• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.10a
• /
• pp.84-89
• /
• 2000

Thermal simulation of typical stack-type and newly proposed planar-type micro-gas sensors were studied by FEM method. The thermal analyses for the proposed planar structure including temperatur distribution over the sensing layer and power consumption of the heater were carried using finite element method by computer simulation and well compared with those of typical stack-type micro-gas sensor. The thermal properties of the microsensor from thermal simulation were compared with those of a actual device to investigate the acceptability of the computer simulation.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.60-63
• /
• 2000

In this paper, 7-segment was implemented using AC powder EL. ZnS:Cu and BaTiO3 was used as a phosphor and dielectric respectively. The preparation of phosphor and dielectric layer was performed with screen printing. The implemented system of 7-segment was divided as following; EL display, driving circuit, software for driving. The properties of fabricated devices was measured with EL spectrum and brightness.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.428-430
• /
• 2000

In this paper, the Flexible information display was implemented using AC powder electroluminescent device. ZnS:Cu and $BaTiO_3$ was used as a phosphor and dielectric respectively. The preparation of phosphor and dielectric layer was performed with screen printing. The implemented system of the Flexible information display was divided as following; EL display, driving circuit, software for driving. The properties of fabricated devices was measured with EL spectrum and brightness.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1984.10a
• /
• pp.7-10
• /
• 1984

In this paper, the advantages of buffer insertion access method in comparison with other access methods to local area networks are analyzed. Sending and Receiving protocols in a data link layer are designed by a software method, We have derived both qeueing delays and the response time for the performance model that is proposed in this paper, and using the computer simulation, analyzed the performance for the proposed model in terms of the throughput rate- response time characteristrics. Based on the proposed model, the hardware design is implemented.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.292-293
• /
• 2013

Sub 10-nm thick of Si plate is simulated with the software for Nanowire Field Effect Transistor (FET) device simulation. With usual single crystal Si technology, it is difficult to realize flexible electronic devices. Here, we suggest a FET device based on thinned Si layer. The simulation implied a practical limitation of the Si plate thickness for flexible devices as 2 nm. With around this thickness, Si plate may have much flexibility than existing bulk MOSFETs.

• Geomechanics and Engineering
• /
• v.9 no.6
• /
• pp.757-774
• /
• 2015

Reinforcing soils with the geosynthetics have been shown to be an effective method for improving the uplift capacity of granular soils. The pull-out resistance of the reinforcing elements is one of the most notable factors in increasing the uplift capacity. In this paper, a new reinforcing element including the elements (anchors) attached to the ordinary geogrid for increasing the pull-out resistance of the reinforcement, is used. Thus, the reinforcement consists of the geogrid and anchors with the cylindrical plastic elements attached to it, namely grid-anchors. A three-dimensional numerical study, employing the commercial finite difference software FLAC-3D, was performed to investigate the uplift capacity of the pipelines buried in sand reinforced with this system. The models were used to investigate the effect of the pipe diameter, burial depth, soil density, number of the reinforcement layers, width of the reinforcement layer, and the stiffness of geogrid and anchors on the uplift resistance of the sandy soils. The outcomes reveal that, due to a developed longer failure surface, inclusion of grid-anchor system in a soil deposit outstandingly increases the uplift capacity. Compared to the multilayer reinforcement, the single layer reinforcement was more effective in enhancing the uplift capacity. Moreover, the efficiency of the reinforcement layer inclusion for uplift resistance in loose sand is higher than dense sand. Besides, the efficiency of reinforcement layer inclusion for uplift resistance in lower embedment ratios is higher. In addition, by increasing the pipe diameter, the efficiency of the reinforcement layer inclusion will be lower. Results demonstrate that, for the pipes with an outer diameter of 50 mm, the grid-anchor system of reinforcing can increase the uplift capacity 2.18 times greater than that for an ordinary geogrid and 3.20 times greater than that for non-reinforced sand.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.5
• /
• pp.807-816
• /
• 2021

With the technology of the 4th industrial revolution, network traffic is increasing due to an increase in supply, an increase in demand, and an increase in the complexity of traffic patterns. SDN, a concept in which H/W and S/W are separated in order to efficiently manage such massive traffic, is attracting attention as a next-generation network. A lot of research is being conducted on the merits of applying flexible policies by avoiding the problem of rigid vendor dependency by using the SDN controller implemented with S/W Opensource. Therefore, in this paper, we propose an efficient load balancing technique by grouping through the packet structure of the network layer using the control layer and infrastructure layer of SDN and analyzing the packet delay and reception rate.

• Journal of Convergence for Information Technology
• /
• v.11 no.7
• /
• pp.31-38
• /
• 2021

In this paper, in order to obtain the optimization of the RNN model used for sentiment analysis, the correlation of each model was studied by observing the trend of loss and accuracy according to hyperparameter tuning. As a research method, after configuring the hidden layer with LSTM and the embedding layer that are most optimized to process sequential data, the loss and accuracy of each model were measured by tuning the unit, batch-size, and embedding size of the LSTM. As a result of the measurement, the loss was 41.9% and the accuracy was 11.4%, and the trend of the optimization model showed a consistently stable graph, confirming that the tuning of the hyperparameter had a profound effect on the model. In addition, it was confirmed that the decision of the embedding size among the three hyperparameters had the greatest influence on the model. In the future, this research will be continued, and research on an algorithm that allows the model to directly find the optimal hyperparameter will continue.

• Applied Microscopy
• /
• v.39 no.4
• /
• pp.349-354
• /
• 2009

In this paper we have constructed three dimensional images and examined structural failure on thin film transistor (TFT) liquid crystal display (LCD) by using dual-beam focused ion beam (FIB) and IMOD software. Specimen was sectioned with dual-beam focused ion beam. Series of two dimensional images were obtained by scanning electron microscopy. Three dimensional reconstruction was constructed from them by using IMOD software. The short defect between Gate layer and Data layer was found from the result of three dimensional reconstruction. That phenomena made the function of the gate lost and data signal supplied to the electrode though the Drain continuously. That signal made continuous line defect. The result of the three dimensional reconstruction, serial section, SEM imaging by using the FIB will be the foundation of the next advanced study.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.5
• /
• pp.354-365
• /
• 2015

This work presents an Internet of Things (IoT) system for home energy management based on a custom-designed Impulse Radio Ultra-Wideband (IR-UWB) transceiver that targets a generic and multi-standard control system. This control system enables the interoperability of heterogeneous devices: it integrates various sensor nodes based on ZigBee, EnOcean and UWB in the same middleware by utilizing an ad-hoc layer as an interface between the hardware and software. The paper presents as a first the design of the IR-UWB transceiver for a portable sensor node integrated with the middleware layer, and also describes the receiver connected to the control system. The custom-designed low-power transmitter on the sensor node is fabricated with 130 nm CMOS technology. It generates a signal with a 1.1 ns pulse width while consuming $39{\mu}W$ at 1 Mbps. The UWB sensor node with a temperature measurement capability consumes 5.31 mW, which is lower than the power level of state-of-the-art solutions for smart-home applications. The UWB hardware and software layers necessary to interface with the control system are verified in over-the-air measurements in an actual office environment. With the implementation of the presented sensor node and its integration in the energy management system, we demonstrate achievement of the broad flexibility demanded for IoT.