
• /
• 2013

Spherical phospholipid-bilayers, vesicles, were prepared using the layer-by-layer double emulsion technique, which allows the bilayer to be formed asymmetrically. On the outer layer of the vesicles, the phospholipase D (PLD) reacted to convert phosphatidylcholine (PC) to phosphatidic acid (PA). The reaction induced the curvature change of the vesicles, which eventually led to rupture. The response time from the time of PLD injection to the time of rupture was measured against different vesicle curvatures and the outer layer phase, using the fluorescence intensity change of a pH-sensitive dye encapsulated within the vesicles. The effect of the vesicle curvature on the response was observed to be more significantly dramatic at the solid phase, compared to the liquid phase. Furthermore, in the solid phase, the response time was faster for 80 and 155 nm vesicles and, slower for 605 nm vesicles than similarly sized vesicles in the liquid phase vesicles. This difference in the response time was thought to result from the configuration determined by the phase difference and the PLD behavior.

• The Korean Journal of Pain
• /
• v.23 no.2
• /
• pp.137-141
• /
• 2010

Background: Facet joint have been implicated as a source of chronic low back pain. Radiofrequency denervation has demonstrated the most solid evidence. To increase safety and efficacy of treatment, computed tomography (CT) guidance injection has been used in several disease. The purpose of this study was to evaluate the efficacy of CT-guided radiofrequency rhizotomy in the treatment of facet joint pain. Methods: A total of 40 patients were randomized to undergo radiofrequency facet joint denervation under CT guidance or C-arm guidance. All patients were examined visual analogue scale (VAS) score before treatment, 1 month, and 3 months after treatment. Results: The VAS in both groups showed significant improvement over the 1-month interval. No significant difference in the VAS score among the group was observed. Conclusions: In this study there was no significant difference between CT guidance lumbar rhizotomy and C-arm guidance lumbar rhizotomy. Therefore CT-guided radiofrequency denervation of the lumbar facet joint was a minimally invasive technique that appears effective.