• Proceedings of the KSRS Conference
• /
• 2009.03a
• /
• pp.254-259
• /
• 2009

In this study, Simplified Method for the Atmospheric Correction (SMAC) radiative transfer model (RTM) used to retrieve surface reflectance from MODIS Top Of Atmosphere (TOA) reflectance (MOD02). SMAC code provides coefficients which were previously yielded by Second Simulation of the Satellite Signal in the Solar Spectrum (6S) for each satellite sensor. We conducted error analysis of SMAC RTM using MOD02 over comparison with MODIS surface reflectance (MOD09) which was provided from 6S. It showed that low accuracy values such as, $R^2$ : 0.6196, Root Means Square Error (RMSE) : 0.00031, bias : - 0.0859. Thus sensitivity analysis of input parameters and coefficients was conducted to searching error sources. Coefficients about $\tau_p$ (average AOD) are more influence than any other coefficients of $\tau_{a550}$ (Aerosol Optical Depth at 550nm) from sensitivity test. Calibrated coefficients of $\tau_p$ from regression analysis were used to surface reflectance which showed that improve accuracy of surface reflectance ($R^2$ : 0.827, RMSE : 0.00672, bias : - 0.000762).

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1592-1594
• /
• 2003

This paper presents the deposition and characterization of microcrystalline silicon(${\mu}c$-Si:H) films by HWCVD(Hot-wire Chemical Vapor Deposition) method at low substrate($300^{\circ}C$). The filament temperature, pressure and $SiH_4$ concentration were determined to be a critical parameter for the deposition of poly-Si films. Series A was deposited under the conditions of $1380^{\circ}C$(Tf), 100 mTorr and $2{\sim}10%\{SC:SiH_4/(SiH_4+H_2)\}$ for 60 min. Series B was deposited under the conditions of $1400{\sim}1450^{\circ}(T_f)$, 30 mTorr and $2{\sim}12%$(SC) for 60 min. The physical characteristics were measured by Raman and FTIR spectroscopy, dark and photoconductivity measurements under AM1.5 illumination.

• Bulletin of the Korea Photovoltaic Society
• /
• v.3 no.2
• /
• pp.42-47
• /
• 2017

The potential induced degradation (PID) phenomenon shows severe power loss within several years from the initial installation of solar power system. The accumulated power loss by PID is inevitable because the PID is suspected only if the power loss exceeds several percent. In this paper, we analyzed the cases of PID diagnosis and recovery by visiting the suspected PID site about 17 months after the installation of the 100kW PV system. The power difference of the two 50kW inverters was more than 20kWh, and the PR difference was more than 8%. From the beginning of the installation, the difference in power gradually increased. The recovery was observed for about 7 months by applying 1000V in the reverse bias at night. As a result, the power difference of the two inverters was recovered to within 2kWh. In the case of a power station suffering from PID in the field, it will be helpful for stable development operation by quick diagnosis and problem solving.

• Journal of Satellite, Information and Communications
• /
• v.6 no.2
• /
• pp.112-116
• /
• 2011

Effect analysis tool for space infrastructure has a role to give essential information which is needed to perform research systematically as effect analysis for satellites on earth orbit due to solar burst and statistical analysis for deriving key factor which is occurred anomalies to satellite. And retrieval function which is able to search domestic and foreign research data such as paper, report, journal and book related to satellite anomaly is also included. So this tool will be provided research environment for effect analysis from space environment to space infrastructure of earth orbit satellite. In this paper, it is shown design result for effect analysis for space infrastructure including DB design.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.6
• /
• pp.96-103
• /
• 2009

Wind power, Solar power and Fuel cell is the representative of new and renewal energy sources. In this paper, the frictional noise made by vehicles tire on roads is considered and researched as alternative electrical generation source. The amplitude and waveform of generated electricity with various types of vehicles according to their velocity, weight and distances between vehicles and sensor are measured and analyzed. As a result, all difference effects mentioned above which make the frictional noise affect quality and quantity of generated electricity. Maximum 0.53[V] and 0.028[W] electricity was generated by truck with 100[km/h] velocity on the express way.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2009.06a
• /
• pp.287-288
• /
• 2009

