• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.150-152
• /
• 2009

본 연구는 염료감응형 태양전지에 적용되는 TiO2 나노입자를 개선하여 3차원적인 nanobranch를 수열법으로 합성하여 전자의 이동을 향상시키며, 비표면적을 늘려 효율향상을 위하여 전극 구조를 제어하였다. nanobranch의 seed인 nanowire를 XRDd, FE-TEM과 solar simulator를 이용하여 비교 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.553-556
• /
• 1999

This paper presents a proper condition to achieve above 19 % conversion efficiency using PC1D simulator. Cast poly-Si wafers with resistivity of 1 $\Omega$-cm and thickness of 250 ${\mu}{\textrm}{m}$ were used as a starting material. Various efficiency influencing parameters such as rear surface recombination velocity and minority carrier diffusion length in the base region, front surface recombination velocity, junction depth and doping concentration in the Emitter layer, BSF thickness and doping concentration were investigated. Optimized cell parameters were given as rear surface recombination of 1000 cm/s, minority carrier diffusion length in the base region 200 ${\mu}{\textrm}{m}$, front surface recombination velocity 100 cnt/s, sheet resistivity of emitter layer 100 $\Omega$/$\square$, BSF thickness 5 ${\mu}{\textrm}{m}$, doping concentration 5$\times$10$^{19}$ cm$^3$ . Among the investigated variables, we learn that a diffusion length of base layer acts as a key factor to achieve conversion efficiency higher than 19 %. Further details of simulation parameters and their effects to cell characteristics are discussed in this paper.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.930-937
• /
• 1997

Polycrystalline CdTe thin films have been studied for photovoltaic application because of their high absorption coefficient and optimal band energy(1.45 eV) for solar energy conversion. In this study CdTe thin films were deposited on CdS(chemical bath deposition)/ITO(indium tin oxide) substrate by rf-magnetron sputtering under various conditions. Structural optical and electrical properties are investigated with XRD UV-Visible spectrophotometer SEM and solar simulator respectively. The fabricated CdTe/CdS solar cell exhibited open circuit voltage( $V_{oc}$ ) of 610 mV short circuit current density( $J_{sc}$ ) of 17.2 mA/c $m^2$and conversion efficiency of about 5% at optimal sputtering conditions.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.2
• /
• pp.55-59
• /
• 2020

Copper Oxide (CuO) films were deposited on the n-type silicon wafer by rf magnetron sputtering for heterojunction solar cells. And then the samples were treated as a function of the annealing temperature (300-600℃) in a vacuum. Their electrical, optical and structural properties of the fabricated heterojunction solar cells were then investigated and the power conversion efficiencies (PCE) of the fabricated p-type copper oxide/n-type Si heterojunction cells were measured using solar simulator. After being treated at temperature of 500℃, the solar cells with CuO film have PCE of 0.43%, Current density of 5.37mA/㎠, Fill Factor of 39.82%.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.4
• /
• pp.187-191
• /
• 2004

In this work, we used the PCID simulator for simulation of solar cell and examined the effect of front-back surface recombination velocity, minority carrier diffusion length, junction depth and emitter sheet-resistance. As the effect of base thickness, the efficiency decreased by the increase in series resistance with the increase of the thickness and found decrease in efficiency by decrease of the current as the effect of the recombination. Also, as the effect of base resistivity, the efficiency increased somewhat with the decrease in resistivity, but when the resistivity exceeded certain value, the efficiency decreased as a increase in the recombination ratio. The optimum efficiency was obtained at the resistivity 0.5 $\Omega$-cm, and thickness $100\mu\textrm{m}$. We have successfully achieved 10.8% and 13.7% efficiency large area($103mm{\times}103mm$) mono-crystalline silicon solar cells without and with PECVD silicon nitride antireflection coating.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.412-415
• /
• 2008

In a research on the practical dye-sensitized solar cell, a study on a large module have preference because module must be able to generate the proper current that is possible to convert electrically. So the parallel connection of dye-sensitized solar cells which outputs a large current easily is essential. However, there is a current loss in a paralle connection of dye-sensitized solar cells and the loss becomes larger according to increasing the number of parallel connection. In this study, we analyzed the cause of the current loss in the parallel connection by using the equivalent circuit analysis. One DSC used in this experiment had an active area $8cm^2$(4.62cm$\times$1.73cm) and it attained a conversion efficiency of 5.43% under 1 sun illumination ($P_{in}$ of 100 mW/$cm^2$) using a solar simulator.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.247.1-247.1
• /
• 2016

