• Analytical Science and Technology
• /
• v.37 no.1
• /
• pp.47-62
• /
• 2024

Abu Gurdi area is located in the South-eastern Desert of Egypt which considered as volcanic massive sulfide deposits (VMS). The present work aims at investigating the ore mineralogy of Abu Gurdi region in addition to the effectiveness of the hydrometallurgical route for processing these ores using alkaline leaching for the extraction of Zn, Cu, and Pb in the presence of hydrogen peroxide, has been investigated. The factors affecting the efficiency of the alkaline leaching of the used ore including the reagent composition, reagent concentration, leaching temperature, leaching time, and Solid /Liquid ratio, have been investigated. It was noted that the sulfide mineralization consists mainly of chalcopyrite, sphalerite, pyrite, galena and bornite. Gold is detected as rare, disseminated crystals within the gangue minerals. Under supergene conditions, secondary copper minerals (covellite, malachite, chrysocolla and atacamite) were formed. The maximum dissolution efficiencies of Cu, Zn, and Pb at the optimum leaching conditions i.e., 250 g/L NaCO₃ - NaHCO₃ alkali concentration, for 3 hr., at 250 ℃, and 1/5 Solid/liquid (S/L) ratio, were 99.48 %, 96.70 % and 99.11 %, respectively. An apparent activation energy for Zn, Cu and Pb dissolution were 21.599, 21.779 and 23.761 kJ.mol^-1, respectively, which were between those of a typical diffusion-controlled process and a chemical reaction-controlled process. Hence, the diffusion of the solid product layer contributed more than the chemical reaction to control the rate of the leaching process. High pure Cu(OH)₂, Pb(OH)₂, and ZnCl₂ were obtained from the finally obtained leach liquor at the optimum leaching conditions by precipitation at different pH. Finally, highly pure Au metal was separated from the mineralized massive sulfide via using adsorption method.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.406-415
• /
• 2018

Here, as-synthesized $Fe_3O_4$ nanoparticles were incorporated into the zeolitic imidazolate framework (ZIF-8) lattice to activate sodium percarbonate (SPC) for degradation of methylene blue (MB). The reaction rate constant of $Fe_3O_4@ZIF-8/SPC$ process ($0.0632min^{-1}$) at acidic conditions (pH = 3) was more than six times that of the $Fe_3O_4/SPC$ system ($0.009min^{-1}$). Decreasing the solute concentration, along with increasing SPC concentration and $Fe_3O_4@ZIF-8$ nanocomposite (NC) dosage, favored the catalytic degradation of MB. The $Fe_3O_4@ZIF-8$ NC after fifteen consecutive treatment processes showed the excellent stability with a negligible drop in the efficiency of the system (<10%). The reaction pathway was obtained via GC-MS analysis.

• Journal of Environmental Science International
• /
• v.19 no.3
• /
• pp.379-387
• /
• 2010

Sediments of Little Scioto (LS) River in Ohio was contaminated by poor disposal of creosote from Baker Wood Creosoting Facility. Among the primary compounds of creosote, Polycyclic Aromatic Hydrocarbons (PAHs) are the most common ingredient PAHs are known for toxic, carcinogenic and mutagenic compounds. There are many difficulties to remove the PAHs in nature environment because their characteristics are having a less water-solubility, volatile and low mobility properties as increasing the molecular weight. The generation of hydroxyl radicals (${\cdot}OH$) and hydrogen peroxide ($H_2O_2$) forms as well as high temperature (5000 K) and pressure (1000 atm) by a physico-chemical effects of ultrasound during a cavitation collapse can promote the degradation and desorption of PAHs in sediment And it can also produces shock wave and microjets which are able to change the size and surface of particle in solid-liquid system as one of physical effects. Therefore, we explored to understand the role of particle size, the effect of elimination for PAHs concentration by ultrasound and optimize the conditions for ultrasonic treatment. The condition of various size of particles (> $150{\mu}m$, < $150{\mu}m$) and solid-liquid ratio (12.5g/L, 25g/L) for the treatment was considered and ultrasonic power (430 W/L) with liquid - hexane extraction and microwave extraction method were applied after ultrasound treatment.

