• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.248-250
• /
• 1987

Transparent CdS films with low electrical restivity on glass substrates were prepared by coating a CdS slurry which contained 10 wt.% $CdCl_2$, and sintering in a nitrogen atmosphere at $600^{\circ}C$ for 2hr. All-polycrystalline CdS/CdTe solar cells were fabricated by coating CdTe slurries, which contained 1.0 or 4.5 wt.% $CdCl_2$, on the sintered CdS films and sintering at $700^{\circ}C$ for various periods of sintering. The spectral responses of the sintered CdS/CdTe solar cells were measured and compared with theoretically calculated quantum efficiency. The spectral responses of the sintered CdS/CdTe solar cells in the short-wavelength region decreases with-increasing sintering time. The poor response in this region is attributed to the existence of the Cd-S-Te solid solution in the compositional junction. The decrease in the maximum response in the long-wavelength region as the sintering exceeds certain time appears to be caused by the increase in the depth of the buried homo junction and by the increase in the series resistance. The $CdCl_2$ in the CdTe layer during sintering enchances the interdiffusion of S, Te or donor impurities across the metallurgical Junction causing the formation of deeper n-p junction in the CdTe layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.461-462
• /
• 2005

In order to improve the efficiency of dye-sensitized solar cell (DSC), $TiO_2$ electrode screen-printed on transparent conducting oxide (TCO) substrate was sintered in variation with different temperature(350 to $550^{\circ}C$). $TiO_2$ electrode on fluorine doped tin oxide (FTO) glass was assembled with Pt counter electrode on FTO glass. I-V properties of DSC were measured under solar simulator. Also, effect of sintering temperature on surface morphology of $TiO_2$ films was investigated to understand correlation between its surface morphology and sintering temperature. Such surface morphology was observed by atomic force microscopy (AFM). From the measurement results, at sintering temperature of $500^{\circ}C$, both efficiency and fill factor of DSC were mutually complementary, enhancing highest fill factor and efficiency. Consequently, it was considered that optimum sintering temperature of $\alpha$-terpinol included $TiO_2$ paste is at $500^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1256-1257
• /
• 2008

Dye-Sensitized Solar Cell(DSSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The size and shape of $TiO_2$ particle are two of important parameters that are related to the characteristics of DSSC. And these can be changed by controlling $TiO_2$ sintering conditions especially temperature. The particles of $TiO_2$ are classified anatase and rutile. Anatase particles are created at low sintering temperature and rutile particles are created at high sintering temperature. Anatase particles have advantages such as increased surfaces that cause more attached dye molecules, and fast electron transportation. And rutile particles have advatages such as more efficient light scattering. Therefore, we studied characteristics of DSSC in this paper as $TiO_2$ sintering temperature is varied. As a result, we found that characteristics of DSSC are very good in the case that anatase and rutile particles are together and this sintering temperature is 450$^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.228-228
• /
• 2013

Dye-Sensitized Solar Cells (DSSCs) have attracted great interests as they offer high energyconversion efficiencies at low cost. For the conventional fabrication of DSSCs, high temperature sintering is required for the construction of interconnect $TiO_2$. However, more simplified process which can be applicable to large-sized solar cells module, is strongly necessary for the commercialization of DSSCs. In this work, we developed novel sintering method using Intense Pulsed Light (IPL), which can replace the conventional high temperature sintering methods. The photovoltaic properties of DSSCs utilizing IPL methods will be reported.

• Electrical & Electronic Materials
• /
• v.1 no.1
• /
• pp.26-34
• /
• 1988

Sintered CdS/CdTe solar cells have been farbricated by coating a (Cd+Te) slurry on sintered CdS films followed by the sintering at 625.deg.C for one hour with various heating rates. When cadmium and tellurinm powders are used instead of CdTe powder to form CdS/CdTe junction, CdTe is formed in the temperature range of 290.deg.C-400.deg.C. The microstructure of the CdTe films depends strongly on the heating rate of the sintering due to the low melting temperature and the high vapor pressure of the elemental Cd and Te. An optimum heating rate obtain CdTe films with uniform and dense microstructure which, in turn, improves the efficiency of the sintered CdS/CdTe solar cells. All-polycrystalline CdS/CdTe solar cells with an efficiency of 9.57% under 50mW/cm$^{2}$ tungsten light have been farbricated by using a heating rate of 14.deg.C/min.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.56-58
• /
• 1989

