• Journal of Power Electronics
• /
• v.7 no.2
• /
• pp.109-117
• /
• 2007

In this paper, a novel proposal for a utility-interactive three-phase soft commutation sinewave PWM power conditioner with an auxiliary active resonant DC-link snubber is developed for fuel cell and solar power generation systems. The prototype of this power conditioner consists of a PWM boost chopper cascaded three-phase power conditioner, a single two-switch auxiliary resonant DC-link snubber with two electrolytic capacitors incorporated into one leg of a three-phase V-connection inverter and a three-phase AC power source. The proposed cost-effective utility-interactive power conditioner implements a unique design and control system with a high-frequency soft switching sinewave PWM scheme for all system switches. The operating performance of the 10 kW experimental setup including waveform quality, EMI/RFI noises and actual efficiency characteristics of the proposed power conditioner are demonstrated on the basis of the measured data.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.289-290
• /
• 2012

This paper proposes a new active snubber boost PFC converter to provide a zero-voltage-switching (ZVS) turn-on condition and reduce electromagnetic interference (EMI) noise in home appliances and renewable energy applications, including solar or fuel cell electric systems. The proposed active snubber circuit enables a main boost switch of the boost-type PFC or grid converter to turn on under a ZVS condition and reduce the switching losses of the main boost switch. Moreover, for the purpose of a specialized intelligent power module (IPM) fabrication, the proposed boost circuit is designed to satisfy some design aspects such as space saving, low cost, and easy fabrication. Simulation and experimental results of a 2kW IPM boost-type PFC converter are provided to verify the effectiveness of the proposed active snubber boost circuit.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.460-464
• /
• 2020

This study reports the fabrication and application of semitransparent Cu nanoparticle layers. Spin coating and subsequent drying of a Cu colloid solution were performed to deposit Cu nanoparticle layers onto Si and glass substrates. As the spin speed of the spin coating increases, the density of the nanoparticles on the substrate decreases, and the agglomeration of nanoparticles is suppressed. This microstructural variation affects the optical properties of the nanoparticle layers. The transmittance and reflectance of the Cu nanoparticle layers increase with increasing spin speed, which results from the trade-off between the exposed substrate area and surface coverage of the Cu nanoparticles. Since the glass substrates coated with Cu nanoparticle layers are semitransparent and colored, it is anticipated that the application of a Cu nanoparticle-dielectric bilayer structure to transparent solar cells will improve the cell efficiency as well as aesthetic appearance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.312.2-312.2
• /
• 2013

태양전지에서 SiNX층은 반사방지막 역할과 표면 페시베이션의 역할을 동시에 하고 있다. SiNx에서 굴절율과 두께는 반사율과 밀접한 관계가 있으며 동시에 표면 소수캐리어 수명에도 큰 영향을 미친다. 따라서 굴절율과 두께를 조절하여 낮은 반사도와 긴 소수캐리어 수명을 가지는 SiNx 박막을 제조하여야 우수한 효율의 태양전지를 제조할 수 있다. 본 연구에서는 다양한 굴절율과 두께의 SiNx 박막을 결정질 실리콘 태양전지에 적용하여 효율과의 상관관계를 해석하였다. SiNx 박막은 PECVD장비를 이용하여 RF파워, 가스혼합량, 증착시간 등을 각각 변화시키며 형성하였다. RF 파워는 100~500 W로 변화 시켰고 혼합가스 변화는 SiH4가스와 NH3가스, Ar가스를 각각 주입하며 증착하였다. RF 파워 300W, 가스혼합량 SiH4 90sccm, NH3 26sccm, Ar 99sccm과 기판 온도 $300^{\circ}C$, 공정시간 58초에서 포면 반사율 1.09%와 굴절률 1.965, 두께 76nm를 갖는 SiNx층을 형성 할 수 있었다. SiNx층을 증착하여 셀을 제작한 결과, 개방전압: 0.612V, 전류밀도: 38.49 mA/cm2, 충실도: 75.62%, 효율: 17.82%를 얻을 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.218-221
• /
• 2006

The photovoltaic properties of CIES cells on alumina substrate were improved by using the Na-doped Mo as theabotom layer of hilo back contact. Na was supplied to the CIGS bulk region from alumina/Na-doped Mo/Mo/alumina? structure, as same assimilar to the Na diffusion from soda-lime glass. The content diffusion of Na from Na-doped bfo was smaller more controlled than that from SLG. These Our results indicate that Na-doped bfo act as Na source material and contents of Na amount can be controlled without the use of an alkali barrier layer. The best CIGS solar cell with conversion efficiency of 13.34%, $J_{sc}=34.62mA/cm^2,\;V_{oc}=0.58V$ and FF=66% for an active area of $0.45cm^2$ on the alumina substrate was obtained in the condition of for 100nm Na-doped Mo/1000nm Mo.