• Journal of Marine Life Science
• /
• v.2 no.2
• /
• pp.49-55
• /
• 2017

Four chemical treatments with hydrogen peroxide (H₂O₂), copper sulfate (CuSO₄), potassium permanganate (KMnO₄) and chlorine (Cl₂) were applied to the effluent pond water of a hybrid striped bass saltwater recirculating aquaculture system to compare their oxidation power. Four chemicals were applied at concentrations of 0 (control), 1, 5, 10 and 20 mg/l. An additional concentration of 40 mg/l was included in the chlorine treatment. Water samples from four hybrid striped bass ponds were tested with KMnO₄ and Cl₂. H₂O₂ did not reduce any of BOD, COD and chlorophyll-a, and copper sulfate was only effective on chlorophyll-a for the effluent pond. Removal efficiencies for chlorophyll-a by copper sulfate were 19.2%, 37.5%, 54.2% and 74.1% dose-dependently. Potassium permanganate effectively removed the BOD, COD and chlorophyll-a. The COD removal rates in four fish ponds varied from 15.9% to 31.6% at the concentration of 10 mg/l. Interestingly, Cl₂ did not reduce the BOD and COD at all, but the BOD and COD instead increased drastically with increasing the Cl₂ concentration. The pond water with the highest initial BOD and COD values among the fish ponds tested increased by 350% in the BOD and 150% in the COD at 20 mg/l. Furthermore, Cl₂ did not significantly reduce any types of solid matter in this study, while KMnO₄ seemed to reduce some extent volatile dissolved solid in the fish pond.

• Nuclear Engineering and Technology
• /
• v.55 no.5
• /
• pp.1644-1650
• /
• 2023

In spent fuel reprocessing, UO₂(DBP)₂ (U-DBP) can be deposited in stainless steel equipment. U-DBP must be removed by dissolution and the process must not cause corrosion to stainless steel. This study was conducted to find the best scheme for dissolution. U-DBP was manufactured by the titrimetric sedimentation method. The effects of different factors on the dissolution of U-DBP were investigated. For example, solid-liquid ratio, hydrazine carbonate solutions with different mass components, mixed solutions containing different concentrations of H₂O₂, and different carbonates. The results indicated that U-DBP does not have a regular crystal morphology. With the increase of the solid-liquid ratio and the mass fraction of hydrazine carbonate, the concentration of U(VI) at the dissolution equilibrium increases gradually. The addition of H₂O₂ has a great promotion effect on the dissolution. However, when the concentration of H₂O₂ is greater than 0.5 M, the dissolution solution may have an erosive effect on the stainless steel. (NH₄)₂CO₃ can increase the dissolution capacity of dissolved U-DBP, but it may also accelerate the corrosion of stainless steel.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.1
• /
• pp.1-8
• /
• 2009

This research was performed to assess a Fenton-like oxidation using naturally present iron in the field to treat remained oils throughout silty clay residues which finally resided even after a series of soil washing process. Biodegradability was thus tested for reaction products to investigate a possible treatment of the Fenton-like oxidation coupled with a biological treatment process. For those purposes, two types of field soil samples (e.g., dewatered cake after conditioning with a polymer and not-dewatered residue) were tested to remove TPH by adding the various concentration of hydrogen peroxide ($H_2O_2$). Moreover the biodegradability of treated samples was observed based on the ratio of $BOD_5/COD_{Cr}$ after Fenton-like oxidation. The Highest removal of TPH was at 1% of hydrogen peroxide ($H_2O_2$) when hydrogen peroxide ($H_2O_2$) was continuously injected for a period of time rather than that of spot introduction with the same amount of it. For the dewatered cake, TPH was effectively treated when the ratio of solid and water was mixed at 1 : 2. Employing cooking oil could increase solubility of TPH due to enhanced surface-active escalating TPH desorption from silty clay. Nonetheless, the biodegradability was decreased as long as the oxidation duration being extended regardless of operational conditions. It was therefore proved that Fenton-like oxidation using $H_2O_2$ and natural iron minerals was able to remove adsorbed oils in silty clay but the removal efficiency of TPH was low. And if a biological treatment process followed after Fenton-like oxidation, microorganisms would need enough time for acclimation.