In this paper we developed positioning algorithm considering distributed energy resource of ocean side by load flow calculation using Newton-Rhapson method.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.289-290
• /
• 2012

This paper proposes a new active snubber boost PFC converter to provide a zero-voltage-switching (ZVS) turn-on condition and reduce electromagnetic interference (EMI) noise in home appliances and renewable energy applications, including solar or fuel cell electric systems. The proposed active snubber circuit enables a main boost switch of the boost-type PFC or grid converter to turn on under a ZVS condition and reduce the switching losses of the main boost switch. Moreover, for the purpose of a specialized intelligent power module (IPM) fabrication, the proposed boost circuit is designed to satisfy some design aspects such as space saving, low cost, and easy fabrication. Simulation and experimental results of a 2kW IPM boost-type PFC converter are provided to verify the effectiveness of the proposed active snubber boost circuit.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.368-368
• /
• 2007

Zinc oxide (ZnO) has drawn much interest as a potential transparent conducting oxide (TCO) for applying to solar cell and front electrode of electro-luminescent devices. For the enhancement of electrical property of TCOs, dopant introduction and hybridization with conductive nanoparticles have been investigated. In this work, ZnO films were formed on glass substrate by using photochemical solution deposition of Ag nanoparticles dispersed or various metal (Ag, Cd, In, or Sn) contained photosensitive ZnO solutions. The usage of photosensitive solution permits us to obtain a micron-sized direct patterning of ZnO film without using conventional dry etching procedure. The structural, optical, and electrical characteristics of ZnO films with the introduction of metal dopants with/without Ag nanoparticles have been investigated to check whether there is a combined effect between metal dopants and Ag nanoparticles on the characteristics of ZnO film. The phase formation and crystallinity of ZnO film were monitored with X-ray diffractometer. The optical transmittance measurement was carried out using UV-VIS-NIR spectrometer and the electrical properties such as sheet resistance and conductivity were observed by using four-point probe.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.446-447
• /
• 2007

The rapid thermal annealing effect of transparent IZTO(indium zinc oxide) and IAZO(indium alminium zinc oxide) films grown on glass substrate for solar cell or flat panel displays(FPDs) was studied. We prepared IZTO using RF magnetron sputtering and IAZO using DC co-sputtering method. Subsequently, using rapid thermal annealing(RTA) system, prepared IZTO and IAZO films were annealed at 300, 400, 500, $600^{\circ}C$ for 90sec. In addition, Electrical and optical characteristics were measured by Hall effect measurement and UV/Vis spectrometer examinations, respectively. To analyze structural properties and surface smoothness of the IZTO and IAZO films, XRD and SEM examinations were performed, respectively. It was shown that IZTO and IAZO films exhibited microcrystalline structure over $400^{\circ}C$ and amorphous structural regardless of RTA temperature, respectively.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1293-1294
• /
• 2007

태양전지는 대표적인 결정질 실리콘 태양전지를 비롯해 다양한 종류가 있지만 모두 입사광의 광량이나 광도에 출력이 의존한다는 점은 공통적이다. 이는 입사광의 에너지를 받아 염료 분자의 여기를 통해 전자를 생산하는 염료감응형 태양전지의 매커니즘에도 적용되는 것이다. 즉, 입사광의 광도나 광량의 값이 클수록 염료감응형 태양전지는 더 높은 출력전력을 생산한다는 의미이다. 본 연구에서는 투명성 때문에 입사광의 투과도가 높은 염료감응형 태양전지의 특성에 착안해 상대전극에 금속박막을 sputtering함으로써 입사광의 반사율을 증가시켜 입사된 광의 에너지를 더 효과적으로 활용할 수 있는 방법을 시도했다. 금속박막의 재료로 니켈, 백금, 은을 대상으로 실험한 결과, 금속박막을 sputtering 하지 않은 경우에 비해 전체적으로 염료감응형 태양전지의 효율이나 전력면에서 개선된 결과를 얻었고 그 중 백금 반사막을 입힌 셀로부터 최대 24.4%의 투과도 감소를 비롯, 11.5%의 출력전력의 증가와 0.4%의 효율 상승을 이끌어냈다.