• Current Optics and Photonics
• /
• v.2 no.6
• /
• pp.514-518
• /
• 2018

Carrier diffusion length in the light-sensitive material is one of the key elements in improving the light-current conversion efficiency of solar-cell devices. In this paper, we measured the carrier diffusion length in lead-halide perovskite ($MAPbI_3$) and mixed lead-halide ($MAPbI_{3-x}Cl_x$) perovskite devices using scanning photocurrent microscopy (SPCM). The SPCM signal decreased as we moved the focused laser spot away from the metal contact. By fitting the data with a simple exponential curve, we extracted the carrier diffusion length of each perovskite film. Importantly, the diffusion length of the mixed-halide perovskite was higher than that of the halide perovskite film by a factor of 3 to 6; this is consistent with the general expectation that the carrier mobility will be higher in the case of the mixed lead-halide perovskites. Finally, the diffusion length was investigated as a function of applied bias for both samples, and analyzed successfully in terms of the drift-diffusion model.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.561-564
• /
• 2014

In this paper a photovoltaic energy harvesting charger with battery management circuit is proposed. The proposed circuit harvests maximum power from a solar cell by employing MPPT(Maximum Power Point Tracking) control and charges an external capacitor battery with the harvested energy. The charging state of the battery is controlled according to the signals from the battery management circuit. The proposed circuit is designed in a 0.35um CMOS process technology and its functionality has been verified through extensive simulations. The maximum efficiency of the designed entire system is 84.8%, and the chip area including pads is $1350um{\times}1200um$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.705-705
• /
• 2013

CIGS 박막태양 전지는 I-III-VI Chalcopyrite 결정구조를 가진 화합물 반도체 태양전지로 인위적인 밴드갭 조작을 통하여 효율 향상에 용이하다. 4원소 화합물인 CIGS 광흡수층의 대표적인제조 방법으로는 co-evaporation 공정법이 있다. 동시 증발법은 CIGS 결정을 최적화하기 위하여 박막이 증착되는 동안 기판의 온도를 3단계로 변화시켜주는 3-stage 공정을 통하여 제작된다. 일반적으로 CIGS 박막태양전지는 전면전극으로 투명전도막이 사용되며 높은 광투과성과 전기전도성을 가져야 한다. 투명전도막의 광학적, 전기적 특성은 CIGS 박막태양전지의 효율에 영향을 미치기 때문에 최적화된 조건이 요구된다. 본 연구에서는 CIGS 광흡수층은 Ga/(In+Ga)=0.31, Cu/(In+Ga)=0.86으로 최적화 시켰으며, 투명전도막은 Ga이 도핑된 ZnO박막을 RF 마그네트론 스퍼터링법을 이용하여 증착하였다. CIGS 박막 태양전지 직렬저항 성분인 투명 전도막의 비저항이 $4.46{\times}{\square}10{\square}-3{\square}$(${\Omega}$-cm)에서 $9.3{\times}{\square}0{\square}-4{\square}$(${\Omega}$-cm) 으로 변화함에 따라 Efficiency가 9.67%에서 16.47%으로 증가하였으며, Voc가 508 mV에서 596 mV으로, Jsc가 29.27 mA/$cm^2$에서 37.84 mA/$cm^2$으로, FF factor가 64.99%에서 72.96%로 증가하였다. 이에 따른 투명 전도막의 전기적, 광학적 특성을 통해 CIGS 박막태양전지에 미치는 영향에 대해 조사하였다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.5
• /
• pp.853-858
• /
• 2022

In this paper, we show a simultaneous transmission of underwater optical wireless power transfer and underwater optical wireless communication. A laser diode is used for electric-to-optic conversion at the transmitter and a solar cell is used for optic-to-electric conversion at the receiver. We optimized the transmitter and receiver for the best performance. The laser diode is a 100-mW laser diode and showed a conversion efficiency of 18.5%. The experimental results showed a 0.33-% DC-to-DC underwater power transfer efficiency at 5 m and a data rate of 100 kbps at 1 m.

• Current Photovoltaic Research
• /
• v.5 no.2
• /
• pp.47-54
• /
• 2017

We report finding ways to improve the long-term reliability of PV module including the heterostructure with the intrinsic thin layer (HIT) solar cell. We point out the stability of the products of Panasonic HIT cell. We account for a brief description of the module manufacturing process to investigate the issues of each process and analyze the causes. We carried out the silicon PV module of the glass to glass type under the damp heat test around 1000 hours. However, it degraded around 7% of PV module power after 300 hours exposure in comparison with the initial status (Initial: 12.7 Watt). We investigated possible cause and solutions for the module performance to develop the long-term reliability.