All-polycrystalline Cd$_1$-xZnxS/CdTe solar cells have been fabricated by coating CdTe slurries with 4.5 wt% of CdCl$_2$on the sintered Cd$_1$-xZnxS films and by sintering CdTe layer at 6$25^{\circ}C$ for lh in nitrogen atmosphere. Solar efficiency of the sintered Cd$_1$-xZnxS/CdTe solar cells increases as the Zn content increases up to x=0.06 and then decreases with further increase in the Zn content. A solar efficiency of 12.5% under a solar intensity of 76mW/$\textrm{cm}^2$ was observed in a Cd 0.94 Zn0.06S/CdTe solar cell. By optimizing the amount of CdCl$_2$in the slurry and sintering conditions, it is possible to produce Cd$_1$-xZnxS/CdTe solar cells with efficiency higher than 12%.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.227-228
• /
• 2012

In interfaces between carbon black or Pt and FTO glass in dye-sensitized solar cell counter electrodes, a marginal resistant channel for electrons, we tried to improve the connection by modifying the sintering process. A stepwise sintering process for carbon black and Pt counter electrodes was applied and its effect on power conversion efficiency was studied. Power conversion efficiencies of built-in DSSC made by a one-step sintering process with carbon black and Pt counter electrodes were about 5.01% and 5.02%, respectively. Cells made with the stepwise sintering process were 5.96% and 6.21%, respectively, indicating an 20% improvement. Fill factor (FF) increased, and it was them main reason for the power conversion efficiency improvement. Step wise sintering increased the adhesion of the interface and reduced the film thickness and surface roughness. As a result, the resistivity of the counter electrode and EIS impedance of DSSCs decreased.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.114.1-114.1
• /
• 2011

Electrical sintering of the front electrode for crystalline silicon solar cells was performed applying a constant DC current to the printed lines. Conducting lines were printed on glass substrate by a drop-on-demand (DOD) inkjet printer and silver nanoparticle ink. Specific resistance and microstructure of sintered silver lines and were measured with varying DC current. To find the relation between temperature increase with changing applied current and specific resistance, temperature elevation was also calculated. Sintering process finished within a few milliseconds. Increasing applied DC current, specific resistance decreased and grain size increased after sintering. Achieved minimum specific resistance is approximately 1.7 times higher than specific resistance of the bulk silver.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.6
• /
• pp.571-575
• /
• 2005

In order to improve the efficiency of dye-sensitized solar cell (DSSC), $TiO_2$ electrode screen-printed on transparent conducting oxide (TCO) substrate was sintered in variation with different temperature$(350\;to\;550^{\circ}C)$. $TiO_2$ electrode on fluorine doped tin oxide (FTO) glass was assembled with Pt counter electrode on FTO glass. I-V properties of DSSCs were measured under solar simulator. Also, effect of sintering temperature on surface morphology of $TiO_2$ films was investigated to understand correlation between its surface morphology and sintering temperature. Such surface morphology was observed by atomic force microscopy (AFM). Below sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively lower due to lower open circuit voltage. Oppositely, above sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively higher due to higher open circuit voltage. In both cases, lower fill factor (FF) was observed. However, at sintering temperature of $500^{\circ}C$, both efficiency and fill factor of DSSCs were mutually complementary, enhancing highest fill factor and efficiency. Such results can be explained in comparison of surface morphology with schematic diagram of energy states on the $TiO_2$ electrode surface. Consequently, it was considered that optimum sintering temperature of a-terpinol included $TiO_2$ paste is at $500^{\circ}C$.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.9
• /
• pp.1233-1238
• /
• 2014

In this thesis, it is investigated the characteristics of Dye Sensitized Solar Cell (DSSC) according to variation of $TiO_2$ thickness (6, 12, 18, and $24{\mu}m$) and three distinct $TiO_2$ sintering temperatures (350, 450 and $550^{\circ}C$) by XRD, SEM, I-V and UV-Vis spectrophotometer. According to sintering temperature, $TiO_2$ was transformed into the anatase structure at $350^{\circ}C$, rutile structure at $550^{\circ}C$ and further into the two structure at $450^{\circ}C$. With increasing thickness up to $18{\mu}m$ and sintering temperature up to $450^{\circ}C$, respectively, the irradiance rate increased in the range of 9~26 percent and 2.80~5.10 percent. Whereas a further increase to $24{\mu}m$ and $550^{\circ}C$, the irradiance rate decrease in the range of 4~11 percent and 30~47 percent. The conversion efficiency increased in the range of 2.80~5.01 and 3.03~5.01 with increasing thickness up to $18{\mu}m$ and sintering temperature up to $450^{\circ}C$. By contrast, increase to $24{\mu}m$ and $550^{\circ}C$, the conversion efficiency decreased in the range of 3.31~5.01 and 2.80~3.89, respectively. The DSSC that thickness of $TiO_2$ were $18{\mu}m$ and sintered at $450^{\circ}C$ exhibited the most excellent characteristics, in which open-circuit voltage, short-circuit current, Fill Factor and conversion efficiency are 0.69 V, $11.4mA/cm^2$, 0.64 and 5.01%, respectively.