Low-cost, high efficiency solar cells are tremendous interests for the realization of a renewable and clean energy source. ZnTe based solar cells have a possibility of high efficiency with formation of an intermediated energy band structure by impurity doping. In this work, ZnO/ZnTe:Cr and ZnO/i-ZnTe structures were fabricated by pulsed laser deposition (PLD) technique. A pulsed (10 Hz) Nd:YAG laser operating at a wavelength of 266 nm was used to produce a plasma plume from an ablated a ZnTe target, whose density of laser energy was 10 J/cm2. The base pressure of the chamber was kept at approximately $4{\times}10-7Torr$. ZnTe:Cr and i-ZnTe thin films with thickness of 210 nm were grown on p-Si substrate, respectively, and then ZnO thin films with thickness of 150 nm were grown on ZnTe:Cr layer under oxygen partial pressure of 3 mTorr. Growth temperature of all the films was set to $250^{\circ}C$. For fabricating ZnO/i-ZnTe and ZnO/ZnTe:Cr solar cells, indium metal and Ti/Au grid patterns were deposited on back and front side of the solar cells by using thermal evaporator, respectively. From the fabricated ZnO/ZnTe:Cr and ZnO/i-ZnTe solar cell, dark currents were measured by using Keithley 2600. Solar cell parameters were obtained under Air Mass 1.5 Global solar simulator with an irradiation intensity of 100 mW/cm2, and then the photoelectric conversion efficiency values of ZnO/ZnTe:Cr and ZnO/i-ZnTe solar cells were measured at 1.5 % and 0.3 %, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.465-466
• /
• 2009

Dye-sensitized Solar Cell (DSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The electric potential distribution in DSCs has played a major role in the operation of such cells. $TiO_2$ thin films were deposited on the ITO substrate by Nd:YAG Pulsed Laser Deposition(PLD) at room temperature and post-deposition annealing at $500^{\circ}C$ in flowing $O_2$ atmosphere for 1hour. The structural properties of $TiO_2$ thin films have investigated by X-ray diffraction(XRD). We manufactured DSC unit cells then I-V and efficiency were tested by solar simulator.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.360.1-360.1
• /
• 2014

DSSC (Dye-Sensitized Solar Cell)의 TCO (Transparent Conductive Oxide)와 전해질 사이의 전자 재결합(Back reaction)은 DSSC의 효율을 떨어뜨리는 요소 중 하나이다. 이와 같은 문제점을 해결하기 위하여 Blocking layer로서 $TiO_2$ 가 많이 사용되어지고 있다. 본 실험에서는 $HfO_2$ 를 Blocking layer로 사용하여 전자 재결합으로 인한 효율 저하를 막기 위한 연구를 진행하였다. 기존 $TiO_2$ 대비 $HfO_2$는 큰 에너지 밴드갭을 가지고 있어, TCO와 전해질 사이에 전자 재결합을 줄여주는 역할을 하기 때문에 DSSC의 효율 향상을 확인할 수 있다. 효율 측정은 1sun (100 mW/cm, AM1.5)조건에서 solar simulator를 이용하여 측정 했으며, 전자 재결합 감소는 Dark Current, EIS (Electrochemical Impedance spectroscopy)의 측정을 통하여 확인하였다. $HfO_2$를 이용한 blocking layer를 염료 감응 태양전지에 적용하면, 전자 재결합에 의한 손실을 줄여 성능적 측면에서 개선 가능할 것으로 생각된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.86.2-86.2
• /
• 2015

Cu2ZnSn(S,Se)4 thin film solar cells have been fabricated using sputtered Cu/Sn/Zn metallic precursors on Mo coated sodalime glass substrate without using a toxic H2Se and H2S atmosphere. Cu/Sn/Zn metallic precursors with various thicknesses were prepared using DC magnetron sputtering process at room temperature. As-deposited metallic precursors were sulfo-selenized inside a graphite box containing S and Se pellets using rapid thermal processing furnace at various sulfur to selenium (S/Se) compositional ratio. Thin film solar cells were fabricated after sulfo-selenization process using a 65 nm CdS buffer, a 40 nm intrinsic ZnO, a 400 nm Al doped ZnO, and Al/Ni top metal contact. Effects of sulfur to selenium (S/Se) compositional ratio on the microstructure, crystallinity, electrical properties, and cell efficiencies have been studied using X-ray diffraction, Raman spectroscopy, field emission scanning electron microscope, I-V measurement system, solar simulator, quantum efficiency measurement system, and time resolved photoluminescence spectrometer. Our fabricated Cu2ZnSn(S,Se)4 thin film solar cell shows the best conversion efficiency of 9.24 % (Voc : 454.6 mV, Jsc : 32.14 mA/cm2, FF : 63.29 %, and active area : 0.433 cm2), which is the highest efficiency among Cu2ZnSn(S,Se)4 thin film solar cells prepared using sputter deposited metallic precursors and without using a toxic H2Se gas. Details about other experimental results will be discussed during the presentation.