• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.17-24
• /
• 1995

The TEA complex polymeric sol was prepared by the alkoxide sol-gel method. The purpsoe of this experiment was to vefity the particle shape in the sol from the investigation of the rheological properties. TEA retarded hydrolysis rate by the reaction with alkoxide enough to make a stable transparent sol in the wide range of composition. From the results of the viscosity change with time, the optimum mole ratio for spinning was selected as 0.5 mole of TEA, 3 mole of H2O and the optimum viscosity was 104 cPs. The rheological behavior of the sol showed that the particle shape in the sol was linear, which was adequate for fiber drawing.

• Journal of the Korean Ceramic Society
• /
• v.28 no.1
• /
• pp.60-66
• /
• 1991

The polymeric alumina sol was prepared by partial hydrolysis of aluminum sec-butoxide reacted with acetylacetone and its characteristics was investigated. The effects of alcohol solvent, acetylacetone, and acid concentration to the sol were investigated. FT-IR and Al27-MASNMR were used to study hydrolysis and polymerization reaction of aluminum complex. Synthesized sol showed the characteristics of polymeric alumina sol. To make a clear polymeric alumina sol, the optimum contents of acetylacetone, H2O and alcohol solvent were 0.4-0.6 mole, 0.25-1.25 mole, 3-5 mole per one mole alkoxide respectively. As a result of the Al27-MASNMR analysis, it was noted that hexa-penta-coordinated Al were main structure.

• Korean Journal of Microbiology
• /
• v.32 no.3
• /
• pp.208-214
• /
• 1994

We screened many species from a wide variety of bacterial genera for a new type II restriction endonuclease. The purification and characterization of SolI from a soil isolate, Streptoverticillium olivoverticillatum are described here. The enzyme turned out to be an isoschizomer of BamHI. It recognized the hexanucleotide sequence of 5'-G$\downarrow$GATCC-3' and cleaved as in dicated by the arrow, generating a 4 base 5' extension. Unlike its isoschizomer, BamHI, the activity was sensitive to dam methylation within the recognition sequence. Following ammonium sulfate fractionation of the crude extract, heparin-agarose and Affi-gel Blue column chromatography were employed to purify the enzyme. SolI required at least 0.2 mM of $MgCl_2$ for the cleavage to occur. The enzyme exhibited its maximal activity in the absence of NaCl, but was inhibited completely in the presence of 120 mM NaCl. The pH and temperature optima for activity were pH 8.6 and $40^{\circ}C$, respectively. The molecular weight of SolI was estimated to be 43,000 Da by Superose-12 gel filtraion chromatography.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1060-1068
• /
• 1994

Stable zirconia sol was prepared from zirconium butoxide Zr(OC4O9)4 as a precursor and ethylacetoacetate(EAcAc) or diethylene glycol(DEG) as a chelating agent under ambient agent under ambient atmosphere by Sol-Gel process. The sythesized sol was coated on 304 stainless steel substrate by dip coating, thereafter zirconia film could be obtained by heat-treatment at $600^{\circ}C$. The characteristics of coating film were determined by FT-IR, XRD, and ellipsometion peak represented Zr-O-Zr bonding of tetragonal phase was shown at 470cm-1. Crystallization of zirconia gel and film from amorphous state to tetragonal phase started at 40$0^{\circ}C$, and then transformed into monoclinic phase around $700^{\circ}C$. Zirconia film coated on 304 stainless steel substrate showed relatively low porosity of 16% when it was coated with 0.4M zirconia sol and thereafter heat-treated at 80$0^{\circ}C$ and the film was densified continuously up to 90$0^{\circ}C$. The zirconia film of 10 nm thick acted as a protective layer against oxidation up to $700^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.795-801
• /
• 1989

The polycrystalline mullite fiber was synthesized from various combination of starting materials including metal alkoxides and colloidal sol by the sol-gel process. The best spinnability was observed in the sol which showed shear thinning and hysteresis (i.e., thixotropic flow), indicating that the network structure was broken down as the shear rate increased. The mullite fiber was polycrystalline after firing and characterized by thermal analysis, XRD, FT-IR spectroscopy, rheological measurements, and SEM.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.527-531
• /
• 2016