• Journal of the Mineralogical Society of Korea
• /
• v.29 no.3
• /
• pp.113-122
• /
• 2016

This study aims to improve the recovery of gold and silver by removing hematite from gold ore of an oxidation zone with ammonia solution. Quartz, hematite and muscovite were present in the oxidation zone, while hematite was hydrogenous. As a result of performing an ammonia leaching test on variables, it is found that the maximum Fe leaching parameter was $-45{\mu}m$ particle size, 1.0 M sulfuric acid concentration, 5.0 g/l ammonium sulfate concentration and 2.0 M hydrogen peroxide concentration. It is also confirmed that goethite was precipitated and formed from that ammonia elution. As the amount of Fe-removal was increased in a solid-residue, the recovery of Au and Ag were increased, too.

• Journal of the Mineralogical Society of Korea
• /
• v.26 no.3
• /
• pp.139-150
• /
• 2013

In order to effectively leach Fe from pyrite, the application of microwave energy and ammonia solution has been conducted. Pyrite transforms into hematite and pyrrhotite when treated with microwave radiation for 60 minutes, and in this time the highest amount of Fe was leached by the ammonia solution. Up to 99% of the Fe was leached when the experimental conditions were: 325-400 mesh particle size for the pyrite and 60 min. was the microwave exposure time. The ammonia leaching conditions were 0.3 M sulfuric acid, 2.0 M ammonium sulfate and 0.1 M hydrogen peroxide concentration. The pyrite, hematite, and pyrrhotite were not detected using XRD analysis from the solid-residues treated by the ammonia solution except for quartz.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.88.1-88.1
• /
• 2012

Silicon nanowires (SiNWs), due to their unusual quantum-confinement effects that lead to superior electrical and optical properties compared to those of the bulk silicon, have been widely researched as a potential building block in a variety of novel electronic devices. The conventional means for the synthesis of SiNWs has been the vapor-liquid-solid method using chemical vapor deposition; however, this method is time consuming, environmentally unfriendly, and do not support vertical growth. As an alternate, the electroless etching method has been proposed, which uses metal catalysts contained in aqueous hydrofluoric acids (HF) for vertically etching the bulk silicon substrate. This new method can support large-area growth in a short time, and vertically aligned SiNWs with high aspect ratio can be readily synthesized with excellent reproducibility. Nonetheless, there still are rooms for improvement such as the poor surface characteristics that lead to degradation in electrical performance, and non-uniformity of the diameter and shapes of the synthesized SiNWs. Here, we report a facile method of SiNWs synthesis having uniform sizes, diameters, and shapes, which may be other than just cylindrical shapes using a modified nanosphere lithography technique. The diameters of the polystyrene nanospheres can be adjustable through varying the time of O2 plasma treatment, which serve as a mask template for metal deposition on a silicon substrate. After the removal of the nanospheres, SiNWs having the exact same shape as the mask are synthesized using wet etching technique in a solution of HF, hydrogen peroxide, and deionized water. Different electrical and optical characteristics were obtained according to the shapes and sizes of the SiNWs, which implies that they can serve specific purposes according to their types.

• Analytical Science and Technology
• /
• v.16 no.2
• /
• pp.102-109
• /
• 2003

Microwave digestion and solid-state extraction were studied for determination of trace aluminum{Al(III)} in human urine samples. A mixed acid of nitric acid and hydrogen peroxide was added to urine samples, organic materials were destructed in a home microwave oven and dried in a drying oven. The dried residues were dissolved in a sulfuric acid solution. The solution was eluted through a XAD-4 resin column adsorbed with 8-hydroxyquinoline(Oxine, HQ). Al(III)-8-hydroxyquinolinate complex was formed in the column and eluted with 0.5 M nitric acid solution. The Al(III) eluted was determined by graphite atomic absorption spectrophotometry. Various experimental conditions of followings were investigated for the optimization : the type of acid to dissolve the residues, the amount of HQ adsorbed on the resin, the pH of sample solutions, the type and concentration of acid to elute the complex from column and so on. The contents of Al(III) in real samples were determinated by a calibration curve method. The recovery in standard spiked samples was 94~101% and the detection limit of this procedure was 0.05 ng/mL.