In this study, p-type thin film transistors consisting of CuO channels were fabricated by sol-gel process, with copper (II) acetate monohydrate precursors. At $500^{\circ}C$, the deposited films were fully converted into monoclinic phase CuO. The fabricated CuO thin film transistors deliver field effect mobility in saturation regime of $0.015cm^2/Vs$, and $I_{on}/I_{off}$ of ${\sim}10^3$. The degradation of the performance of the fabricated CuO thin film transistor caused by the exposure to air has been studied.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1189-1196
• /
• 2003

Ferroelectric B $i_{3.25}$L $a_{0.75}$ $Ti_3$ $O_{12}$ (BLT) solution was synthesized by sol-gel process. BLT thin films were deposited on Pt/Ti $O_2$/ $SiO_2$/Si substrates by spin-coating. In this experiments, Bi(TMHD)$_3$, La(III)2-Methoxyethoxide, and Ti(IV) i-propoxide were used as starting materials, which were dissolved in 2-Methoxyethanol. Rapid Thermal Annealing (RTA) was used to promote crystallization of BLT thin films. The thin films with RTA process were compared with those with non-RTA process on electrical properties. After RTA process, the remanent polarization value (2Pr) of BLT thin films annealed at 72$0^{\circ}C$ was 20.46 $\mu$C/$\textrm{cm}^2$ which was approximately 27% higher than that of non-RTA process at 5 V.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.804-812
• /
• 1994

Stable PZT coating sol was prepared using chelating agent, ethylacetoacetate(EAcAc) by sol-gel processing under ambient atmosphere. Through FT-IR spectrum analysis on solution of each reaction step, formation of metal complex was confirmed and prepared PZT sol was stable over several months. Through TG-DTA, XRD, FT-IR spetrum analysis of PZT gel powder, it was understood that the addition of EAcAc could reduce the transition temperature to ferroelectric phase, due to the increased homogeneity by matching the hydrolysis and condensation rates by chelation. Single perovskite phase was obtained by the heat-treatment at 54$0^{\circ}C$ for 30 min. The film was coated on ITO-coated glass substrate by dip coating method. After heat-treatment, PZT thin film had thickness in the range of 20~130 nm. The maximum dielectric constant of its thin film at room temperature and 1 kHz was 128.

• Journal of Adhesion and Interface
• /
• v.20 no.4
• /
• pp.146-154
• /
• 2019

In this study, alkoxysilane-functionalized amphiphilic polymer (AFAP), which have hydrophilic segment and hydrophobic segment functionalized by alkoxysilane group at the same backbone, was synthesized and used as a dispersant and control agent for reaction rate in the preparation of colloidally stable organic-inorganic (O-I) hybrid sols. After reaction with fluorosilane compounds, fluorinated O-I hybrid sols were prepared and coated onto glass substrate to form hydrophobic O-I hybrid coating films through low-temperature curing process. Surface hardness and hydrophobicity of cured coating films were varied with type of solvent and composition of AFAP and fluorinated alkoxysilane compounds. At appropriate solvent and composition of fluorinated alkoxysilane compounds, O-I hybrid coating film having high transparency and surface hardness could be prepared, which could be applicable to cover window of solar cell and displays.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.881-892
• /
• 1995

Sol-Gel derived ferroelectric PZT thin films were fabricated on ITO/Glass substrate. Two kinds of rapid thermal annealing methods, R-I (six times of intermediate and final annealing) and R-II (one final annealing after six times of intermediate annealing) were used for preparation of multi-coated PZT thin films. 2500$\AA$-thick PZT thin films were obtained by the R-I and R-II methods and characterized by microstructure and dielectric properties. In case of using R-II, the microstructure was finer than that of R-I and there was no distinguishable difference in dielectric properties of PZT thin films between the R-I and R-II methods. But dielectric properties were enhanced by increasing perovskite phase fraction with increasing annealing temperature. Measured dielectric constant of PZT thin film annealed at 62$0^{\circ}C$ using the R-I method was 256 at 1kHz. Its remanant polarization (Pr) and coercive field (Ec) were 14.4$\mu$C/$\textrm{cm}^2$ and 64kV/cm, respectively.